TRIO-PS67/1AC/24DC/10/M12
Power supply unit
Data sheet
109661_en_00
1
© PHOENIX CONTACT 2021-04-09
Description
TRIO POWER - robust and distributed power supplies with
IP67 degree of protection
The TRIO POWER power supplies with IP67 protection are
distinguished by their functionality and robust design. The
combination of dustproofness and therefore full touch
protection is indicated by the first number of the IP code
(IP6x). The second number (IPx7) indicates protection
against temporary submersion in water. This means that
use in particularly difficult ambient conditions is always
ensured.
The dynamic boost (1.5 x IN for 5 seconds) safely absorbs
starting currents and brief overload situations during
operation, and without a dip in the output voltage. On the
device side, the power supply is equipped with coded
circular connectors.
Technical data (short form)
Input voltage range
Nominal input voltage range
Mains buffering
Nominal output voltage (UN)
Nominal output current (IN)
Dynamic Boost (IDyn.Boost)
Output power (PN)
Output power (PDyn. Boost)
Efficiency
Residual ripple
Features
MTBF (IEC 61709, SN 29500)
–
Startup type tested
–
–
–
–
–
–
Tool-free connection with no danger of mismatching,
thanks to coded circular connectors
Safe operation, thanks to electrically and mechanically
extremely robust design
Worldwide use, thanks to wide-range input
Fixed 24 V DC output voltage
Reliable starting of heavy loads, thanks to dynamic
boost (1.5 x IN for 5 seconds)
Simplified error diagnostics for remote signaling via DCOK signal contact
OVP (Over Voltage Protection) limits surge voltages to
≤30 V DC (EN 61131-2)
100 V AC ... 240 V AC 10 %
110 V DC ... 250 V DC ±10 %
100 V AC ... 240 V AC
110 V DC ... 250 V DC
> 15 ms (120 V AC)
> 15 ms (230 V AC)
24 V DC ±1 %
10 A
15 A (5 s)
240 W
360 W
typ. 91 % (120 V AC)
typ. 93 % (230 V AC)
≤ 10 mVPP
> 1800000 h (25 °C)
> 1000000 h (40 °C)
> 480000 h (60 °C)
Ambient temperature (operation)
-25 °C ... 70 °C (Derating >60°C: 2.5 %/K)
Dimensions W/H/D
136 mm / 240 mm / 53 mm
Weight
Make sure you always use the latest documentation.
It can be downloaded from the product at phoenixcontact.net/products.
-25 °C
1.5 kg
TRIO-PS67/1AC/24DC/10/M12
2
Table of contents
1
Description ..................................................................................................................................1
3
Ordering data ..............................................................................................................................4
2
4
5
6
7
8
Table of contents......................................................................................................................... 2
Technical data.............................................................................................................................5
Symbols used............................................................................................................................ 11
Safety regulations and installation notes ......................................................................................................11
Design .....................................................................................................................................................................12
7.1
7.2
7.3
7.4
7.5
Rating plate ..................................................................................................................................................12
Device connections and functional elements................................................................................................13
Block diagram...............................................................................................................................................14
Device dimensions .......................................................................................................................................15
Drilling pattern for fixing holes.......................................................................................................................15
8.1
8.2
8.3
8.4
8.5
Heat dissipation ............................................................................................................................................15
Mounting position .........................................................................................................................................16
Installation height..........................................................................................................................................16
Keep-out areas .............................................................................................................................................16
Mounting the power supply unit ....................................................................................................................16
8.5.1 Wall mounting / temporary fixing (mounting aid)................................................................................17
8.5.2 Wall mounting ...................................................................................................................................17
8.5.3 Structural profile ................................................................................................................................18
Removing the power supply unit...................................................................................................................18
Mounting/remove .................................................................................................................................................15
8.6
9
Device-side circular connectors ......................................................................................................................18
9.1
9.2
9.3
Coding of field-side circular connectors........................................................................................................18
Connecting field-side circular connectors .....................................................................................................19
Releasing field-side circular connectors .......................................................................................................19
10.1
10.2
Primary side connection and fuse protection ................................................................................................19
10.1.1 1AC supply network ..........................................................................................................................19
10.1.2 DC supply network ............................................................................................................................19
Position of circular connector Input AC .........................................................................................................20
11.1
11.2
11.3
Protection of the secondary side...................................................................................................................20
Output characteristic curve ...........................................................................................................................20
Position of circular connector Output DC ......................................................................................................21
10 Input AC ..................................................................................................................................................................19
11 Output DC ................................................................................................................................. 20
109661_en_00
PHOENIX CONTACT
2/22
TRIO-PS67/1AC/24DC/10/M12
12 Signaling....................................................................................................................................21
12.1
12.2
12.3
AC OK LED .................................................................................................................................................. 21
DC OK-LED.................................................................................................................................................. 21
Floating signal contact.................................................................................................................................. 21
13 Disposal and recycling...............................................................................................................22
109661_en_00
PHOENIX CONTACT
3/22
TRIO-PS67/1AC/24DC/10/M12
3
Ordering data
Description
Type
Order No.
Pcs./Pkt.
Primary-switched power supply unit, TRIO POWER in
IP67 die-cast housing, M12 circular connector, input: 1phase, output: 24 V DC / 10 A
TRIO-PS67/1AC/24DC/10/
M12
1111634
1
Accessories
Type
Order No.
Pcs./Pkt.
Power connector, Power, 3-position, shielded, Socket
straight M12, Coding: S, Push-lock spring connection,
knurl material: Nickel-plated brass, external cable
diameter 6 mm ... 11 mm
SACC-M12FSS-2PEPL-CM
SH
1080227
SAC-3P- 1,0-PUR/M12FSS
PE
1176479
1
Power connector, Power, 4-position, shielded, Plug
straight M12, Coding: L, Push-lock spring connection,
knurl material: Nickel-plated brass, external cable
diameter 6 mm ... 11 mm
SACC-M12MSL-4PL-CM SH
1080239
1
1425025
1
Connector, Universal, 5-position, unshielded, Socket
straight M12, Coding: A, Push-in connection, knurl
material: Zinc die-cast, nickel-plated, external cable
diameter 4 mm ... 8 mm
SACC-M12FS-5PL M
1424652
1
SAC-5P- 1,5-PUR/M12FS
1669822
1
Power cable, 3-position, PUR halogen-free, black, free
cable end, on Socket straight M12, coding: S, cable
length: 1 m, for AC current up to 16 A/230 V
Power cable, 4-position, PUR halogen-free, black-gray
SAC-4P-M12MSL/ 1,5-105
RAL 7021, Plug straight M12, coding: L, on free cable end,
cable length: 1.5 m, For direct current up to 12 A/63 V
Sensor/actuator cable, 5-position, PUR halogen-free,
black-gray RAL 7021, free cable end, on Socket straight
M12, coding: A, cable length: 1.5 m
1
Our range of accessories is being continually extended, our current range can be found in the download area.
109661_en_00
PHOENIX CONTACT
4/22
TRIO-PS67/1AC/24DC/10/M12
4
Technical data
Input data
All technical specifications are nominal values and are based on an ambient temperature of 25°C and
70% relative humidity at 2000 m above sea level.
Input voltage range
(for DC, connect a suitable fuse)
100 V AC ... 240 V AC 10 %
110 V DC ... 250 V DC ±10 %
Switch-on voltage typ.
≥ 95 V DC
Nominal input voltage range
100 V AC ... 240 V AC
110 V DC ... 250 V DC
Shut-down voltage typ.
< 95 V DC
Electric strength, max.
≤ 300 V AC (15 s)
Network type
Star network (TN, TT, IT (PE))
Frequency range (fN)
50 Hz ... 60 Hz ±10 %
Current consumption (for nominal values) typ.
2.8 A (100 V AC)
1.2 A (240 V AC)
2.4 A (110 V DC)
1.1 A (250 V DC)
Switch-on time
15 ms (120 V AC)
> 15 ms (230 V AC)
Inrush current integral (I2t)
< 0.5 A2s
Input fuse internal (device protection)
6.3 A
Inrush current limitation after 1 ms
typ. 25 A
Recommended breaker for input protection
6 A ... 16 A (US/CAN: branch circuit protection 0.9 x UN
(UN = 24 V DC)
DC OK
Contact assignment
13/14 (closed)
Signal threshold
UOUT > 0.9 x UN (UN = 24 V DC)
Maximum contact load
Signal connection data
Connection method
30 V AC/30 V DC(100 mA )
M12 circular connector
Type of locking
M12
Number of positions
5 (Plug)
Coding
A-coded
Reliability
230 V AC
MTBF (IEC 61709, SN 29500)
General data
Degree of protection
> 1800000 h (25 °C)
> 1000000 h (40 °C)
> 480000 h (60 °C)
IP67
Protection class
I
Type of housing
Aluminum (AlMg3)
Weight
1.5 kg
Inflammability class in acc. with UL 94 (housing / terminal V0
blocks)
Dimensions W / H / D (state of delivery)
Power dissipation
Maximum power dissipation in no-load condition
Power loss nominal load max.
109661_en_00
136 mm / 240 mm / 53 mm
120 V AC
230 V AC
< 22 W
< 17 W
< 10 W
60°C: 2.5 %/K)
Ambient temperature (start-up type tested)
-25 °C
Max. permissible relative humidity (operation)
≤ 100 % (at 25 °C, non-condensing)
Ambient temperature (storage/transport)
Installation height
Vibration (operation)
Shock
Degree of pollution
Climatic class
Overvoltage category
EN 61010-1
Standards
Electrical safety
-40 °C ... 85 °C
≤ 4000 m (> 2000 m, Derating: 10 %/1000 m)
< 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6)
15 Hz ... 150 Hz, 4g, 90 min.
18 ms, 30g, in each space direction (according to IEC 600682-27)
3
3K3 (in acc. with EN 60721)
III (≤ 2000 m)
IEC 61010-1 (SELV)
Safety requirements for electrical equipment for
measurement, control, and laboratory use
IEC 61010-1
Safe isolation
IEC 61558-2-16
Safety extra-low voltage
Low-voltage power supplies, DC output
Limit values for harmonic currents
Degrees of protection provided by enclosures (IP code)
Approvals
UL
IEC 61010-1 (SELV)
IEC 61010-2-201 (PELV)
EN 61204-3
EN 61000-3-2
EN/IEC 60529
UL/C-UL Listed UL 61010-1
UL/C-UL Listed UL 61010-2-201
Current approvals/permissions for the product can be found in the download area under
phoenixcontact.net/products
109661_en_00
PHOENIX CONTACT
8/22
TRIO-PS67/1AC/24DC/10/M12
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Noise emission according to EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
CE basic standard
Conducted noise emission EN 55016
Minimum normative
requirements
Higher requirements in
practice (covered)
EN 61000-6-4 (Class A)
EN 61000-6-3 (Class B)
EN 61000-6-4 (Class A)
Noise emission EN 55016
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial)
CE basic standard
Electrostatic discharge EN 61000-4-2
Housing contact discharge
Electromagnetic HF field EN 61000-4-3
Comments
Frequency range
Minimum normative
requirements of EN 610006-2 (CE)
(immunity for industrial
environments)
Higher requirements in
practice (covered)
4 kV (Test Level 2)
6 kV (Test Level 3)
Criterion B
80 MHz ... 1 GHz
Criterion A
80 MHz ... 1 GHz
Test field strength
10 V/m (Test Level 3)
10 V/m (Test Level 3)
Test field strength
3 V/m (Test Level 2)
10 V/m (Test Level 3)
Test field strength
1 V/m (Test Level 1)
10 V/m (Test Level 3)
Input
2 kV (Test Level 3 asymmetrical)
4 kV (Test Level 3 asymmetrical)
1 kV (Test Level 3 asymmetrical)
2 kV (Test Level 3 asymmetrical)
1 kV (Test Level 1 symmetrical)
2 kV (Test Level 1 asymmetrical)
2 kV (Test Level 4 symmetrical)
4 kV (Test Level 4 asymmetrical)
Frequency range
Frequency range
Fast transients (burst) EN 61000-4-4
Comments
Output
Signal
Surge voltage load (surge) EN 61000-4-5
Comments
Input
Output
Signal
Comments
109661_en_00
EN 61000-6-3 (Class B)
1.4 GHz ... 2 GHz
2 GHz ... 2.7 GHz
Criterion B
2 kV (Test Level 3 asymmetrical)
Criterion B
1 GHz ... 2 GHz
2 GHz ... 6 GHz
Criterion A
2 kV (Test Level 3 asymmetrical)
Criterion A
0.5 kV (Test Level 1 symmetrical)
0.5 kV (Test Level 1 asymmetrical)
1 kV (Test Level 3 symmetrical)
2 kV (Test Level 3 asymmetrical)
Criterion B
Criterion A
1 kV (Test Level 2 asymmetrical)
1 kV (Test Level 2 asymmetrical)
PHOENIX CONTACT
9/22
TRIO-PS67/1AC/24DC/10/M12
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial)
CE basic standard
Conducted interference EN 61000-4-6
Input/output
Frequency range
Voltage
Voltage dips EN 61000-4-11
Input voltage (230 V AC, 50 Hz)
Comments
Criterion B
0.15 MHz ... 80 MHz
0.15 MHz ... 80 MHz
Criterion A
Criterion A
10 V (Test Level 3)
10 V (Test Level 3)
Voltage dip
40 % , 10 periods
40 % , 10 periods
Voltage dip
0 % , 1 period
0 % , 1 period
Criterion C
Criterion C
Criterion B
Criterion A
Criterion A
Criterion A
Normal operating behavior within the specified limits.
Temporary impairment to operational behavior that is corrected by the device itself.
Temporary adverse effects on the operating behavior, which the device corrects
automatically or which can be restored by actuating the operating elements.
Emitted interference in acc. with EN 61000-6-3
Radio interference voltage in acc. with EN 55011
Emitted radio interference in acc. with EN 55011
109661_en_00
asymmetrical
70 % , 25 periods
Comments
Criterion C
asymmetrical
70 % , 25 periods
Comments
Criterion A
Higher requirements in
practice (covered)
Voltage dip
Comments
Key
Minimum normative
requirements of EN 610006-2 (CE)
(immunity for industrial
environments)
EN 55011 (EN 55022) Class B, area of application: Industry
and residential
EN 55011 (EN 55022) Class B, area of application: Industry
and residential
PHOENIX CONTACT
10/22
TRIO-PS67/1AC/24DC/10/M12
5
Symbols used
In this data sheet, symbols are used to draw your attention
to important information and potential dangers.
WARNING
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety measures that follow this symbol to avoid
possible personal injuries.
There are different categories of personal injury that are
indicated by a signal word.
WARNING
This indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
This indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTE
6
Safety regulations and installation
notes
Before mounting, starting up or operating the
power supply, carefully read through the data
sheet.
WARNING: Danger to life by electric shock!
– Only qualified specialist personnel may
mount, start up, and operate the power
supply.
– Establish connection correctly and ensure
protection against electric shock.
– It must be possible to switch off the device
outside the power supply in accordance with
the regulations of EN 61010-1 (e.g., by line
protection on the primary side).
– The protective conductor connection for the
supply source must be wired to the ground
conductor contact in the field-side circular
connector.
– Never carry out work when voltage is present.
Indication of a required action which if it is not
performed may cause damage or malfunction to
the device, hardware/software, or surrounding
property.
This symbol and the accompanying text provide
the reader with additional information or refer to
detailed sources of information.
109661_en_00
PHOENIX CONTACT
11/22
TRIO-PS67/1AC/24DC/10/M12
7
Design
7.1
Rating plate
In accordance with the German Product Safety Law
(ProdSG) it is only permissible to make such products
available on the market if they meet certain safety
standards. It must be ensured at all times that users are not
exposed to hazards.
In accordance with ProdSG, every device must therefore be
fitted with a rating plate. All relevant information on the safe
use of the device must also be included.
The power supply device rating plate is located on
the front of the housing (as viewed from the front).
Figure 1
1
2
3
Phoenix Contact GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg, Germany
12
11
-25
10
4
Made by Phoenix Contact in China
Sno. XXXXXXXXXXXXX D0001
V/C:
9
www.phoenixcontact.com
Date:
8
7
5
6
Key
No.
1
2
3
4
5
6
7
8
9
10
11
12
109661_en_00
Rating plate information
Documentation
NOTE
– Observe the national safety and accident
prevention regulations.
– Assembly and electrical installation must
correspond to the state of the art.
– The die-cast housing and the device-side
circular connectors satisfy the requirements
of IP67 protection.
– Outdoor mounting is allowed.
– Avoid an installation location with direct
sunlight.
– If the ambient temperature at the mounting
location is >45°C, prevent direct contact with
the power supply. For example, use an
additional control cabinet (restricted access
location).
– Observe the mechanical and thermal limits at
the installation location.
– Mount the power supply in the normal
mounting position (device-side circular
connectors below).
– Adequate keep-out zones must be ensured
for heat emission.
– Ensure that the primary-side wiring and
secondary-side wiring are the correct size and
have sufficient fuse protection.
– The connection parameters, e.g., required
stripping lengths for the wiring, can be found
in the installation information for the
respective field-side circular connector.
– Use copper cables with an operating
temperature ≥105°C (ambient temperature
85°C).
– The power supply is approved for connection
to TN, TT, and IT (PE) power grids (star
networks) with a maximum phase-to-phase
voltage of 240 V AC.
– The power supply is maintenance-free.
Repairs may only be carried out by the
manufacturer. The warranty no longer applies
if the housing is opened.
– The power supply may only be used for its
intended use.
Designation
Identification of the provider
QR code as web link to the device documentation
Device approvals
Device-specific warning notice and designation of device documentation accompanying
the product
Production site of the Phoenix Contact Group
Note on disposal
Bar code and serial number for device identification
Date of manufacture
Designation of device revision
Ambient conditions
Device connection data
Product designation
PHOENIX CONTACT
12/22
TRIO-PS67/1AC/24DC/10/M12
7.2
Device connections and functional elements
Device connections are labeled with connection tags to
ensure clear and definitive identification.
The connection tags are split into the following connection
levels:
Connection
level
1.
2.
3.
Figure 2
Description
Key
No. Designation
1
2
3
AC input
DC output
Signal contact
4
Location of functional elements and device
connections
3
2
2
5
6
7
8
9
1
10
11
4
Die-cast housing
Mounting holes (Ø 5.6mm, external)
for console or wall mounting
Mounting holes (Ø 5.6 mm, centered)
for mounting on structural or strut profiles
Pressure compensation membrane
(bottom of the housing)
QR code web link
Signaling DC OK LED
Screw connecting plug (female connector) for output voltage
Connection
labeling
---Output DC
Signal
Input AC
Screw connecting plug (male connector) for input voltage
AC OK LED signaling
-Marking field, e.g., for plant and loca- -tion identification
Documentation
Phoenix Contact GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg, Germany
TRIO-PS67/ 1AC / 24DC / 10 / M12
Order - No.:1111634
5
11
Input AC 100-240V
10
2
109661_en_00
N
(3)
14
14
(4)
13
(1)
3
0V
(2)
0V
(3)
24V
(1)
24V
(4)
6
DC OK
AC OK
L
(1)
9
Output AC 24V 10A
DC OK
13
PE
(2)
8
7
2
PHOENIX CONTACT
13/22
TRIO-PS67/1AC/24DC/10/M12
7.3
Block diagram
Figure 3
Block diagram
Input AC
L
1
PE
2
N
3
Output D C
1 24V
2
Filter 3 0V
4 24V
active
PFC
Filter
1
2
3
4
5
Signal
Functions
UVP
OVP
13
14
User Interface
OTP
OCP
SCP
AC OK
DC OK
Key
Symbol
Filter
Designation – Input AC, Output DC
Input fuse, internal device protection
Symbol
UVP
EMC filter
OVP
Rectification
aktive
PFC
Power factor correction (PFC)
OTP
Switching transistor
OCP
Transmitter with electrical isolation
SCP
Smoothing capacitor
Electrically isolated signal transmission (optocoupler)
Control equipment
Symbol
Designation – Signal
Floating switch contact (13/14) for forwarding
the operational readiness to a superordinate
control system.
Symbol
Designation – User interface
AC OK LED indicates whether the AC input
voltage for power supply is present
AC OK
DC OK
109661_en_00
Designation – Functions
Undervoltage protection protects the AC
input of the power supply against damage in
the event of an AC undervoltage.
Overvoltage protection protects the DC output of the power supply and the connected
load against damage in the event of an overvoltage
Overtemperature protection protects the
power supply against damage in the event of
impermissibly high intrinsic external heating.
Overcurrent protection protects the DC output of the power supply against damage in
the event of an impermissibly high current
load.
Short-circuit protection protects the DC output of the power supply against damage in
the vent of an output-side short circuit.
DC OK LED, indicates the operating status of
the power supply
PHOENIX CONTACT
14/22
TRIO-PS67/1AC/24DC/10/M12
7.4
Device dimensions
Figure 4
Device dimensions (dimensions in mm)
136
53
8
Mounting/remove
The power supply is mounted on a console or directly on a
flat mounting surface (wall mounting). Mounting on
structural or strut profiles is also possible.
8.1
Heat dissipation
Heat is dissipated from the power supply as radiant heat via
the heatsink integrated in the housing cover. During
mounting, observe the minimum distances specified for the
device side (see section: keep-out zones).
Heat dissipation through radiant heat
240
Figure 6
Documentation
Phoenix Contact GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg, Germany
TRIO-PS67/ 1AC / 24DC / 10 / M12
Order - No.:1111634
Input AC 100-240V
N
(3)
14
14
(4)
0V
(2)
0V
(3)
24V
(1)
24V
(4)
DC OK
AC OK
L
(1)
Output AC 24V 10A
DC OK
13
PE
(2)
13
(1)
Documentation
. KG
& Co
bH
ct Gm
nta
Co 8 rmany
, Ge
tr.
oenix rkts
Ph ma erg
chs mb
Fla 5 Blo
3282
TR
IO-PS
r
Orde
7.5
67
24
C/
/ 1A
DC
/ 10
/ M1
2
1634
A
.:111
- No
V
Drilling pattern for fixing holes
DC
OK14
DC
OK
0V
)
(2
DC
24
10
0V
)
(3
V
24
)
(4
V
24
)
(1
13
V
40
0-2
The power supply is mounted on a flat, loadbearing surface. Fix the power supply in place at
the outer corners with at least four mounting
screws (hole dimensions: 120 x 228 mm).
ut
tp
Ou
ut
Inp
AC
10
14
)
(4
OK
AC
13
)
(1
N
)
(3
PE
)
(2
L
)
(1
If the operating conditions are particularly difficult,
e.g., due to vibration, six mounting screws can be
used.
Figure 5
Drilling pattern for fixing holes (dimensions in
mm)
60
228
60
109661_en_00
PHOENIX CONTACT
15/22
TRIO-PS67/1AC/24DC/10/M12
8.2
Mounting position
The specified technical data for the power supply is based
on nominal operation.
8.4
Keep-out areas
In the normal mounting position, the power supply
is mounted on a flat surface with mounting screws.
The power supply is not subject to positiondependent derating.
Figure 8
Power supply installed in the normal mounting
position
136
20
20
50
Figure 7
Device dimensions and minimum keep-out
areas (in mm)
Documentation
. KG
& Co
bH
ct Gm
nta
Co 8 rmany
, Ge
tr.
oenix rkts
Ph ma erg
chs mb
Fla 5 Blo
3282
/ M1
/ 10
2
1634
A
.:111
- No
V
ut
tp
Ou
DC
OK14
DC
OK
0V
)
(2
DC
24
10
0V
)
(3
V
24
)
(4
Phoenix Contact GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg, Germany
V
24
)
(1
TRIO-PS67/ 1AC / 24DC / 10 / M12
13
V
40
0-2
ut
AC
10
Inp
Order - No.:1111634
14
)
(4
OK
AC
Documentation
IO-PS
r
Orde
24DC
240
TR
C/
1A
67/
13
)
(1
N
)
(3
PE
)
(2
L
)
(1
Input AC 100-240V
N
(3)
Installation height
You can operate the power supply without power limitations
up to an installation altitude of 2000 m. For altitudes higher
than 2000 m, different specifications apply due to the
differing air pressure and the reduced convection cooling
associated with this (see section: Technical data, Ambient
conditions).
0V
(2)
0V
(3)
24V
(1)
24V
(4)
DC OK
13
(1)
100
8.3
14
14
(4)
AC OK
L
(1)
Output AC 24V 10A
DC OK
13
PE
(2)
8.5
Mounting the power supply unit
A supporting substructure, mounting wall, or structural
profile is essential for the installation of the power supply.
The device-side connector (circular connector) is at the
bottom when installing in the standard installation position.
The die-cast housing is fixed with two or four screws,
depending on the type of mounting. Use either Allen screws
(such as M5 x 40, ISO 4762) or hexalobular internal driving
screws (such as 5 x 40, ISO 10664). In order to secure the
screws, use spring washers in accordance with ISO 10670.
Depending on the required mounting position of
the power supply, use the temporary mounting aid
(eye) to accurately prepare the four mounting
holes. They are located in the middle on the top or
bottom mounting flange.
109661_en_00
PHOENIX CONTACT
16/22
TRIO-PS67/1AC/24DC/10/M12
8.5.1
Wall mounting / temporary fixing (mounting
aid)
Figure 9
Drilling pattern for temporary mounting
60
60
For temporary fixing, use the same screws as for standard
fixing (e.g., M5 x 40, ISO 4762 or hexalobular internal
driving screws, e.g., 5 x 40, ISO 10664).
Figure 10
Schematic diagram of temporary mounting aid
8.5.2
Wall mounting
Proceed as follows to mount the power supply:
1. Copy the entire drilling pattern onto the substructure or
mounting wall.
2. Select suitable fixing material depending on the
substructure or mounting wall
3. Drill the necessary number of drill holes using a suitable
drill, depending on the type of fixing (threaded or wall
plug mounting).
4. Prepare the drill hole(s) for the temporary mounting aid
(tap M5 thread or insert 8 x 70 mm wall plug).
5. Fix the die-cast housing in place using four screws and
four spring washers
6. Check that the die-cast housing is securely mounted
Figure 11
109661_en_00
. KG
& Co
bH
ct Gm
nta
Co tr. 8 rmany
oenix rkts , Ge
Ph ma erg
chs mb
Fla 5 Blo
3282
Documentation
Proceed as follows to temporarily secure the power supply:
1. Select the appropriate mounting location and the
required mounting position. Observe the required keepout zones.
2. Depending on the mounting position, one or two drill
holes are needed as a temporary mounting aid.
3. Drill the necessary number of drill holes using a suitable
drill, depending on the type of fixing (threaded or wall
plug mounting).
4. Prepare the drill hole(s) for the temporary mounting aid
(tap M5 thread or insert 8 x 70 mm wall plug).
5. Screw the required number of screws into the fixing
holes using a suitable tool so that the screws are still
protruding by min. 10 mm.
6. Place the power supply onto the screws, so that they
hold it securely in place.
7. Now perform the actual wall mounting process (see
section: Wall mounting)
Schematic diagram of wall mounting
24DC
C/
1A
67/
IO-PS
1634
TR
.:111
No
rOrde
A
/ M1
/ 10
2
A
V
ut
tp
Ou
DC
OK14
DC
OK
0V
)
(2
DC
24
10
0V
)
(3
V
24
)
(4
V
24
)
(1
13
V
40
0-2
ut
Inp
AC
10
14
)
(4
OK
AC
13
)
(1
N
)
(3
PE
)
(2
L
)
(1
B
PHOENIX CONTACT
17/22
TRIO-PS67/1AC/24DC/10/M12
8.5.3
Structural profile
Proceed as follows to mount the power supply:
1. Position the two sliding blocks for fixing in the mounting
profile
2. Use the center fixing holes (top, bottom) to fix the diecast housing
3. Fix the die-cast housing in place using two screws and
two spring washers
4. Check that the die-cast housing is securely mounted
Figure 12
9
On the device side, all the connection contacts of the power
supply are circular connectors. For the respective contact
assignment of the circular connectors for the device supply
or load supply, please refer to the relevant section on the
input, output or signaling.
For protection against fatal electric shock, the diecast housing is wired internally to the protective
conductor connection of the device-side circular
connector for the AC input voltage.
Schematic diagram, structural profile mounting
A
Optionally available circular connectors are
required for the field-side connection of the power
supply (see accessories).
B
9.1
Documentation
2
A
/ M1
/ 10
A
V
ut
tp
Ou
DC
OK14
OK
DC
0V
)
(2
DC
24
10
0V
)
(3
V
24
)
(4
V
24
)
(1
13
8.6
V
40
0-2
t
pu
In
AC
10
14
)
(4
OK
AC
Coding of field-side circular connectors
Each field-side circular connector that is required is
assigned its special function with different coding. Incorrect
connection between Input AC, Output DC, and floating
signal contact 13/14 is therefore impossible.
. KG
& Co
bH
ct Gm
ny
nta
x Co tr. 8 rma
eni rkts , Ge
Pho ma erg
chs mb
Fla 25 Blo
328
24DC
C/
1A
67/
PS
IO1634
TR
.:111
No
rOrde
B
Device-side circular connectors
13
)
(1
N
)
(3
PE
)
(2
L
)
(1
For the coding of field-side circular connectors, refer to the
table below:
Device-side marking
Input AC
Output DC
13/14 (floating contact)
Coding
S-coded
A-coded
Removing the power supply unit
For added security, before loosening all the
mounting screws, use the two screws of the
temporary mounting aid again.
To remove the power supply, perform the same procedure
for the relevant type of fixing (wall mounting, structural
profile mounting) in reverse.
109661_en_00
PHOENIX CONTACT
18/22
TRIO-PS67/1AC/24DC/10/M12
9.2
Connecting field-side circular connectors
The field-side circular connectors to be used are coded like
the device-side circular connectors. This ensures clear
assignment between AC device supply, DC load supply,
and the signal contact. Unintentional incorrect connection is
prevented.
Figure 13
Schematic diagram, connecting field-side
circular connectors
10
Input AC
The power supply is approved for connection to TN, TT, and
IT (PE) power grids (star networks) with a maximum phaseto-phase voltage of 240 V AC.
Connection is via the device-side circular connector,
connection level 1 (Input AC).
10.1
Primary side connection and fuse protection
The installation of the power supply must conform to the
regulations of EN 61010. It must be possible to switch off the
power supply using a suitable disconnect device outside the
power supply. For example, the primary-side line protection
is suitable for this (see technical data).
10.1.1 1AC supply network
Figure 14
bH
Documentation
ct Gm
y
nta 8
rman
, Ge
Co
str.
oenix rkt
Ph ma erg
chs mb
Fla 5 Blo
3282
TR
24DC
C/
7/ 1A
1634
.:111
- No
/ 10
/ M1
2
S6
IO-P
r
Orde
A
V
ut
tp
Ou
DC
OK14
DC
OK
0V
)
(2
DC
24
10
0V
)
(3
V
24
)
(4
V
24
)
(1
13
0V
14
)
(4
24
ut
AC
00
1
Inp
PE
)
(2
L
)
(1
OK
AC
B
Proceed as follows to connect the field-side circular
connectors:
B
9.3
Depending on their assigned functionality and coding, securely attach the field-side circular connectors
to the device-side circular connectors.
To lock the circular connectors, tighten the screw
locking by turning it clockwise.
Releasing field-side circular connectors
To release the field-side circular connectors, perform the
same procedure in reverse.
109661_en_00
L1
L2
L3
N
PE
Input 1AC
TN-C
L1
L2
L3
Input 1AC
N
PE
PEN
13
)
(1
N
)
(3
A
A
Permissible network types for AC supply
TT / TN / IT (PE)
. KG
& Co
Input AC
Input AC
1 L
1 L
2 PE
2 PE
3 N
3 N
10.1.2 DC supply network
Operation on DC power grids is also possible in accordance
with the DC nominal input voltage.
DANGER: Hazardous voltage
When operating the power supply on a DC voltage
system, observe the maximum permissible input
voltage (see section: Technical data).
The primary-side fuse protection in DC operation
must cover all poles.
NOTE: Damage possible if an incorrect fuse is
used
In DC operation, only use fuses that are approved
for DC voltages.
PHOENIX CONTACT
19/22
TRIO-PS67/1AC/24DC/10/M12
Figure 15
Schematic diagram, two-phase fuse protection
Input DC
+
PE
The power supply is electronically short-circuit-proof and
no-load-proof. In the event of an error, the output voltage is
limited
11.2
2 PE
3 N
Position of circular connector Input AC
Figure 16
Device-side position and contact assignment
of circular connector Input AC
DC OK
Input AC 100-240V
13
PE
(2)
Output DC 24V 10A
14
14
(4)
N
(3)
13
(1)
L
(1)
Contact assignment
Contact plug 1
Contact plug 2
Contact plug 3
0V
(2)
0V
(3)
24V
(1)
24V
(4)
Description
Figure 18
A DC voltage for supplying the load is provided at the output
of the power supply.
Upon delivery, the power supply is preset to a nominal
output voltage of 24 V DC. The output voltage value cannot
be changed.
U/I characteristic curve with dynamic load
reserve
dyn. Boost
t≥5s
UN
U < 0,9 x UN
L/+ (mains supply)
Protective conductor connection PE
N/- (mains supply)
Output DC
Output characteristic curve
The power supply works with a dynamic power reserve, the
dynamic boost, as shown in the U/I characteristic curve in
the figure. In the event of a secondary-side short circuit or
overload, the output current is limited to 1.5 x IN. The
module does not switch off, but supplies a continuous output
current instead. The secondary voltage is then reduced until
the short circuit is eliminated. The U/I characteristic curve
with the dynamic power reserve enables high switch-on
currents of capacitive loads or inductive loads to be supplied
reliably.
UOUT [V]
1 L
11
Protection of the secondary side
Overvoltage protection (OVP) limits surge voltages at the
DC output to ≤30 V DC (EN 61131-2)
Input AC
10.2
11.1
IN
–
–
–
–
–
UN = 24 V
IN = 10 A
PN = 240 W
Idyn. BOOST = 15 A (5 s)
Pdyn. BOOST = 360 W (5 s)
1,5 x IN
IOUT [A]
Connection is via the device-side circular connector,
connection level 2 (Output DC).
Figure 17
Wiring principle, DC output
+24V
+24V
0V
Output DC
24V 1
2
0V
3
24V 4
109661_en_00
PHOENIX CONTACT
20/22
TRIO-PS67/1AC/24DC/10/M12
11.3
Position of circular connector Output DC
Figure 19
Device-side position and contact assignment
of circular connector Output DC
DC OK
Input AC 100-240V
13
PE
(2)
Output DC 24V 10A
13
(1)
L
(1)
Floating signal contact
A floating switch contact can be used to forward data to a
higher-level control system. If the input voltage (0.55 x ACN)
is undershot or the nominal output voltage UOUT is 90% of the nominal output voltage
UOUT (24 V DC), the LED is steady green. If the DC output
voltage falls below the specified limit value, e.g., due to
disruption of the supplied DC output load, the LED is no
longer activated.
109661_en_00
Device-side position and contact assignment
of circular connector 13/14
DC OK
Input AC 100-240V
13
PE
(2)
N
(3)
L
(1)
Contact assignment
Contact plug 1
Contact plug 2
Contact plug 3
Contact plug 4
Contact plug 5
Output DC 24V 10A
14
14
(4)
13
(1)
0V
(2)
0V
(3)
24V
(1)
24V
(4)
Description
Floating switch contact (13)
not used
not used
Floating switch contact (14)
not used
PHOENIX CONTACT
21/22
TRIO-PS67/1AC/24DC/10/M12
13
Disposal and recycling
Ensure the correct disposal of electronic
components
Do not dispose of the power supply as household
waste.
Observe the applicable national standards and
regulations.
Ensure correct disposal or recycling
Dispose of or recycle packaging material that is no
longer needed as household waste.
Observe the applicable national standards and
regulations.
109661_en_00
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
phoenixcontact.com
22/22