1401075

SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user documentation. Our general terms of use for downloads are valid. Device connector front mounting, Universal, 4-position, Pin, straight, M12, coding: A, on free cable end, Front mounting, Pg9, Individual wires, cable length: 0.5 m, 0.34 mm2, TPE litz wire Your advantages • Preassembled with litz wires for immediate use • Customer-specific assemblies and litz wire lengths available • Sealed on the litz wire side for optimum leak-tightness • All standard pin assignments and codings for signal, data, and power transmission with a uniform design-in design • For high transmission safety: shield connection to the housing with optional EMC nut Commercial data Item number 1401075 Packing unit 1 pc Minimum order quantity 100 pc Product key ABQCEE GTIN 4046356522311 Weight per piece (including packing) 28.4 g Weight per piece (excluding packing) 18.6 g Customs tariff number 85444290 Country of origin DE Jan 8, 2024, 10:02 AM Page 1 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Technical data Notes General The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. General Contact connection method: Crimp connection Safety note Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory Jan 8, 2024, 10:02 AM Page 2 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Mounting Mounting type Front mounting Pg9 Connection method Individual wires Product properties Product type Circular connectors (device side) Sensor type Universal Number of positions 4 No. of cable outlets 1 Shielded no Coding A Thread type M12 Insulation characteristics Overvoltage category II Degree of pollution 3 Material specifications Flammability rating according to UL 94 V0 Seal material NBR Contact material CuZn Contact surface material Ni/Au Contact carrier material PA 66 Material for screw connection Brass, nickel-plated Conductor material Tin-plated Cu litz wires Electrical properties Nominal voltage UN 250 V Nominal current IN 4A Max. conductor resistance 57.6 Ω/km Connection data Conductor connection Connection method Individual wires Jan 8, 2024, 10:02 AM Page 3 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Contact connection type Pin Conductor cross section 0.34 mm² Connector Connection 1 Head design Pin Head cable outlet straight Head thread type M12 Coding A Connection 2 Head design free cable end Cable/line Cable length 0.5 m Cable type TPE litz wire Signal type/category Universal Wire diameter incl. insulation 1.2 mm ±0.07 mm Single wire, color brown, white, blue, black Cable cross section 0.34 mm² Conductor material Tin-plated Cu litz wires Conductor structure signal line 7x 0.25 mm AWG signal line 22 Material wire insulation TPE Thickness, insulation 0.21 mm Nominal voltage, cable 300 V Test voltage, cable 2000 V AC Cable resistance ≤ 57.6 Ω/km Cable insulation resistance ≥ 20 MΩ*km Environmental and real-life conditions Ambient conditions Degree of protection IP67 IP67 Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) -25 °C ... 90 °C (cable, fixed installation) Standards and regulations Standard designation M12 connector Standards/specifications IEC 61076-2-101 Jan 8, 2024, 10:02 AM Page 4 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Drawings Schematic diagram 4 3 1 2 Pin assignment M12 plug, 4-pos., A-coded, view plug side Jan 8, 2024, 10:02 AM Page 5 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Circuit diagram 1 BN 2 WH 4 BK 3 BU Jan 8, 2024, 10:02 AM Page 6 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Approvals To download certificates, visit the product detail page: https://www.phoenixcontact.com/pc/products/1401075  UL Recognized Approval ID: E118976-20100522 Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2 250 V 4A - 22 - Jan 8, 2024, 10:02 AM Page 7 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Classifications ECLASS ECLASS-11.0 27440102 ECLASS-12.0 27440116 ECLASS-13.0 27440116 ETIM ETIM 9.0 EC002635 UNSPSC UNSPSC 21.0 39121400 Jan 8, 2024, 10:02 AM Page 8 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Environmental product compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Jan 8, 2024, 10:02 AM Page 9 (11) SACC-E-M12MS-4CON-PG9/0,5 PO - Device connector front mounting 1401075 https://www.phoenixcontact.com/pc/products/1401075 Accessories SACC-E-MU-PG9 - Flat nut 1504084 https://www.phoenixcontact.com/pc/products/1504084 Flat nut, Screw mounting, Pg9, cable gland Pg9, Alternative product in accordance with RoHS II without Exemption 6c (Pb