1405233

https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Sensor/actuator flush-type plug, 4-pos., stainless steel, A-coded, front/screw mounting with M16 thread, with 0.5 m TPE litz wire, 4 x 0.34 mm² Your advantages  Pre-assembled with litz wires for immediate use  Customer-specific assemblies and litz wire lengths available  Sealed on the litz wire side for optimum leak-tightness  All standard pin assignments and codings for signal, data, and power transmission with a uniform design-in design  For high transmission safety: shield connection to the housing with optional EMC nut Key Commercial Data Packing unit 1 pc GTIN GTIN 4046356748100 Weight per Piece (excluding packing) 20.000 g Custom tariff number 85444290 Country of origin Germany Technical data Dimensions Length of cable 0.5 m Ambient conditions Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) -40 °C ... 85 °C (without mechanical actuation) 10/13/2019   Page 1 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Technical data Ambient conditions Degree of protection IP67 General Note The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Rated current at 40°C 4A Rated voltage 250 V Rated surge voltage 2.5 kV Number of positions 4 Insulation resistance ≥ 100 MΩ Coding A - standard Standards/regulations M12 connector IEC 61076-2-101 Signal type/category Universal Status display No Overvoltage category II Degree of pollution 3 Connection method Individual wires Insertion/withdrawal cycles > 100 Torque 3 Nm ... 4 Nm (Installation-side) Mounting type Front mounting M16 x 1.5 Material Flammability rating according to UL 94 V0 Contact material CuZn Contact surface material Ni/Au Contact carrier material PA 6.6 Material, knurls Stainless steel Sealing material FKM Cable Cable type TPE litz wire Conductor cross section 0.34 mm² AWG signal line 22 Conductor structure signal line 7x 0.25 mm Core diameter including insulation 1.2 mm ±0.07 mm Thickness, insulation 0.21 mm (Core insulation) Wire colors brown, white, blue, black 10/13/2019   Page 2 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Technical data Cable Material conductor insulation TPE Conductor material Tin-plated Cu litz wires Standards/specifications M12 connector IEC 61076-2-101 Insulation resistance ≥ 20 MΩ*km Conductor resistance ≤ 57.6 mΩ/m Nominal voltage, cable 300 V Test voltage, cable 2000 V AC Ambient temperature (operation) -40 °C ... 85 °C (cable, fixed installation) -25 °C ... 85 °C (cable, flexible installation) Standards and Regulations Standard designation M12 connector Standards/regulations IEC 61076-2-101 Flammability rating according to UL 94 V0 CE safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product 10/13/2019   Page 3 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Technical data Standards and Regulations • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings Dimensional drawing M12 flush-type plug 10/13/2019   Page 4 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Dimensional drawing Housing cutout for M16 fastening thread, mounting panel with thread 10/13/2019   Page 5 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Circuit diagram Contact assignment of the M12 plug and the M12 socket 10/13/2019   Page 6 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Schematic diagram Pin assignment M12 plug, 4-pos., A-coded, view plug side Classifications eCl@ss eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27143400 eCl@ss 6.0 27279200 eCl@ss 7.0 27440103 eCl@ss 8.0 27440103 10/13/2019   Page 7 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Classifications eCl@ss eCl@ss 9.0 27440102 ETIM ETIM 2.0 EC001297 ETIM 3.0 EC002061 ETIM 4.0 EC002061 ETIM 5.0 EC002061 ETIM 6.0 EC002061 UNSPSC UNSPSC 6.01 31251501 UNSPSC 7.0901 31251501 UNSPSC 11 31251501 UNSPSC 12.01 31251501 UNSPSC 13.2 39121413 Approvals Approvals Approvals UL Recognized / EAC / cULus Recognized Ex Approvals Approval details UL Recognized    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm     Nominal voltage UN 250 V Nominal current IN 4A mm²/AWG/kcmil 22  FILE E 118976 10/13/2019   Page 8 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Approvals EAC      B.01742 cULus Recognized    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm  E221474-20140616     Nominal voltage UN 250 V Nominal current IN 4A mm²/AWG/kcmil 22-20 Accessories Accessories Flat nut Flat nut - SACC-M16-NUT-VA - 1404983 Flat nut with M16 thread     Protective cap Sealing cap - PROT-M12 FS - 1560251 M12 sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     Sealing cap - PROT-M12 FS-M - 1430488 M12 metal sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     10/13/2019   Page 9 / 10 https://www.phoenixcontact.com/us/products/1405233 Flush-type connector - SACC-E-M12MS-4CON-M16/0,5 VA - 1405233 Accessories Seal Flat gasket - SACC-M16-SEAL CLM - 1430394 M16 flat gasket, for rear mounting of M12 flush-type connectors with M16 fastening thread     Phoenix Contact 2019 © - all rights reserved http://www.phoenixcontact.com 10/13/2019   Page 10 / 10