1409121

https://www.phoenixcontact.com/us/products/1409121 Crimp contact - CK1,0-ED-0,5ST AU - 1409121 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Crimp contact, Crimp contact, housing material: PA, min. conductor cross section: 0.14 mm², max. conductor cross section: 0.5 mm², Connection method: Crimp connection, Type of contact: Pin Key Commercial Data Packing unit 1 pc Minimum order quantity 100 pc GTIN GTIN 4046356619387 Weight per Piece (excluding packing) 0.400 g Custom tariff number 85389099 Country of origin Germany Technical data Ambient conditions Ambient temperature (operation) -40 °C ... 125 °C Mechanical characteristics Conductor cross section 0.14 mm² ... 0.5 mm² Connection cross section AWG 26 ... 20 Stripping length of the individual wire 4.5 mm Contact diameter 1 mm Insertion/withdrawal cycles ≥ 100 General Note For HC-MOT-AFL-SET 04/26/2020   Page 1 / 4 https://www.phoenixcontact.com/us/products/1409121 Crimp contact - CK1,0-ED-0,5ST AU - 1409121 Technical data General Connection method Crimp connection Contact type turned Material data Contact surface material gold-plated Contact carrier material PA Standards and Regulations Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. 04/26/2020   Page 2 / 4 https://www.phoenixcontact.com/us/products/1409121 Crimp contact - CK1,0-ED-0,5ST AU - 1409121 Technical data Standards and Regulations • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Operate the connector only when it is fully plugged in. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings Dimensional drawing Dimensional drawing Classifications eCl@ss eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27261200 eCl@ss 6.0 27261200 eCl@ss 7.0 27440204 eCl@ss 8.0 27440204 04/26/2020   Page 3 / 4 https://www.phoenixcontact.com/us/products/1409121 Crimp contact - CK1,0-ED-0,5ST AU - 1409121 Classifications eCl@ss eCl@ss 9.0 27440204 ETIM ETIM 4.0 EC000796 ETIM 5.0 EC000796 ETIM 6.0 EC000796 ETIM 7.0 EC000796 UNSPSC UNSPSC 6.01 31261502 UNSPSC 7.0901 31261502 UNSPSC 11 31261502 UNSPSC 12.01 31261502 UNSPSC 13.2 39121522 UNSPSC 18.0 39121522 UNSPSC 19.0 39121522 UNSPSC 20.0 39121522 UNSPSC 21.0 39121522 Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com 04/26/2020   Page 4 / 4