https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Flush-type connector, Universal, 4-position, Socket, M12, A-coded, Front mounting, M16 x 1.5, Individual wires,
cable length: 0.5 m
Your advantages
Easy-to-install, optimized XL housing contour with wrench size 19
Mechanical tightening limitation for long-term-stable gasket
Pre-assembled with litz wires for immediate use
Customer-specific assemblies and litz wire lengths available
Sealed on the litz wire side for optimum leak-tightness
All standard pin assignments and codings for signal, data, and power transmission with a uniform design-in design
For high transmission safety: shield connection to the housing with optional EMC nut
Key Commercial Data
Packing unit
1 pc
GTIN
GTIN
4046356936071
Weight per Piece (excluding packing)
20.000 g
Custom tariff number
85366990
Country of origin
Germany
Technical data
Dimensions
Length of cable
0.5 m
Ambient conditions
Ambient temperature (operation)
-25 °C ... 85 °C (Plug / socket)
11/06/2019 Page 1 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Technical data
Ambient conditions
Degree of protection
IP67
General
Note
The electrical and mechanical data specified assume that the connector
pair is correctly locked and mounted. If the connector is unlocked and if
there is a danger of contamination, the connector must be sealed using
a protective cap > IP54. Influences arising from litz wires, cables or PCB
assembly must also be taken into consideration.
Rated current at 40°C
4A
Rated voltage
250 V
Rated surge voltage
2.5 kV
Number of positions
4
Insulation resistance
≥ 100 MΩ
Coding
A - standard
Standards/regulations
M12 connector IEC 61076-2-101
Signal type/category
Universal
Status display
No
Overvoltage category
II
Degree of pollution
3
Connection method
Individual wires
Insertion/withdrawal cycles
> 100
Torque
0.8 Nm ... 1.3 Nm (Installation-side)
Mounting type
Front mounting M16 x 1.5 Tightening limitation
Material
Flammability rating according to UL 94
V0
Contact material
CuZn
Contact surface material
Au
Contact carrier material
PA 6.6
Material, knurls
Zinc die-cast, nickel-plated
Sealing material
FKM
Cable
Cable type
TPE litz wire
Conductor cross section
0.34 mm²
AWG signal line
22
Conductor structure signal line
7x 0.25 mm
Core diameter including insulation
1.2 mm ±0.07 mm
Thickness, insulation
0.21 mm (Core insulation)
Wire colors
brown, white, blue, black
11/06/2019 Page 2 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Technical data
Cable
Material conductor insulation
TPE
Conductor material
Tin-plated Cu litz wires
Standards/specifications
M12 connector IEC 61076-2-101
Insulation resistance
≥ 20 MΩ*km
Conductor resistance
≤ 57.6 mΩ/m
Nominal voltage, cable
300 V
Test voltage, cable
2000 V AC
Ambient temperature (operation)
-40 °C ... 85 °C (cable, fixed installation)
-25 °C ... 85 °C (cable, flexible installation)
Standards and Regulations
Standard designation
M12 connector
Standards/regulations
IEC 61076-2-101
Flammability rating according to UL 94
V0
CE safety note
WARNING: The connectors may not be plugged in or disconnected under
load. Ignoring the warning or improper use may damage persons and/or
property.
• WARNING: Commission properly functioning products only. The products
must be regularly inspected for damage. Decommission defective products
immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate
the product. They must observe the following safety notes. The qualified
personnel must be familiar with the basics of electrical engineering. They
must be able to recognize and prevent danger. The relevant symbol on the
packaging indicates that only personnel familiar with electrical engineering
are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and
electrical device engineering.
• When operating the connectors in outdoor applications, they must be
separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the
standards listed (e.g. the ones listed in the product accessories online at
phoenixcontact.com/products).
• When using the product in direct connection with third-party
manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must
be grounded
• Ensure that when laying the cable, the tensile load on the connectors
does not exceed the upper limit specified in the standards.
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
11/06/2019 Page 3 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Technical data
Standards and Regulations
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The
suitable accessories are available online in the accessory section of the
product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly
connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are
applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient
conditions, the surface of the connector can continue to warm up. In
this case, the user is responsible for posting warnings (e.g. DIN EN ISO
13732-1:2008-12).
Environmental Product Compliance
China RoHS
Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”, Category
“Manufacturer's declaration”
Drawings
11/06/2019 Page 4 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Dimensional drawing
M12 flush-type socket
11/06/2019 Page 5 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Circuit diagram
Contact assignment of the M12 socket
11/06/2019 Page 6 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Schematic diagram
Pin assignment M12 socket, 4-pos., A-coded, view female side
Classifications
eCl@ss
eCl@ss 10.0.1
27440102
eCl@ss 4.0
27140800
eCl@ss 4.1
27140800
eCl@ss 5.0
27143400
eCl@ss 5.1
27143400
eCl@ss 6.0
27279200
eCl@ss 7.0
27440103
11/06/2019 Page 7 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Classifications
eCl@ss
eCl@ss 8.0
27440103
eCl@ss 9.0
27440102
ETIM
ETIM 4.0
EC002061
ETIM 5.0
EC002061
ETIM 6.0
EC002061
UNSPSC
UNSPSC 13.2
39121413
Approvals
Approvals
Approvals
EAC / cULus Recognized
Ex Approvals
Approval details
EAC
B.01742
cULus Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm
E221474-20140616
Nominal voltage UN
250 V
Nominal current IN
4A
mm²/AWG/kcmil
22-20
Accessories
Accessories
Protective cap
11/06/2019 Page 8 / 9
https://www.phoenixcontact.com/us/products/1411568
Flush-type connector - SACC-E-M12FS-4P-M16XL/0,5 - 1411568
Accessories
Screw plug - PROT-M12 - 1680539
An M12 screw plug for the unoccupied M12 sockets of the sensor/actuator cable, boxes and flush-type connectors
Screw plug - PROT-M12 SH - 1503302
An M12 screw plug for the unoccupied M12 sockets of the shielded sensor/actuator cable, boxes and flush-type
connectors
Screw plug - PROT-M12 FB - 1555538
M12 high-grade steel screw plug, for unoccupied M12 sockets of the sensor/actuator cables, boxes and flush-type
connectors for the food industry
Flat nut - SACC-E-MU-M16 - 1504097
Flat nut with M16 thread
Phoenix Contact 2019 © - all rights reserved
http://www.phoenixcontact.com
11/06/2019 Page 9 / 9
