https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Bus system flush-type plug, PROFINET, 4-pos., M12 SPEEDCON, D-coded, rear/screw mounting with M16
thread, with 0.5 m TPE litz wire, 4 x 0.34 mm²
Your advantages
Easy-to-install, optimized XL housing contour with wrench size 19
Mechanical tightening limitation for long-term-stable gasket
Pre-assembled with litz wires for immediate use
Customer-specific assemblies and litz wire lengths available
Sealed on the litz wire side for optimum leak-tightness
All standard pin assignments and codings for signal, data, and power transmission with a uniform design-in design
For high transmission safety: shield connection to the housing with optional EMC nut
Key Commercial Data
Packing unit
1 pc
GTIN
GTIN
4046356935869
Weight per Piece (excluding packing)
20.000 g
Custom tariff number
85366990
Country of origin
Germany
Technical data
Dimensions
Length of cable
0.5 m
Ambient conditions
Ambient temperature (operation)
-25 °C ... 85 °C (Plug / socket)
05/17/2020 Page 1 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Technical data
Ambient conditions
Degree of protection
IP67
General
Note
The electrical and mechanical data specified assume that the connector
pair is correctly locked and mounted. If the connector is unlocked and if
there is a danger of contamination, the connector must be sealed using
a protective cap > IP54. Influences arising from litz wires, cables or PCB
assembly must also be taken into consideration.
This product corresponds to the PROFINET Cabling and Interconnection
Technology Guideline for PROFINET regulations, version 2.00, order
no: 2.252, Chapter 8.2 Connectors for Outside Environment (Balanced
cabling)
Rated current at 40°C
4A
Rated voltage
250 V
Rated surge voltage
2.5 kV
Number of positions
4
Insulation resistance
≥ 100 MΩ
Coding
D - data
Standards/regulations
M12 connector IEC 61076-2-101
Status display
No
Overvoltage category
II
Degree of pollution
3
Connection method
Individual wires
Insertion/withdrawal cycles
> 100
Torque
0.8 Nm ... 1.3 Nm (Installation-side)
Mounting type
Rear mounting M16 x 1.5 With flat nut
Assembly instructions
Tightening limitation
Material
Flammability rating according to UL 94
V0
Contact material
CuZn
Contact surface material
Au
Contact carrier material
PA 6.6
Material, knurls
Zinc die-cast, nickel-plated
Sealing material
FKM
Cable
Cable type
TPE litz wire
Conductor cross section
0.34 mm²
AWG signal line
22
Conductor structure signal line
7x 0.25 mm
05/17/2020 Page 2 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Technical data
Cable
Core diameter including insulation
1.2 mm ±0.07 mm
Thickness, insulation
0.21 mm
Wire colors
Yellow, orange, white, blue
Material conductor insulation
TPE
Conductor material
Tin-plated Cu litz wires
Standards/specifications
M12 connector IEC 61076-2-101
Insulation resistance
≥ 20 MΩ*km
Conductor resistance
≤ 57.6 mΩ/m
Transmission characteristics (category)
CAT5 (IEC 11801:2002)
Nominal voltage, cable
300 V
Test voltage, cable
2000 V AC
Ambient temperature (operation)
-40 °C ... 85 °C (cable, fixed installation)
-25 °C ... 85 °C (cable, flexible installation)
Standards and Regulations
Standards/specifications
M12 connector IEC 61076-2-101
Flammability rating according to UL 94
V0
Safety note
WARNING: The connectors may not be plugged in or disconnected under
load. Ignoring the warning or improper use may damage persons and/or
property.
• WARNING: Commission properly functioning products only. The products
must be regularly inspected for damage. Decommission defective products
immediately. Replace damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and operate
the product. They must observe the following safety notes. The qualified
personnel must be familiar with the basics of electrical engineering. They
must be able to recognize and prevent danger. The relevant symbol on the
packaging indicates that only personnel familiar with electrical engineering
are allowed to install and operate the product.
• The products are suitable for applications in plant, controller, and
electrical device engineering.
• When operating the connectors in outdoor applications, they must be
separately protected against environmental influences.
• Assembled products may not be manipulated or improperly opened.
• Only use mating connectors that are specified in the technical data of the
standards listed (e.g. the ones listed in the product accessories online at
phoenixcontact.com/products).
• When using the product in direct connection with third-party
manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector housings must
be grounded
• Ensure that when laying the cable, the tensile load on the connectors
does not exceed the upper limit specified in the standards.
05/17/2020 Page 3 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Technical data
Standards and Regulations
• Observe the corresponding technical data. You will find information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use. The
suitable accessories are available online in the accessory section of the
product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been properly
connected.
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are
applicable when combining several circuits in a cable and/or connector
• The connector warms up in normal operation. Depending on the ambient
conditions, the surface of the connector can continue to warm up. In
this case, the user is responsible for posting warnings (e.g. DIN EN ISO
13732-1:2008-12).
Environmental Product Compliance
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50 years
For details about hazardous substances go to tab “Downloads”, Category
“Manufacturer's declaration”
Drawings
05/17/2020 Page 4 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Dimensional drawing
M12 flush-type plug
05/17/2020 Page 5 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Dimensional drawing
Housing cutout for M16 fastening thread, mounting panel with thread
05/17/2020 Page 6 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Dimensional drawing
Housing cutout for M16 fastening thread, mounting panel with feed-through hole (alternatively with area as anti-rotation protection for panel thicknesses
> 2 mm up to max. 4.5 mm)
05/17/2020 Page 7 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Circuit diagram
Contact assignment of the M12 connector
05/17/2020 Page 8 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Schematic diagram
Pin assignment M12 male connector, 4-pos., D-coded, male side
Classifications
eCl@ss
eCl@ss 10.0.1
27440102
eCl@ss 4.0
27140800
eCl@ss 4.1
27140800
eCl@ss 5.0
27143400
eCl@ss 5.1
27143400
eCl@ss 6.0
27279200
eCl@ss 7.0
27440103
05/17/2020 Page 9 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Classifications
eCl@ss
eCl@ss 8.0
27440103
eCl@ss 9.0
27440102
ETIM
ETIM 4.0
EC002061
ETIM 5.0
EC002061
ETIM 6.0
EC002061
UNSPSC
UNSPSC 13.2
39121413
UNSPSC 18.0
39121413
UNSPSC 19.0
39121413
UNSPSC 20.0
39121413
UNSPSC 21.0
39121413
Approvals
Approvals
Approvals
EAC / cULus Recognized
Ex Approvals
Approval details
EAC
B.01687
cULus Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm
E221474-20140616
Nominal voltage UN
250 V
Nominal current IN
4A
mm²/AWG/kcmil
22-20
05/17/2020 Page 10 / 11
https://www.phoenixcontact.com/us/products/1411592
Bus system flat-type plug - SACC-DSI-M12MSD-4P-M16XL/0,5 - 1411592
Accessories
Accessories
Protective cap
Sealing cap - PROT-M12 FS - 1560251
M12 sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field
Sealing cap - PROT-M12 FS-M - 1430488
M12 metal sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the
field
Seal
Flat gasket - SACC-M16-SEAL CLM - 1430394
M16 flat gasket, for rear mounting of M12 flush-type connectors with M16 fastening thread
Phoenix Contact 2020 © - all rights reserved
http://www.phoenixcontact.com
05/17/2020 Page 11 / 11
