1415291

https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Flush-type connector, Power, 5-position, Plug, M12, K - Power, Front mounting, M16 x 1.5, Individual wires, cable length: 0.2 m, 2.50 mm², PEX litz wire Your advantages  For compact devices: transmit high power in a confined space  Easy-to-install, optimized XL housing contour with wrench size 19  Mechanical tightening limitation for long-term-stable gasket  Pre-assembled with litz wires for immediate use  Customer-specific assemblies and litz wire lengths available  Sealed on the litz wire side for optimum leak-tightness  For high transmission safety: shield connection to the housing with optional EMC nut Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626056203 Weight per Piece (excluding packing) 45.600 g Custom tariff number 85444290 Country of origin Germany Note Made to Order (non-returnable) Technical data Dimensions Length of cable 0.2 m Ambient conditions Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) -25 °C ... 85 °C (Plug / socket) Degree of protection IP67 12/03/2020   Page 1 / 6 https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Technical data General Note The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Rated current at 40°C 16 A Rated voltage 630 V Rated surge voltage 6 kV Number of positions 5 Insulation resistance ≥ 100 MΩ Coding K - Power Standards/regulations M12 connector IEC 61076-2-111 In line with Signal type/category Power Overvoltage category III Degree of pollution 3 Test voltage 6 kV Connection method Individual wires Insertion/withdrawal cycles > 100 Mounting type Front mounting M16 x 1.5 Tightening limitation Thread type M16 x 1.5 Halogen-free according to IEC 60754-1 Flame resistance in acc. with UL FT-2 Material Flammability rating according to UL 94 V0 Contact material CuZn Contact surface material Au Contact carrier material PA Material, knurls Zinc die-cast, nickel-plated Sealing material FKM Additional material specifications PU 2K (Grout material) Cable Cable type PEX litz wire Conductor cross section 2.5 mm² AWG signal line 14 Wire colors Black 1, black 2, black 3, black 4, green/yellow Material conductor insulation PE-X Conductor material Tin-plated Cu litz wires Standards/specifications M12 connector IEC 61076-2-111 In line with Test voltage Core/Core 6 kV Other resistance Hydrolysis-resistant Ambient temperature (operation) -40 °C ... 85 °C (without mechanical actuation) 12/03/2020   Page 2 / 6 https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Technical data Standards and Regulations Standards/specifications M12 connector IEC 61076-2-111 In line with Flame resistance in acc. with UL FT-2 Halogen-free according to IEC 60754-1 Other resistance Hydrolysis-resistant Flammability rating according to UL 94 V0 Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance 12/03/2020   Page 3 / 6 https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Technical data Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings Schematic diagram Dimensional drawing 28,2 PE 13 0,9 L 4 1 M12x1 M16x1,5 2 3 Connector pin assignment of M12 plug, 5-pos., K-coded, pin side view 19 2,8 M12 flush-type plug I [A] Diagram 27 24 21 18 15 12 9 6 3 0 1 1 0 2 = 4x2,5mm 10 20 30 40 50 60 70 80 90 100 110 120 130 [°C] I = current strength, T = ambient temperature Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 11.0 27440102 eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27143400 eCl@ss 6.0 27279200 eCl@ss 7.0 27440103 eCl@ss 8.0 27440103 eCl@ss 9.0 27440102 12/03/2020   Page 4 / 6 https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Classifications ETIM ETIM 5.0 EC002061 ETIM 6.0 EC002061 UNSPSC UNSPSC 13.2 39121413 UNSPSC 18.0 39121413 UNSPSC 19.0 39121413 UNSPSC 20.0 39121413 UNSPSC 21.0 39121413 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC      B.01687 Accessories Accessories Flat nut Flat nut - SACC-E-MU-M16 - 1504097 Flat nut with M16 thread     Protective cap 12/03/2020   Page 5 / 6 https://www.phoenixcontact.com/za/products/1415291 Flush-type connector - SACC-E-M12MSK-4PE-M16XL/0,2 - 1415291 Accessories Sealing cap - PROT-M12 FS - 1560251 M12 sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     Sealing cap - PROT-M12 FS-M - 1430488 M12 metal sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com 12/03/2020   Page 6 / 6