1416716

FOC-M12-MNNA-TC... M12 FO transceivers Data sheet 103995_en_02 1 © PHOENIX CONTACT 2015-01-28 Description The FO transceiver is available in two versions. – FOC-M12-MNNA-TC-1300 for applications with 50/125 μm, 62.5/125 μm or 200/230 μm fibers – FOC-M12-MNNA-TC-650 for applications with 980/1000 μm fibers The FO transceiver features a high-speed transmitter and receiver circuit with a 1310 nm or 650 nm optical wavelength at high optical power. This makes the M12 transceiver an ideal alternative in data transmission systems with fiber optics. An I2C interface ensures that the transceiver is efficiently monitored and managed. Due to the high data transmission rate of 125 Mbps, the optical characteristics, and connection technology for the fiber optics, the M12 transceiver offers a wealth of application options: – Optical networks – Fast Ethernet – Industrial electronics – Power electronics 1.1 – – – – – – – – – Properties 125 Mbps +3.3 V power supply PECL inputs/outputs Signal Detect (SD) output I2C management interface Metal housing Pin connector pattern in accordance with 61754-27 Ambient temperature: -40°C... +85 °C RoHS-compliant FOC-M12-MNNA-TC-1300 – – – – 1310 nm wavelength -19°dBm output power (50/125 μm) -30 dBm receiver sensitivity Suitable for 50/125 μm, 62.5/125 μm and 200/230 μm FOC-M12-MNNA-TC-650 – – – – 650 nm wavelength -4 dBm output power (980/1000 μm) -20 dBm receiver sensitivity Suitable for 980/1000 μm To optimize transmission performance and to achieve the maximum transmission path, correctly pre-assembled fiber optic connectors are required. Loads that exceed the specified limit values can cause permanent damage to the component. The limit values represent the load limits of the component. Make sure you always use the latest documentation. It can be downloaded at phoenixcontact.net/products. This data sheet is valid for all products listed on the following page: FOC-M12-MNNA-TC... 2 Ordering data Fiber optic transceiver Description Order No. Pcs. / Pkt. M12 FO transceiver, duplex, wavelength: 650 nm for 125 Mbps, for POF and FOC-M12-MNNA-TC-650 PCF fibers, for PCB mounting, M16 fastening thread, with sealing cap, including I²C interface for transceiver monitoring and management Type 1416716 1 M12 FO transceiver, duplex, wavelength: 1300 nm for 125 Mbps, for GOF fi- FOC-M12-MNNA-TC-1300 bers, for PCB mounting, M16 fastening thread, with sealing cap, including I²C interface for transceiver monitoring and management 1416729 1 Accessories Description Type Order No. Pcs. / Pkt. M12 fiber optic coupler, duplex, suitable for all fibers, with wall bracket, IP65 degree of protection FOC-M12-BU/BU 1416677 1 Assembled FO cable, round cable, 980/1000 μm POF fibers, for in- 1 m stallation inside buildings 2m M12 FO to M12 FO 5m FOC-PN-B-1000/M12-C/SCRJ/1 1408865 1 FOC-PN-B-1000/M12-C/SCRJ/2 1408864 1 FOC-PN-B-1000/M12-C/SCRJ/5 1416648 1 Assembled FO cable, round cable, 980/1000 μm POF fibers, for in- 1 m stallation inside buildings 2m M12 FO to SCRJ/IP20 5m FOC-PN-B-1000/M12-C/M12-C/1 1408871 1 FOC-PN-B-1000/M12-C/M12-C/2 1408870 1 FOC-PN-B-1000/M12-C/M12-C/5 1416680 1 Assembled FO cable, round cable, 200/230 μm PCF-GI fibers, for installation inside buildings 1m FOC-HCS-GI-1005/M12-C/M12-C/1 1408873 1 2m FOC-HCS-GI-1005/M12-C/M12-C/2 1408872 1 M12 FO to M12 FO 5m FOC-HCS-GI-1005/M12-C/M12-C/5 1416693 1 Assembled FO cable, round cable, 200/230 μm PCF-GI fibers, for installation inside buildings 1m FOC-HCS-GI-1005/M12-C/SCRJ/1 1408867 1 2m FOC-HCS-GI-1005/M12-C/SCRJ/2 1408866 1 M12 FO to SCRJ/IP20 5m FOC-HCS-GI-1005/M12-C/SCRJ/5 1416651 1 Assembled FO cable, round cable, 50/125 μm GOF-MM fibers, for installation inside buildings 1m FOC-M12-M12-GB02/2 1408874 1 2m FOC-M12-M12-GB02/1 1408875 1 M12 FO to M12 FO 5m FOC-M12-M12-GB02/5 1416703 1 Assembled FO cable, round cable, 50/125 μm GOF-MM fibers, for installation inside buildings 1m FOC-M12-LC:A-GB02/1 1408869 1 2m FOC-M12-LC:A-GB02/2 1408868 1 M12 FO to LC duplex 5m FOC-M12-LC:A-GB02/5 1416664 1 3 Limit values Loads that exceed the limit values can cause permanent damage to the component. The limit values represent the load limits of the component. Continuous operation with these values is not recommended, as this may jeopardize the reliability of the component. The FO transceiver, connectors, and couplings should only be mounted finger tight. Limit values Operating temperature -40 °C ... +85°C Storage temperature -40 °C ... +100°C Soldering temperature 2 mm from housing, t  5 s 260°C Supply voltage 4V Data input voltage -0.5 V ... 4 V Differential input voltage 2 V (peak-to-peak with FOC-M12-MNNA-TC-1300) PECL output current -50 mA ... +50 mA Electrostatic air discharge in acc. with EN 61000-6-2 8 kV Electrostatic contact discharge in acc. with EN 61000-6-2 4 kV Immunity of electrical field in accordance with EN 61000-6-2 10 V/m 2/8 PHOENIX CONTACT 103995_en_02 FOC-M12-MNNA-TC... 4 Technical data General data Storage temperature -40 °C ... 100 °C Ambient temperature -40 °C ... 85 °C Supply voltage 3 V ... 3.6 V, typical 3.3 V Differential input voltage 1 V ... 1.8 V, typical 1.4 V Current carrying capacity 50 Ω Data rate 125 Mbps Humidity 5 % ... 95 % Transmitter FOC-M12-MNNA-TC-650 FOC-M12-MNNA-TC-1300 Maximum wavelength λmax 625 nm ... 675 nm, typical 650 nm 1280 nm ... 1340 nm, typical 1310 nm Average optical output voltage -8 dBm ... -5 dBm -21 dBm ... -18 dBm 980/1000 μm, 50 % DC, NA 0.5 50/125 μm, 50 % DC, NA 0.2 Current consumption 70 mA ... 80 mA 90 mA ... 120 mA Rise time 2.5 ns 1.8 ns 1.8 ns Fall time 2.5 ns Data input current for logical “0” at least -50 μA at least -50 μA Data input current for logical “1” maximum +50 μA maximum +50 μA Data input voltage for logical “0” -1.81 V ... -1.475 V -1.81 V ... -1.475 V Data input voltage for logical “1” -1.165 V ... -0.88 V -1.165 V ... -0.88 V Receiver FOC-M12-MNNA-TC-650 FOC-M12-MNNA-TC-1300 Maximum receiver sensitivity -25 dBm -31 dBm Maximum input power At least 2 dBm at least -3 dBm Current consumption 70 mA ... 80 mA 70 mA ... 80 mA (no load) Threshold value for signal detection -20 dBm -29.2 dBm Signal detection hysteresis 1.5 dB ... 6 dB, typical 3 dB 1.5 dB ... 5 dB, typical 2.5 dB Maximum response time, signal detection 10 μs 10 μs Maximum fall time, signal detection 10 μs 10 μs Signal detection output voltage log. 0 -1.83 V ... -1.55 V -1.83 V ... -1.55 V Signal detection output voltage log. 1 -1.08 V ... -0.88 V -1.08 V ... -0.88 V Data output voltage log. 0 -1.83 V ... -1.55 V -1.83 V ... -1.55 V Data output voltage log. 1 -1.08 V ... -0.88 V -1.08 V ... -0.88 V Data output rise time 20 % ... 80 % 2.2 ns 2.2 ns Data output fall time 80 % ... 20 % 2.2 ns 2.2 ns Bit error rate