1417382

https://www.phoenixcontact.com/us/products/1417382 Contact insert module - HC-M-01-AT-M-40-PE - 1417382 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Key Commercial Data Packing unit 1 STK Minimum order quantity 2 STK GTIN GTIN 4055626112633 Custom tariff number 85366990 Country of origin Poland Technical data Dimensions Height 54.6 mm Width 34.4 mm Length 29.3 mm Electrical characteristics Note For HEAVYCON HC-B6 to B48 housing (housing height: min. 72 mm), HCM-MHR... hinged retaining frame required, axial connection for 5 mm Allen key Rated current 200 A Connection profile PE Ambient conditions Ambient temperature (operation) -40 °C ... 125 °C 04/10/2017   Page 1 / 4 https://www.phoenixcontact.com/us/products/1417382 Contact insert module - HC-M-01-AT-M-40-PE - 1417382 Technical data Mechanical characteristics Conductor cross section 25 mm² ... 70 mm² (The cross section specification refers to the geometric cross section of the cable used) Connection cross section AWG 3 ... 00 Stripping length of the individual wire 16 mm Tightening torque 8 Nm (25 mm² ... 70 mm²) 9 Nm (70 mm²) Wire diameter including insulation 12 mm (25 mm²) 16 mm (40 mm²) Hexagonal socket WAF 5 Insertion/withdrawal cycles ≥ 500 Minimum housing height 72 mm General Series HC-M-HS Color light gray Number of module slots 2 Connection method Axial screw connection Flammability rating according to UL 94 V0 Assembly instructions - Use only flexible conductors, - Connection of wires with 5 mm an Allen wrench, - Housing height h ≥ 72 mm, - Connectors may only be operated without load/voltage. Connection Note on axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Use of cables with a geometric cross section that differs greatly from the nominal cross section of the cable should be checked before use. The wiring space for axial screw technology is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) should be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is turned back all the way (chamber is open). The cables must not be twisted. The wires should be inserted as far as they will go into the contact chamber (until the insulation touches the contact). Hold the wires in position and use the socket wrench to tighten. The used wire end should be cut off before connecting again. The connection screw may only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable should be mechanically intercepted at an appropriate distance from the connection point (e.g., by using a plate cutout). DIN VDE 0100-520:2003-06 contains information on how to do this correctly. The module cannot be used simultaneously with HC-B..-TMB-SD-IP65 and HCB..-TMS-SD-IP65 protective covers. PE mounting plate The PE plate must be pressed hard against the swing frame using the 4 screws. First loosen the 4 screws of the PE plate and then tighten them again once the module is fixed in the swing frame. 04/10/2017   Page 2 / 4 https://www.phoenixcontact.com/us/products/1417382 Contact insert module - HC-M-01-AT-M-40-PE - 1417382 Technical data Material data Contact material Copper alloy Contact surface material Ag Contact carrier material PC Standards and Regulations Flammability rating according to UL 94 V0 Drawings Dimensional drawing Diagram 400 Operating current [A] 54,6 34,4 5 29,3 350 300 2 250 200 150 1 100 1 = 50 mm2 50 0 Male insert 2 = 70 mm2 0 20 40 60 80 100 120 Ambient temperature [°C] Three modules in B24 housing Diagram Schematic diagram Operating current [A] 400 350 2 300 250 200 150 1 100 50 0 Axial screw connection 1 = 50 mm2 2 = 70 mm2 0 20 40 60 80 100 120 Ambient temperature [°C] Two modules in B24 housing Approvals Approvals Approvals EAC 04/10/2017   Page 3 / 4 https://www.phoenixcontact.com/us/products/1417382 Contact insert module - HC-M-01-AT-M-40-PE - 1417382 Approvals Ex Approvals Approval details EAC      7500651.22.01.00246 Phoenix Contact 2017 © - all rights reserved http://www.phoenixcontact.com 04/10/2017   Page 4 / 4