1419328

https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Flush-type socket, shielded, 5-pos., M12, A-coded, rear/screw mounting with M16 thread, with 1 m line, 5 x 0.34 mm² Your advantages  Pre-assembled with cables in various standard lengths for immediate use  Customer-specific assemblies and cable lengths can be supplied  Sealed on the cable side for optimum tightness of seal  For high transmission safety: shield connection to the housing with optional EMC nut Key Commercial Data Packing unit 1 pc GTIN GTIN 4046356533294 Weight per Piece (excluding packing) 80.000 g Custom tariff number 85444290 Country of origin Germany Technical data Dimensions Length of cable 1m Ambient conditions Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) Degree of protection IP67 (When plugged in) IP65 (When plugged in) 11/06/2019   Page 1 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Technical data General Note The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. Rated current at 40°C 4A Rated voltage 60 V Rated surge voltage 1.5 kV Number of positions 5 Insulation resistance ≥ 100 MΩ Coding A - standard Standards/regulations M12 connector IEC 61076-2-101 Status display No Overvoltage category II Degree of pollution 3 Connection method Individual wires Insertion/withdrawal cycles > 100 Torque 2 Nm ... 3 Nm (Installation-side) Mounting type Rear mounting M16 x 1.5 With flat nut Material Flammability rating according to UL 94 V0 Contact material CuZn Contact surface material Au Contact carrier material PA 6.6 Material, knurls Zinc die-cast, nickel-plated Sealing material FKM Cable Cable type PUR halogen-free black Cable type (abbreviation) PUR Cable abbreviation LiF9YC11Y Conductor cross section 5x 0.34 mm² (Signal line) AWG signal line 22 Conductor structure signal line 42x 0.10 mm Core diameter including insulation 1.27 mm ±0.02 mm (Signal line) Thickness, insulation approx. 0.21 mm (Core insulation) approx. 0.8 mm (Outer cable sheath) Wire colors Brown, white, blue, black, gray Overall twist 5 wires around filler to the core 11/06/2019   Page 2 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Technical data Cable Shielding Braided copper wires Optical shield covering 80 % External sheath, color black-gray RAL 7021 External cable diameter D 5.25 mm ±0.2 mm Smallest bending radius, fixed installation 26 mm Smallest bending radius, movable installation 52 mm (up to +60°C) Number of bending cycles 10000000 Bending radius 52 mm Traversing path 10 m Traversing rate 3 m/s Acceleration 10 m/s² Cable weight 48 kg/km Outer sheath, material PUR Conductor material Bare Cu litz wires Standards/specifications M12 connector IEC 61076-2-101 Insulation resistance 70 GΩ*km (at 20 °C) Conductor resistance max. 57 Ω/km (at 20 °C) Nominal voltage, cable 300 V (at 20 °C) Test voltage, cable 3000 V Test voltage Core/Core 3000 V (at 20 °C) Special properties Flexible cable conduit capable Ambient temperature (operation) -40 °C ... 85 °C (cable, fixed installation) -25 °C ... 85 °C (cable, flexible installation) Standards and Regulations Standard designation M12 connector Standards/regulations IEC 61076-2-101 Flammability rating according to UL 94 V0 CE safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. 11/06/2019   Page 3 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Technical data Standards and Regulations • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings 11/06/2019   Page 4 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Dimensional drawing Housing cutout for M16 fastening thread, mounting panel with feed-through hole (alternatively with surface as protection against rotation) 11/06/2019   Page 5 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Dimensional drawing M12 flush-type connector 11/06/2019   Page 6 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Circuit diagram Contact assignment of the M12 socket 11/06/2019   Page 7 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Schematic diagram Pin assignment M12 socket, 5-pos., A-coded, socket side view 11/06/2019   Page 8 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Cable cross section PUR halogen-free black [PUR] Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27143400 eCl@ss 6.0 27279200 eCl@ss 7.0 27440103 11/06/2019   Page 9 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Classifications eCl@ss eCl@ss 8.0 27440103 eCl@ss 9.0 27440102 ETIM ETIM 2.0 EC001297 ETIM 3.0 EC002061 ETIM 4.0 EC002061 ETIM 5.0 EC002061 ETIM 6.0 EC002061 UNSPSC UNSPSC 6.01 31251501 UNSPSC 7.0901 31251501 UNSPSC 11 31251501 UNSPSC 12.01 31251501 UNSPSC 13.2 39121413 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC      B.00767 Accessories Accessories Plug for cable screw gland 11/06/2019   Page 10 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Accessories Screw plug - SACC-M16-SEALING PLUG SET - 1453368 M16 screw plug for unused M12 housing cutouts     Protective cap Screw plug - PROT-M12 - 1680539 An M12 screw plug for the unoccupied M12 sockets of the sensor/actuator cable, boxes and flush-type connectors     Screw plug - PROT-M12 SH - 1503302 An M12 screw plug for the unoccupied M12 sockets of the shielded sensor/actuator cable, boxes and flush-type connectors     Screw plug - PROT-M12 FB - 1555538 M12 high-grade steel screw plug, for unoccupied M12 sockets of the sensor/actuator cables, boxes and flush-type connectors for the food industry     Seal Flat gasket - SACC-M16-SEAL CLM - 1430394 M16 flat gasket, for rear mounting of M12 flush-type connectors with M16 fastening thread     11/06/2019   Page 11 / 12 https://www.phoenixcontact.com/us/products/1419328 Flush-type connector - SACCBP-FS-5CON-M16/1,0-PUR SCO - 1419328 Accessories Phoenix Contact 2019 © - all rights reserved http://www.phoenixcontact.com 11/06/2019   Page 12 / 12