SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user
documentation. Our general terms of use for downloads are valid.
Contact carrier, 5-position, Pin, straight, M12, coding: A, Front mounting, Square flange, Crimp connection, 0.34 mm2, Item is lead-free
in accordance with RoHS II without Exemption 6c (Pb IP54.
Influences arising from litz wires, cables or PCB assembly must
also be taken into consideration.
Safety note
Safety note
WARNING: The connectors may not be plugged in or
disconnected under load. Ignoring the warning or improper use
may damage persons and/or property.
• WARNING: Commission properly functioning products only.
The products must be regularly inspected for damage.
Decommission defective products immediately. Replace
damaged products. Repairs are not possible.
• WARNING: Only electrically qualified personnel may install and
operate the product. They must observe the following safety
notes. The qualified personnel must be familiar with the basics of
electrical engineering. They must be able to recognize and
prevent danger. The relevant symbol on the packaging indicates
that only personnel familiar with electrical engineering are
allowed to install and operate the product.
• The products are suitable for applications in plant, controller,
and electrical device engineering.
• When operating the connectors in outdoor applications, they
must be separately protected against environmental influences.
• Assembled products may not be manipulated or improperly
opened.
• Only use mating connectors that are specified in the technical
data of the standards listed (e.g. the ones listed in the product
accessories online at phoenixcontact.com/products).
• When using the product in direct connection with third-party
manufacturers, the user is responsible.
• For operating voltages > 50 V AC, conductive connector
housings must be grounded
• Ensure that when laying the cable, the tensile load on the
connectors does not exceed the upper limit specified in the
standards.
• Observe the corresponding technical data. You will find
information:
o On the product
o On the packing label
o In the supplied documentation
o Online at phoenixcontact.com/products under the product
• Only use tools recommended by Phoenix Contact
• Use a protective cap to protect connectors that are not in use.
The suitable accessories are available online in the accessory
section of the product at phoenixcontact.com/products
• Ensure that the protective or functional ground has been
properly connected.
Jan 8, 2024, 10:04 AM
Page 2 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
• VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3
are applicable when combining several circuits in a cable and/or
connector
• The connector warms up in normal operation. Depending on the
ambient conditions, the surface of the connector can continue to
warm up. In this case, the user is responsible for posting
warnings (e.g. DIN EN ISO 13732-1:2008-12).
Product properties
Number of positions
5
No. of cable outlets
1
Seal present
no
Shielded
no
Coding
A
Thread type
M12
Insulation characteristics
Overvoltage category
II
Degree of pollution
3
Electrical properties
Rated surge voltage
1.5 kV
Contact resistance
≤ 3 mΩ
Insulation resistance
≥ 100 MΩ
Nominal voltage UN
60 V
Nominal current IN
4A
Connection data
Connection method
Crimp connection
Signaling
Status display
No
Status display present
No
Material specifications
Flammability rating according to UL 94
V0
Contact carrier material
PA 6.6
Connector
Connection 1
Head design
Pin
Head cable outlet
straight
Head thread type
M12
Coding
A
Cable/line
Jan 8, 2024, 10:04 AM
Page 3 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Cable cross section
0.34 mm²
Ambient temperature (operation)
-40 °C ... 85 °C (cable, fixed installation)
-25 °C ... 85 °C (Cable, flexible installation)
Mechanical properties
Mechanical data
Insertion/withdrawal cycles
> 100
Environmental and real-life conditions
Ambient conditions
Degree of protection
IP67
IP67
Ambient temperature (operation)
-25 °C ... 85 °C (Plug / socket)
-40 °C ... 85 °C (without mechanical actuation)
-25 °C ... 85 °C (Cable, flexible installation)
-40 °C ... 85 °C (cable, fixed installation)
Standards and regulations
M12
Standard designation
M12 connector
Standards/specifications
IEC 61076-2-101
Mounting
Mounting type
Front mounting Square flange 25 mm side length
Assembly instructions
25 mm side length
Connection method
Crimp connection
Jan 8, 2024, 10:04 AM
Page 4 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Drawings
I [A]
Diagram
9
8
7
6
5
4
3
2
1
0
1
1
0
2
= 5x0,34mm
10 20 30 40 50 60 70 80 90 100 110 120 130
[°C]
I = current strength, T = ambient temperature
Dimensional drawing
17
Ø9,4
Ø
Ø 11
10 ,7
,1
18,04
Dimensional drawing
Jan 8, 2024, 10:04 AM
Page 5 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Circuit diagram
1
BN
2
WH
4
BK
3
BU
5
GY
Schematic diagram
4
3
5
1
2
Pin assignment M12 male connector, 5-pos., A-coded, male side
Jan 8, 2024, 10:04 AM
Page 6 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Classifications
ECLASS
ECLASS-11.0
27440223
ECLASS-12.0
27440116
ECLASS-13.0
27440223
ETIM
ETIM 9.0
EC003557
UNSPSC
UNSPSC 21.0
39121400
Jan 8, 2024, 10:04 AM
Page 7 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Environmental product compliance
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
No hazardous substances above threshold values
Jan 8, 2024, 10:04 AM
Page 8 (9)
SACC-MCI-M12MS-5CON - Contact carrier
1419988
https://www.phoenixcontact.com/pc/products/1419988
Accessories
CC-1,0-ST-0,34-MS AU - Crimp contact
1452356
https://www.phoenixcontact.com/pc/products/1452356
Crimp contact, Pin, turned, contact
diameter: 1 mm, crimp range: 0.08
mm2 ... 0.5 mm2, Alternative product
in accordance with RoHS II without
Exemption 6c (Pb