1420019

SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user documentation. Our general terms of use for downloads are valid. Device connector, rear mounting, Power, 4-position, Socket, straight, M12, coding: S, on free cable end, Rear mounting, M16 x 1.5, Individual wires, cable length: 4.5 m, 1.31 mm2, UL/cUL stranded hook-up wire, Alternative product in accordance with RoHS II without Exemption 6c  (Pb  IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. General Lock nut is included in the scope of delivery General Contact connection method: Crimp connection Safety note Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. Jan 8, 2024, 10:04 AM Page 2 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Mounting Mounting type Rear mounting M16 x 1.5 With flat nut Assembly instructions With flat nut Connection method Individual wires Product properties Product type Circular connectors (device side) Sensor type Power Number of positions 4 No. of cable outlets 1 Shielded no Coding S Thread type M12 Insulation characteristics Overvoltage category III Degree of pollution 3 Material specifications Flammability rating according to UL 94 V0 Seal material FKM Contact material CuZn Contact surface material Au Contact carrier material PA Material for screw connection Zinc die-cast, nickel-plated Conductor material Bare Cu litz wires Electrical properties Rated voltage in acc. with IEC 61076-2-101 630 V Rated surge voltage 6 kV 6 kV AC Contact resistance ≤ 3 mΩ Insulation resistance ≥ 100 MΩ Nominal voltage UN 630 V Jan 8, 2024, 10:04 AM Page 3 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Nominal current IN 12 A Test voltage 6 kV Connection data Conductor connection Connection method Individual wires Contact connection type Socket Conductor cross section 1.31 mm² Tightening torque 3 Nm 4 Nm Mechanical properties Mechanical data Insertion/withdrawal cycles > 100 Connector Connection 1 Head design Socket Head cable outlet straight Head thread type M12 Coding S Connection 2 Head design free cable end Cable/line Cable length 4.5 m Cable type UL/cUL stranded hook-up wire Signal type/category Power Wire diameter incl. insulation 2.2 mm Single wire, color black 1, black 2, black 3, green/yellow Cable cross section 1.31 mm² Conductor material Bare Cu litz wires AWG signal line 16 Material wire insulation mPPE Halogen-free yes Flame resistance in acc. to UL 1581 VW1 Ambient temperature (operation) -40 °C ... 105 °C (cable, fixed installation) -20 °C ... 105 °C (Cable, flexible installation) Environmental and real-life conditions Ambient conditions Jan 8, 2024, 10:04 AM Page 4 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Degree of protection IP67 IP65/IP67 Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) -20 °C ... 105 °C (Cable, flexible installation) -40 °C ... 105 °C (cable, fixed installation) Standards and regulations Flame resistance in acc. to UL 1581 VW1 M12 Standard designation M12 connector Standards/specifications IEC 61076-2-111 Note In line with Jan 8, 2024, 10:04 AM Page 5 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Drawings Schematic diagram 5 3 2 1 Pin assignment of M12 socket, 4-pos., S-coded, socket side view I [A] Diagram 27 24 21 18 15 12 9 6 3 0 1 1 0 2 = 3x1,5mm 10 20 30 40 50 60 70 80 90 100 110 120 130 [°C] I = current strength, T = ambient temperature Jan 8, 2024, 10:04 AM Page 6 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Circuit diagram 1 BK1 2 BK2 3 BK3 4 GN/YE Dimensional drawing 24,1 L 2,8 8 M12x1 M16x1,5 2,8 22,6 17 3 19 Dimensional drawing Jan 8, 2024, 10:04 AM Page 7 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Approvals To download certificates, visit the product detail page: https://www.phoenixcontact.com/us/products/1420019   cUL Recognized Approval ID: E468743-20190917 Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2 600 V 12 A - 16 - Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2 600 V 12 A - 16 - UL Recognized Approval ID: E468743-20190917 cULus Recognized Jan 8, 2024, 10:04 AM Page 8 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Classifications ECLASS ECLASS-11.0 27440102 ECLASS-12.0 27440116 ECLASS-13.0 27440116 ETIM ETIM 8.0 EC002635 UNSPSC UNSPSC 21.0 39121400 Jan 8, 2024, 10:04 AM Page 9 (10) SACC-DSI-M12FSS-4CON-M16/4,5PE - Device connector, rear mounting 1420019 https://www.phoenixcontact.com/us/products/1420019 Environmental product compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads” Phoenix Contact 2024 © - all rights reserved https://www.phoenixcontact.com Phoenix Contact USA 586 Fulling Mill Road Middletown, PA 17057, United States (+717) 944-1300 info@phoenixcon.com Jan 8, 2024, 10:04 AM Page 10 (10)