1440931

https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) 4-pos. contact carrier, with splice ring, A-coded The figure shows the 4-pos. version of the product Your advantages  Convenient field assembly: device connectors for fast on-site mounting  Contact carriers that can be freely assembled or available with pre-assembled litz wires  Standard pin assignments for signal and power transmission with a uniform design-in design Key Commercial Data Packing unit 1 pc Minimum order quantity 10 pc GTIN GTIN 4046356533775 Weight per Piece (excluding packing) 2.000 g Custom tariff number 85366990 Country of origin Germany Technical data Ambient conditions Ambient temperature (operation) -25 °C ... 85 °C (Plug / socket) Degree of protection IP67 General Rated current at 40°C 4A 11/06/2019   Page 1 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Technical data General Rated voltage 250 V Rated surge voltage 2.5 kV Number of positions 4 Insulation resistance ≥ 100 MΩ Coding A - standard Standards/regulations M12 connector IEC 61076-2-101 Status display No Overvoltage category II Degree of pollution 3 Connection method Crimp contacts Mounting type Front mounting Square flange 25 mm side length Material Flammability rating according to UL 94 V0 Contact carrier material PA 6.6 Cable Conductor cross section 0.34 mm² Standards/specifications M12 connector IEC 61076-2-101 Standards and Regulations Standard designation M12 connector Standards/regulations IEC 61076-2-101 Flammability rating according to UL 94 V0 CE safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. 11/06/2019   Page 2 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Technical data Standards and Regulations • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings 11/06/2019   Page 3 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Dimensional drawing Contact carrier and insulating body Circuit diagram Contact assignment of the M12 plug 11/06/2019   Page 4 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Schematic diagram Pin assignment M12 plug, 4-pos., A-coded, view plug side Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27143400 eCl@ss 6.0 27279200 eCl@ss 7.0 27440103 11/06/2019   Page 5 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Classifications eCl@ss eCl@ss 8.0 27440103 eCl@ss 9.0 27440102 ETIM ETIM 4.0 EC002061 ETIM 5.0 EC002061 ETIM 6.0 EC002061 UNSPSC UNSPSC 6.01 31251501 UNSPSC 7.0901 31251501 UNSPSC 11 31251501 UNSPSC 12.01 31251501 UNSPSC 13.2 39121413 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC      B.01742 Accessories Accessories Crimp contact 11/06/2019   Page 6 / 7 https://www.phoenixcontact.com/us/products/1440931 Contact carriers - SACC-MCI-M12MS-4CON - 1440931 Accessories Crimp contact - CC-1,0-ST-0,34-MS AU - 1452356 Crimp contact, diameter 1 mm, for all 3 to 5-pos. contact inserts, crimp range from 0.08 mm² - 0.34 mm².     Panel mounting base Flange - SACC-MSQ-M12MS-25-3,2 SCO - 1419959 Flange housing, 25 mm x 25 mm     Protective cap Sealing cap - PROT-M12 FS - 1560251 M12 sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     Sealing cap - PROT-M12 FS-M - 1430488 M12 metal sealing cap for unoccupied M12 plugs of the sensor/actuator cable, flush-type plugs and I/O devices in the field     Phoenix Contact 2019 © - all rights reserved http://www.phoenixcontact.com 11/06/2019   Page 7 / 7