1607322

https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Contact insert set for mounting side, sleeve frame with PE, 4 fixing screws, 2-pos. contact inserts preassembled, 6 coding profiles, 2 mounting flanges The figure shows the 8-position version Your advantages  Compact design  Universal connection  Proven COMBICON technology  Can be keyed to prevent incorrect connection Key Commercial Data Packing unit 1 pc Minimum order quantity 5 pc GTIN GTIN 4017918941055 Weight per Piece (excluding packing) 55.980 g Custom tariff number 85366990 Country of origin Poland Technical data General Note Connectors may only be connected/disconnected when under no load. Connection technology Screw connection Connection method Screw connection Tightening torque 0.5 Nm ... 0.6 Nm 05/30/2020   Page 1 / 6 https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Technical data General Degree of pollution 3 Number of positions 7+PE Insertion/withdrawal cycles ≥ 50 Size VC3 Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 4 mm² Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 4 mm² Conductor cross section 0.2 mm² ... 4 mm² Connection cross section AWG 30 ... 10 Stripping length of the individual wire 7 mm Ambient conditions Ambient temperature (operation) -40 °C ... 100 °C Material data Housing material PA Contact material CuZn Contact surface material Tin-plated Contact carrier material PA Electrical characteristics Rated voltage (III/3) 400 V Nominal voltage UN 400 V Rated surge voltage 6 kV 6 kV Rated current 20 A 20 A Standards and Regulations Flammability rating according to UL 94 V0 Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the 05/30/2020   Page 2 / 6 https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Technical data Standards and Regulations packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Operate the connector only when it is fully plugged in. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings 05/30/2020   Page 3 / 6 https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Dimensional drawing Contact insert 05/30/2020   Page 4 / 6 https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Dimensional drawing Mounting cutout Classifications eCl@ss eCl@ss 10.0.1 27440205 eCl@ss 4.0 27260700 eCl@ss 4.1 27260700 eCl@ss 5.0 27260700 eCl@ss 5.1 27261200 eCl@ss 6.0 27261200 eCl@ss 7.0 27440205 eCl@ss 8.0 27440205 eCl@ss 9.0 27440205 ETIM ETIM 2.0 EC001121 ETIM 3.0 EC001121 ETIM 4.0 EC001121 ETIM 5.0 EC000438 ETIM 6.0 EC000438 ETIM 7.0 EC000438 05/30/2020   Page 5 / 6 https://www.phoenixcontact.com/us/products/1607322 Contact insert set - VC-AR3/4M-S2222-SET - 1607322 Classifications UNSPSC UNSPSC 6.01 30211923 UNSPSC 7.0901 39121522 UNSPSC 11 39121522 UNSPSC 12.01 39121522 UNSPSC 13.2 39121522 UNSPSC 18.0 39121522 UNSPSC 19.0 39121522 UNSPSC 20.0 39121522 UNSPSC 21.0 39121522 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC      B.01687 Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com 05/30/2020   Page 6 / 6