1619209

https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Device connector, front mounting, straight, for standard and SPEEDCON interlock, M17, number of positions: 3+PE, type of contact: Pin, Crimp connection, Axial O-ring, 4x Ø 3.2, shielded: yes, flange dimensions: 25.75 mm x 25.75 mm The figure shows the 4-pos. socket version Your advantages  Consistent EMC protection for reliable connection solutions in the industrial environment  Crimping connection: vibration- and temperature-resistant assembly  Flexible mounting, thanks to snap-in contact inserts Key Commercial Data Packing unit 1 pc GTIN GTIN 4046356827423 Weight per Piece (excluding packing) 50.000 g Custom tariff number 85366990 Country of origin Germany Technical data General Note Order information: Order crimp contacts Ø 2 mm separately Type of locking for standard and SPEEDCON interlock Direction of rotation of contact chamber numbering Standard Coding N Contact connection method Crimp connection 12/22/2019   Page 1 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Technical data General Type of contacts Pin Number of positions 4 Contact diameter of power contacts 2 mm Rated current of each power contact at 25°C 25 A Contact diameter of signal contacts 2 mm Pg housing screw connection none Mounting type 4x Ø 3.2 Ambient conditions Ambient temperature -40 °C ... 125 °C Degree of protection IP67 Specifications according to DIN EN 61984:2001 Installation height max. 3000 mm Nominal / operating voltage of power contacts 630 V Rated surge voltage of power contacts 6 kV Overvoltage category of power contacts III Degree of pollution of power contacts 3 Standards and Regulations Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded 12/22/2019   Page 2 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Technical data Standards and Regulations • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings 12/22/2019   Page 3 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Schematic diagram Installation dimensions 12/22/2019   Page 4 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Schematic diagram Connector pin assignment 12/22/2019   Page 5 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Dimensional drawing Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27143400 eCl@ss 6.0 27279200 eCl@ss 7.0 27440103 eCl@ss 8.0 27440103 eCl@ss 9.0 27440102 ETIM ETIM 3.0 EC001121 ETIM 4.0 EC002635 ETIM 5.0 EC002061 ETIM 6.0 EC002061 UNSPSC UNSPSC 6.01 43172015 UNSPSC 7.0901 43201404 UNSPSC 11 43172015 UNSPSC 12.01 43201404 12/22/2019   Page 6 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Classifications UNSPSC UNSPSC 13.2 39121413 UNSPSC 18.0 39121413 UNSPSC 19.0 39121413 UNSPSC 20.0 39121413 UNSPSC 21.0 39121413 Approvals Approvals Approvals UL Recognized / cUL Recognized / EAC / cULus Recognized Ex Approvals Approval details UL Recognized    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm     Nominal voltage UN 600 V Nominal current IN 15 A mm²/AWG/kcmil 14 cUL Recognized    http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm     Nominal voltage UN 600 V Nominal current IN 15 A mm²/AWG/kcmil 14 EAC      FILE E 335019  FILE E 335019  B.01742 12/22/2019   Page 7 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Approvals cULus Recognized       Accessories Accessories Crimp contact Crimp contact - ST-20KP010 - 1607655 Crimp contact, turned, contact diameter: 2 mm, crimp range: 0.25 mm² ... 1 mm²     Crimp contact - ST-20KP020 - 1607656 Crimp contact, turned, Single contact, contact diameter: 2 mm, crimp range: 1 mm² ... 2.5 mm²     Mounting material Color-coding - ST-Z0019 - 1620621 Color-coding, color: green     Color-coding - ST-Z0020 - 1620622 Color-coding, color: orange     12/22/2019   Page 8 / 10 https://www.phoenixcontact.com/us/products/1619209 Device connector, front mounting - ST-3EP1N8AW500S - 1619209 Accessories Color-coding - ST-Z0021 - 1620623 Color-coding, color: black     Contact removal tool - ST-Z0001 - 1607770 Unlocking tool for contact carriers for snapping in the M17 device connectors     Protective cover Protective cap - ST-Z0006 - 1607776 Plastic protection cap for connectors with M17 external thread     Metal protective cap - ST-Z0014 - 1616069 Metal protection cap for connectors with M17 external thread     Metal protective cap - ST-Z0013 - 1616068 Metal protection cap with steel wire for connectors with M17 external thread     12/22/2019   Page 9 / 10 https://www.phoenixcontact.com/us/products/1619209 Phoenix Contact 2019 © - all rights reserved http://www.phoenixcontact.com 12/22/2019   Page 10 / 10