1628484

M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user documentation. Our general terms of use for downloads are valid. M23, Device connector front mounting, series: M23 PRO, angled rotatable, for standard and ONECLICK fast locking system, No. of pos.: 4+3+PE, contact connection type: Pin, Crimp connection, flange dimensions: 28 mm x 28 mm, Item is lead-free in accordance with RoHS II without Exemption 6c (Pb  50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the Jan 8, 2024, 10:06 AM Page 2 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Product properties Product type Circular connectors (device side) Material specifications Flammability rating according to UL 94 V0 Connector Insulating body Note Order information: Order crimp contacts 4 x Ø 1 mm, 4 x Ø 2 mm separately Insulation body material PA 6.6 Insertion/withdrawal cycles 100 Connection method Crimp connection Contact switching type Pin Application Power Number of positions 8 Connection profile 4+3+PE Contact diameter Power contacts 2 mm Litz wire cross-section Power contacts min. 0.25 mm² Litz wire cross-section Power contacts max. 4 mm² Rated current Power contacts 30 A Note for max. connection cross section Rated voltage 630 V Rated surge voltage 6 kV Overvoltage category III Degree of pollution 3 Contact diameter Signal contacts 1 mm Litz wire cross-section Signal contacts min. 0.06 mm² Litz wire cross-section Signal contacts max. 1 mm² Nominal current per signal contact 9A Note for max. connection cross section Rated voltage Signal contact 250 V Rated surge voltage 4 kV Overvoltage category III Degree of pollution 3 Installation height 3000 m Housing Housing material GD-Zn Jan 8, 2024, 10:06 AM Page 3 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Flange dimensions 28 mm x 28 mm Type of locking for standard and ONECLICK fast locking system Degree of protection (plugged in) IP66 / IP68 (2m / 24h) / IP69K Thread type M23 Environmental and real-life conditions Ambient conditions Degree of protection IP68 Ambient temperature (operation) -40 °C ... 105 °C (see to derating) Permanent temperature 125 °C (DIN EN 60512-9-2 / 1000 h) Jan 8, 2024, 10:06 AM Page 4 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Drawings I [A] Diagram 45 40 35 30 25 20 15 10 5 0 1 1 0 2 = 3x4mm 10 20 30 40 50 60 70 80 90 100 110 120 130  [°C] I = current strength, ϑ = ambient temperature, 3 x 30 A + 2 x 1 A constant Dimensional drawing 138 ° 192 ° 4x Ø3 ,1 47,3 62,3 M23x1 26,9 41,4 22,6 28 Technical drawings can be found under Downloads Jan 8, 2024, 10:06 AM Page 5 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Schematic diagram C B D3 4 A1 Connector pin assignment Jan 8, 2024, 10:06 AM Page 6 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Dimensional drawing A-A -0,2 A +0,1 Ø20,1 4xM3 area for Rz16 29 ±0,5 Ø 0,1 A Rz16 A A 22,64 Installation dimensions Jan 8, 2024, 10:06 AM Page 7 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Approvals To download certificates, visit the product detail page: https://www.phoenixcontact.com/us/products/1628484  UL Listed  cUL Listed Approval ID: E468743-20190627 Approval ID: E468743-20190627 cULus Listed Jan 8, 2024, 10:06 AM Page 8 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Classifications ECLASS ECLASS-11.0 27440109 ECLASS-12.0 27440109 ECLASS-13.0 27440109 ETIM ETIM 9.0 EC003569 UNSPSC UNSPSC 21.0 39121400 Jan 8, 2024, 10:06 AM Page 9 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Environmental product compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Jan 8, 2024, 10:06 AM Page 10 (14) M23-7EP198AA600S - Device connector front mounting 1628484 https://www.phoenixcontact.com/us/products/1628484 Accessories M23-Z0001 - Screw 1035117 https://www.phoenixcontact.com/us/products/1035117 Anchor screw, self-tapping, for M23PRO series angled device connectors SF-20KP011 - Crimp contact 1050147 https://www.phoenixcontact.com/us/products/1050147 Crimp contact, Pin, turned, contact diameter: 2 mm, crimp range: 0.25 mm2 ... 1 mm2, Alternative product in accordance with RoHS II without Exemption 6c (Pb