1628493

https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Device connector, front mounting, M23 PRO, angled rotatable, for standard and ONECLICK fast locking system, M23, No. of pos.: 17, type of contact: Socket, Crimp connection, flange dimensions: 28 mm x 28 mm, coding:N Your advantages  Solutions with cross-manufacturer compatibility for standard and fast locking systems  Modern, consistent design for highly convenient operation Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626621883 Weight per Piece (excluding packing) 120.000 g Custom tariff number 85366990 Country of origin Germany Technical data Temperature range Temperature range -40 °C ... 125 °C Standards and Regulations Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. 03/29/2021   Page 1 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Technical data Standards and Regulations • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Data of the insulating body Note Order information: Order crimp contacts Ø 1 mm separately Coding N Insulator material PA 6.6 Contact connection method Crimp connection Type of contacts Socket Application Signal Number of positions 17 Direction of rotation Standard 03/29/2021   Page 2 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Technical data Data of the insulating body Contact diameter of signal contacts 1 mm Litz wire cross section of signal contacts min. 0.08 mm² Litz wire cross section of signal contacts max. 1 mm² Nominal current per signal contact 8A Note for max. connection cross section Rated voltage of signal contact 125 V Rated surge voltage 2 kV Overvoltage category III Degree of pollution 3 Note for max. connection cross section Installation height 2000 m Housing data Housing material GD-Zn Flange dimensions 28 mm x 28 mm Type of locking for standard and ONECLICK fast locking system Degree of protection (when plugged in) IP66 / IP68 (2 m / 24 h) Thread type M23 Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings Schematic diagram Dimensional drawing A-A -0,2 Rz16 N 1 11 A 12 16 10 3 9 14 17 15 4 8 SO 7 5 6 Ø20,1 13 29 ±0,5 Ø 0,1 A area for Rz16 2 +0,1 4xM3 A A 22,64 Installation dimensions 03/29/2021   Page 3 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Dimensional drawing 138 ° 192 ° 4x Ø 3,1 55 40 M23x1 Diagram 26,9 41,4 22,6 28 Technical drawings can be found under Downloads I = current strength, ϑ = ambient temperature, 17x 6 A Classifications eCl@ss eCl@ss 10.0.1 27440109 eCl@ss 11.0 27440109 eCl@ss 9.0 27440103 ETIM ETIM 6.0 EC002061 Accessories Accessories Crimp contact Crimp contact - RC-11S2000 - 1596772 Crimp contact, turned, Single contact, contact diameter: 1 mm, crimp range: 0.08 mm² ... 0.22 mm²     Crimp contact - RC-12S2000 - 1599600 Crimp contact, turned, Single contact, contact diameter: 1 mm, crimp range: 0.14 mm² ... 0.56 mm²     03/29/2021   Page 4 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Accessories Crimp contact - RC-1KS2000 - 1602998 Crimp contact, turned, Single contact, contact diameter: 1 mm, crimp range: 0.5 mm² ... 1 mm²     Crimp contact - RC-22S2000 - 1603327 Crimp contact, rolled, Single contact, contact diameter: 1 mm, crimp range: 0.22 mm² ... 0.56 mm², Single contact     Crimp contact - RC-21S2000 - 1603315 Crimp contact, rolled, Single contact, contact diameter: 1 mm, crimp range: 0.08 mm² ... 0.22 mm², Single contact     Crimp contact - RC-22S2300 - 1603330 Crimp contact, rolled, Taped articles, number of pieces per reel: 500, contact diameter: 1 mm, crimp range: 0.22 mm² ... 0.56 mm²     Crimp contact - RC-22S2400 - 1603332 Crimp contact, rolled, number of pieces per reel: 10000, contact diameter: 1 mm, crimp range: 0.22 mm² ... 0.56 mm²     03/29/2021   Page 5 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Accessories Crimp contact - RC-21S2300 - 1603318 Crimp contact, rolled, Taped articles, number of pieces per reel: 500, contact diameter: 1 mm, crimp range: 0.08 mm² ... 0.22 mm²     Crimp contact - RC-21S2400 - 1616500 Crimp contact, rolled, number of pieces per reel: 10000, contact diameter: 1 mm, crimp range: 0.08 mm² ... 0.22 mm²     Mounting material Screw - M23-Z0001 - 1035117 Anchor screw, self-tapping, for M23-PRO series angled device connectors     Protective cover Protective cap - RC-Z2059 - 1604225 Plastic protection cap for connectors with M23 external thread     Metal protective cap - RC-Z2104 - 1604260 Metal protection cap for signal connectors with M23 external thread     03/29/2021   Page 6 / 7 https://www.phoenixcontact.com/us/products/1628493 Device connector, front mounting - M23-17S1N8AA600S - 1628493 Accessories Universal tools Contact removal tool - UNIFOX-RT M23 17 - 1253082 Removal tool for the M23 PRO series 17-position signal contact carrier     Phoenix Contact 2021 © - all rights reserved http://www.phoenixcontact.com 03/29/2021   Page 7 / 7