1636907

https://www.phoenixcontact.com/us/products/1636907 Contact insert module - HC-M-HS 200/70-MOD-ST-PE - 1636907 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) HEAVYCON contact insert module, connector, 1-pos., for axial screw connection, 200 A, 40-70 mm², for the PE connection Key Commercial Data Packing unit 1 pc Weight per Piece (excluding packing) 97.6 g Custom tariff number 85366990 Country of origin Germany Technical data Electrical characteristics Note For HEAVYCON HC-B6 to B48 housing (housing height: min. 72 mm), HCM-MHR... hinged retaining frame required, axial connection for 5 mm Allen key Rated current 200 A Number of positions 1 Ambient conditions Ambient temperature (operation) -40 °C ... 125 °C Mechanical characteristics Conductor cross section 40 mm² ... 70 mm² (The cross section specification refers to the geometric cross section of the cable used) Connection cross section AWG 1 ... 00 Stripping length of the individual wire 16 mm Tightening torque 9 Nm (40 - 50 mm²) 10 Nm (70 mm²) Wire diameter including insulation 12 mm (40 mm²) 16 mm (70 mm²) 04/06/2016   Page 1 / 4 https://www.phoenixcontact.com/us/products/1636907 Contact insert module - HC-M-HS 200/70-MOD-ST-PE - 1636907 Technical data Mechanical characteristics Hexagonal socket WAF 5 Insertion/withdrawal cycles ≥ 500 Minimum housing height 72 mm General Series HC-M-HS Number of module slots 2 Connection method Axial screw connection Flammability rating according to UL 94 V0 Assembly instructions - Use only flexible conductors, - Connection of wires with 5 mm an Allen wrench, - Housing height h ≥ 72 mm, - Connectors may only be operated without load/voltage. Connection Note on axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Use of cables with a geometric cross section that differs greatly from the nominal cross section of the cable should be checked before use. The wiring space for axial screw technology is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) should be checked before use. Assembly instructions Before assembly, ensure that the tapered screw is turned back all the way (chamber is open). The cables must not be twisted. The wires should be inserted as far as they will go into the contact chamber (until the insulation touches the contact). Hold the wires in position and use the socket wrench to tighten. The used wire end should be cut off before connecting again. The connection screw may only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable should be mechanically intercepted at an appropriate distance from the connection point (e.g., by using a plate cutout). DIN VDE 0100-520:2003-06 contains information on how to do this correctly. The module cannot be used simultaneously with HC-B..-TMB-SD-IP65 and HCB..-TMS-SD-IP65 protective covers. PE mounting plate The PE plate must be pressed hard against the swing frame using the 4 screws. First loosen the 4 screws of the PE plate and then tighten them again once the module is fixed in the swing frame. Material data Contact material Copper alloy Contact surface material Ag Contact carrier material PC Standards and Regulations Connection in acc. with standard UL Flammability rating according to UL 94 V0 04/06/2016   Page 2 / 4 https://www.phoenixcontact.com/us/products/1636907 Contact insert module - HC-M-HS 200/70-MOD-ST-PE - 1636907 Classifications eCl@ss eCl@ss 4.0 272607xx eCl@ss 4.1 27260701 eCl@ss 5.0 27143424 eCl@ss 5.1 27143424 eCl@ss 6.0 27143424 eCl@ss 7.0 27440209 eCl@ss 8.0 27440207 ETIM ETIM 3.0 EC000438 ETIM 4.0 EC000438 ETIM 5.0 EC000438 UNSPSC UNSPSC 6.01 30211923 UNSPSC 7.0901 39121522 UNSPSC 11 39121522 UNSPSC 12.01 39121522 UNSPSC 13.2 39121522 Approvals Approvals Approvals UL Recognized / EAC Ex Approvals Approvals submitted Approval details 04/06/2016   Page 3 / 4 https://www.phoenixcontact.com/us/products/1636907 Contact insert module - HC-M-HS 200/70-MOD-ST-PE - 1636907 Approvals UL Recognized      mm²/AWG/kcmil 2 Nominal current IN 200 A Nominal voltage UN 600 V EAC  Drawings Diagram Dimensional drawing 34,4 29,4 350 300 23 2 250 200 54,5 Operating current [A] 400 150 1 100 1 = 50 mm2 50 2 = 70 mm 0 0 20 2 40 60 80 100 120 Ambient temperature [°C] Male insert Schematic diagram Axial screw connection Phoenix Contact 2016 © - all rights reserved http://www.phoenixcontact.com 04/06/2016   Page 4 / 4