1637168

https://www.phoenixcontact.com/us/products/1637168 Contact insert module - HC-M-HS 200/40-MOD-ST - 1637168 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) HEAVYCON contact insert module, connector, 1-pos., for axial screw connection, 200 A, 25-40 mm² Key Commercial Data Packing unit 1 pc Weight per Piece (excluding packing) 71.7 g Custom tariff number 85366990 Country of origin Germany Technical data Electrical characteristics Note Required for housing HC-B6 to B48, (housing height min. 72 mm), housing HC-ADVANCE-B6 to B24, hinged retaining frame HC-M-MHR..., axial connection for 5 mm Allen wrench Rated voltage (III/3) 1000 V Rated current 200 A Rated surge voltage 8 kV Number of positions 1 Ambient conditions Ambient temperature (operation) -40 °C ... 125 °C Mechanical characteristics Conductor cross section 25 mm² ... 40 mm² (The cross section specification refers to the geometric cross section of the cable used) Connection cross section AWG 3 ... 2 Stripping length of the individual wire 16 mm Tightening torque 8 Nm (25-35 mm²) 9 Nm (40 mm²) 04/06/2016   Page 1 / 5 https://www.phoenixcontact.com/us/products/1637168 Contact insert module - HC-M-HS 200/40-MOD-ST - 1637168 Technical data Mechanical characteristics Wire diameter including insulation 12 mm (25 mm²) 16 mm (40 mm²) Hexagonal socket WAF 5 Insertion/withdrawal cycles ≥ 500 Minimum housing height 72 mm General Series HC-M-HS Number of module slots 2 Connection method Axial screw connection Flammability rating according to UL 94 V0 Degree of pollution 3 Overvoltage category III Assembly instructions - Use only flexible conductors, - Connection of wires with 5 mm an Allen wrench, - Housing height h ≥ 72 mm, - Connectors may only be operated without load/voltage. Connection Note regarding axial connection technology: Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used. Use of cables with a geometric cross section very different from the cable's nominal cross section should be checked before use. The wiring space of the axial screw method is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) should be checked before use. Connection Before starting to connect, ensure that the tapered screw is turned back all the way (chamber is open). The cables must not be twisted. The wires should be inserted as far as they will go in the contact chamber (until the insulation touches the contact). Hold wires in position and use socket wrench to tighten. The used wire end should be cut off before connecting again. The connection screw may only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable should be mechanically intercepted at an appropriate distance from the connection point (e.g., by using a plate cutout). DIN VDE 0100-520:2003-06 contains information on how to do this correctly. The module cannot be used simultaneously with the HC-B..-TMB-SD-IP65 and HC-B..-TMS-SD-IP65 protective covers. Material data Contact material Copper alloy Contact surface material Ag Contact carrier material PC Standards and Regulations Connection in acc. with standard UL 04/06/2016   Page 2 / 5 https://www.phoenixcontact.com/us/products/1637168 Contact insert module - HC-M-HS 200/40-MOD-ST - 1637168 Technical data Standards and Regulations Flammability rating according to UL 94 V0 Classifications eCl@ss eCl@ss 4.0 272607xx eCl@ss 4.1 27260701 eCl@ss 5.0 27143424 eCl@ss 5.1 27143424 eCl@ss 6.0 27143424 eCl@ss 7.0 27440209 eCl@ss 8.0 27440207 ETIM ETIM 3.0 EC000438 ETIM 4.0 EC000438 ETIM 5.0 EC000438 UNSPSC UNSPSC 6.01 30211923 UNSPSC 7.0901 39121522 UNSPSC 11 39121522 UNSPSC 12.01 39121522 UNSPSC 13.2 39121522 Approvals Approvals Approvals UL Recognized / EAC / EAC Ex Approvals Approvals submitted 04/06/2016   Page 3 / 5 https://www.phoenixcontact.com/us/products/1637168 Contact insert module - HC-M-HS 200/40-MOD-ST - 1637168 Approvals Approval details UL Recognized      mm²/AWG/kcmil 2 Nominal current IN 200 A Nominal voltage UN 600 V EAC  EAC  Drawings Diagram Diagram 400 Operating current [A] Operating current [A] 400 350 300 2 250 200 150 1 100 1 = 50 mm2 50 0 20 2 300 250 200 150 1 100 1 = 50 mm2 50 2 = 70 mm2 0 350 40 60 80 100 120 0 2 = 70 mm2 0 20 40 Ambient temperature [°C] Derating diagram (3 modules in HC-B 24 housing) 80 100 120 Ambient temperature [°C] Two modules in B24 housing Dimensional drawing Schematic diagram 29,4 54,5 23 34,2 60 Axial screw connection Male insert 04/06/2016   Page 4 / 5 https://www.phoenixcontact.com/us/products/1637168 Phoenix Contact 2016 © - all rights reserved http://www.phoenixcontact.com 04/06/2016   Page 5 / 5