1655098

https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) D-SUB contact insert, shell size 1, with 15 signal contacts, type of contact pin, for PCB assembly, angled, fixing with 4-40 UNC thread and solder pins, for panel mounting frame VS-09-... Key Commercial Data Packing unit 1 pc Minimum order quantity 10 pc GTIN GTIN 4046356029032 Weight per Piece (excluding packing) 11.940 g Custom tariff number 85366990 Country of origin Germany Technical data Mechanical characteristics Connection method Solder connection Overvoltage category III Degree of pollution 2 Weight 11.1 g Flammability rating according to UL 94 V0 Ambient conditions Ambient temperature (operation) -55 °C ... 105 °C Material data Contact surface material Au/Sn 06/28/2020   Page 1 / 6 https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Technical data Material data Contact material Copper alloy Contact carrier material Glass-fiber reinforced thermoplastics, UL 94 V0 Width 21.4 mm Height 17.1 mm Length 31.19 mm Mounting type Threads and solder pins Electrical characteristics Number of positions 15 Rated current 3 A (at 20 °C) Overvoltage category III Degree of pollution 2 Rated voltage (III/3) 60 V Test voltage 1000 V Standards and Regulations Flammability rating according to UL 94 V0 Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. 06/28/2020   Page 2 / 6 https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Technical data Standards and Regulations • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Operate the connector only when it is fully plugged in and interlocked. • Operate the connector only when it is fully plugged in. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings 06/28/2020   Page 3 / 6 https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Dimensional drawing D-SUB contact insert Classifications eCl@ss eCl@ss 10.0.1 27440205 eCl@ss 4.0 27260700 eCl@ss 4.1 27260700 eCl@ss 5.0 27260700 eCl@ss 5.1 27260700 06/28/2020   Page 4 / 6 https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Classifications eCl@ss eCl@ss 6.0 27260700 eCl@ss 7.0 27440302 eCl@ss 8.0 27440302 eCl@ss 9.0 27440205 ETIM ETIM 2.0 EC000438 ETIM 3.0 EC000438 ETIM 4.0 EC000438 ETIM 5.0 EC001132 ETIM 6.0 EC000438 ETIM 7.0 EC000438 UNSPSC UNSPSC 6.01 30211923 UNSPSC 7.0901 39121522 UNSPSC 11 39121522 UNSPSC 12.01 39121522 UNSPSC 13.2 39121522 UNSPSC 18.0 39121522 UNSPSC 19.0 39121522 UNSPSC 20.0 39121522 UNSPSC 21.0 39121522 Approvals Approvals Approvals EAC Ex Approvals Approval details 06/28/2020   Page 5 / 6 https://www.phoenixcontact.com/us/products/1655098 D-SUB contact insert - VS-09-ST-DSUB-HD-ER - 1655098 Approvals EAC      B.01687 Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com 06/28/2020   Page 6 / 6