1885240

https://www.phoenixcontact.com/us/products/1885240 Contact insert - VC-AFOS 2 - 1885240 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Contact insert module, for panel mounting frames for accommodating 2 optical fibers VC-FSMA-M ... Quick mounting connectors Your advantages  Compact design  Proven COMBICON technology  Universal connection  Can be keyed to prevent incorrect connection Key Commercial Data Packing unit 1 pc Minimum order quantity 10 pc GTIN GTIN 4017918176273 Weight per Piece (excluding packing) 3.430 g Custom tariff number 85369010 Country of origin Poland Technical data General Note When using fiber optics, the minimum permissible bending radii must be observed. Number of positions F-SMA type 905, IEC 874-2 Insertion/withdrawal cycles > 100 Size VC1/-2/-3/-4 11/28/2019   Page 1 / 5 https://www.phoenixcontact.com/us/products/1885240 Contact insert - VC-AFOS 2 - 1885240 Technical data General Stripping length of the individual wire 12 mm (minimum) Ambient conditions Ambient temperature (operation) -20 °C ... 70 °C Material data Housing material PA 6.6 Standards and Regulations Flammability rating according to UL 94 V0 CE safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. 11/28/2019   Page 2 / 5 https://www.phoenixcontact.com/us/products/1885240 Contact insert - VC-AFOS 2 - 1885240 Technical data Standards and Regulations • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products • Operate the connector only when it is fully plugged in. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings Dimensional drawing Classifications eCl@ss eCl@ss 10.0.1 27440217 eCl@ss 4.0 27140800 eCl@ss 4.1 27140800 eCl@ss 5.0 27143400 eCl@ss 5.1 27261200 eCl@ss 6.0 27261200 eCl@ss 7.0 27440205 11/28/2019   Page 3 / 5 https://www.phoenixcontact.com/us/products/1885240 Contact insert - VC-AFOS 2 - 1885240 Classifications eCl@ss eCl@ss 8.0 27440205 eCl@ss 9.0 27440217 ETIM ETIM 2.0 EC000438 ETIM 3.0 EC000438 ETIM 4.0 EC000438 ETIM 5.0 EC000438 ETIM 6.0 EC000438 ETIM 7.0 EC000438 UNSPSC UNSPSC 6.01 30211923 UNSPSC 7.0901 39121522 UNSPSC 11 39121522 UNSPSC 12.01 39121522 UNSPSC 13.2 39121421 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC      B.01742 Accessories Accessories Assembly tool 11/28/2019   Page 4 / 5 https://www.phoenixcontact.com/us/products/1885240 Contact insert - VC-AFOS 2 - 1885240 Accessories Polisher - VC-POLISHER/M FSMA - 1884982 Polisher, metal, for repeated preparation of VARIOCON fiber optic ferrules     Assembly tool - PSM-SET-FSMA-POLISH - 2799348 Polymer fiber polishing set, for F-SMA quick mounting connectors     Phoenix Contact 2019 © - all rights reserved http://www.phoenixcontact.com 11/28/2019   Page 5 / 5