2320018

https://www.phoenixcontact.com/gb/products/2320018 DC/DC converters - MINI-PS- 12- 24DC/ 5-15DC/2 - 2320018 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Primary-switched MINI DC/DC converter for DIN rail mounting, input: 1-phase, output: 5 - 15 V DC/2 A Product Description MINI DC/DC converter for MCR technology. DC/DC converters alter the voltage level, regenerate the voltage at the end of long cables or enable the creation of independent supply systems by means of electrical isolation. Why buy this product  Electrical isolation: for setting up independent supply systems  Support conversion to various voltage levels  Constant voltage: output voltage regenerated even at the end of long cables Key Commercial Data Packing unit 1 STK GTIN GTIN 4046356478519 Weight per Piece (excluding packing) 200.000 g Custom tariff number 85044030 Country of origin China Technical data Dimensions Width 22.5 mm Height 99 mm Depth 107 mm Ambient conditions Degree of protection IP20 Ambient temperature (operation) -25 °C ... 70 °C (> +60°C derating) 08/16/2017   Page 1 / 5 https://www.phoenixcontact.com/gb/products/2320018 DC/DC converters - MINI-PS- 12- 24DC/ 5-15DC/2 - 2320018 Technical data Ambient conditions Ambient temperature (storage/transport) -40 °C ... 85 °C Max. permissible relative humidity (operation) ≤ 95 % (At +25°C, non-condensing) Climatic class 3K3 (in acc. with EN 60721) Degree of pollution 2 Input data Nominal input voltage range 12 V DC ... 24 V DC Input voltage range 10 V DC ... 32 V DC (> 10.5 V DC start) Frequency range DC 0 Hz Current consumption 2.3 A (12 V DC) 1.1 A (24 V DC) Inrush surge current < 10 A (typical) Power failure bypass > 4 ms (12 V DC) > 18 ms (24 V DC) Input fuse 6.3 A (slow-blow, internal) Output data Nominal output voltage 12 V DC ±1 % Setting range of the output voltage (USet) 5 V DC ... 15 V DC Nominal output current (IN) 2 A (-25 °C ... 60 °C) Derating 60 °C ... 70 °C (2.5%/K) Connection in parallel Yes, for assembling redundant systems and increasing efficiency Connection in series yes Feedback resistance 30 V DC Circuit breaker against surge voltage at output by invasive foreign matter < 25 V DC Residual ripple < 20 mVPP (20 MHz) Typical response time < 0.5 s Peak switching voltages nominal load < 10 mVPP (20 MHz) Maximum power dissipation in no-load condition 88 % (at 24 V DC and nominal values) Insulation voltage input/output 1.5 kV (type test) 1 kV (routine test) Protection class III Degree of protection IP20 > 2072000 h (40 °C) Mounting position horizontal DIN rail NS 35, EN 60715 Assembly instructions Can be aligned: Horizontally 0 mm, vertically 50 mm Connection data, input 08/16/2017   Page 2 / 5 https://www.phoenixcontact.com/gb/products/2320018 DC/DC converters - MINI-PS- 12- 24DC/ 5-15DC/2 - 2320018 Technical data Connection data, input Connection method Pluggable screw connection Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 2.5 mm² Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 2.5 mm² Conductor cross section AWG min. 24 Conductor cross section AWG max. 14 Stripping length 7 mm Screw thread M3 Connection data, output Connection method Pluggable screw connection Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 2.5 mm² Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 2.5 mm² Conductor cross section AWG min. 24 Conductor cross section AWG max. 14 Stripping length 7 mm Screw thread M3 Signaling Output name DC OK active Output description UOUT > 0.9 x UN: High signal Output voltage Uout Continuous load current ≤ 20 mA Status display "DC OK" LED green Note on status display UOUT > 0.9 x UN: LED ON Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 2.5 mm² Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 2.5 mm² Conductor cross section AWG min. 24 Conductor cross section AWG max. 14 Tightening torque, min 0.5 Nm Tightening torque max 0.6 Nm Screw thread M3 Standards and Regulations Electromagnetic compatibility Conformance with EMC Directive 2014/30/EU Noise emission EN 55011 (EN 55022) Noise immunity EN 61000-6-2:2005 08/16/2017   Page 3 / 5 https://www.phoenixcontact.com/gb/products/2320018 DC/DC converters - MINI-PS- 12- 24DC/ 5-15DC/2 - 2320018 Technical data Standards and Regulations Connection in acc. with standard CUL Standards/regulations EN 61000-4-2 Contact discharge 8 kV (Contact discharge) Standards/regulations EN 61000-4-3 Frequency range 80 MHz ... 3 GHz Test field strength 10 V/m Standards/regulations EN 61000-4-4 Comments Criterion B Standards/regulations EN 61000-4-5 EN 61000-6-3 EN 61000-4-6 Frequency range 0.15 MHz ... 80 MHz (10 V) Standards/regulations EN 61000-4-11 Low Voltage Directive Conformance with LV directive 2006/95/EC Standard - Electrical safety EN 60950-1/VDE 0805 (SELV) Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations EN 50178/VDE 0160 (PELV) Standard - Safe isolation DIN VDE 0100-410 DIN VDE 0106-101 UL approvals UL/C-UL listed UL 508 UL/C-UL Recognized UL 60950-1 UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D (Hazardous Location) Shock 18 ms, 30g, in each space direction (according to IEC 60068-2-27) Vibration (operation) < 15 Hz, amplitude ±2.5 mm (according to IEC 60068-2-6) 15 Hz ...150 Hz, 2.3g Rail applications EN 50121-4 Drawings Block diagram Dimensional drawing 107 NC NC 99 DC OK 08/16/2017   Page 4 / 5 https://www.phoenixcontact.com/gb/products/2320018 Phoenix Contact 2017 © - all rights reserved http://www.phoenixcontact.com 08/16/2017   Page 5 / 5