2701214

IB IL 24/48 DOR 2/W-XC-PAC Inline digital output terminal, version for extreme conditions, 2 relay PDTs Data sheet 8463_en_01 1 © PHOENIX CONTACT 2015-08-12 Description The terminal is designed for use within an Inline station. It has two floating relay PDTs which are independent of each other. Thanks to special engineering measures and tests, the terminal can be used under extreme ambient conditions. Features – – – – – – – – – Two relay outputs Floating connections for 2 actuators Nominal current of each output: 2 A Total current of the terminal: 4 A Segment voltage US connected Diagnostic and status indicators Can be used under extreme ambient conditions Extended temperature range of -40°C ... +70°C (see “Tested successfully: use under extreme ambient conditions”) Painted PCBs WARNING: Undefined system state By default, the position of the relay contacts on the module is not defined. To prevent undesired system states, perform a complete cycle (on/off) before connecting the segment voltage. This data sheet is only valid in association with the IL SYS INST UM E user manual. Make sure you always use the latest documentation. It can be downloaded from the product at phoenixcontact.net/products. IB IL 24/48 DOR 2/W-XC-PAC 2 Table of contents 1 Description .............................................................................................................................. 1 2 Table of contents ..................................................................................................................... 2 3 Ordering data .......................................................................................................................... 3 4 Technical data ......................................................................................................................... 3 5 Additional tables ...................................................................................................................... 6 5.1 Maximum switching current for ohmic load depending on the switching voltage................................... 6 5.2 Power dissipation ................................................................................................................ 6 5.3 Limitation of simultaneity, derating ........................................................................................... 7 5.4 Air clearances and creepage distances ..................................................................................... 7 6 Tested successfully: Use under extreme ambient conditions .................................................. 8 7 Internal circuit diagram ............................................................................................................ 9 8 Special features of the terminal ............................................................................................... 9 8.1 Switching a voltage equal to the segment voltage ........................................................................ 9 8.2 Switching a voltage unequal to the segment voltage ..................................................................... 9 9 Local status and diagnostic indicators ................................................................................... 10 10 Terminal point assignment..................................................................................................... 10 11 Connection notes and examples ........................................................................................... 11 12 Process data.......................................................................................................................... 11 8463_en_01 PHOENIX CONTACT 2 IB IL 24/48 DOR 2/W-XC-PAC 3 Ordering data Description Type Order No. Pcs./Pkt. Inline digital output terminal, version for extreme conditions, complete with accessories (connector plug and labeling field), 2 relay PDTs, gold contact, 5 - 48 V DC, 2 A IB IL 24/48 DOR 2/W-XC-PAC 2701214 1 Accessories Type Order No. Pcs./Pkt. Labeling field, width: 12.2 mm (Marking) IB IL FIELD 2 2727501 10 Insert strip, Sheet, white, unlabeled, can be labeled with: Office printing systems, Plotter: Laser printer, Mounting type: Insert, Lettering field: 62 x 10 mm (Marking) ESL 62X10 0809492 1 Connector, for digital 1, 2 or 8-channel Inline terminals (Connector/ Adapter) IB IL SCN-8 2726337 10 Zack Marker strip, flat, Strip, white, unlabeled, can be labeled with: Plotter, Mounting type: Snap into flat marker groove, for terminal block width: 6.2 mm, Lettering field: 5.15 x 6.15 mm (Marking) ZBF 6:UNBEDRUCKT 0808710 10 Zack Marker strip, flat, white, for terminal block width: 6.2 mm (Marking) ZBF 6:SO/CMS 0808778 1 Flat zack marker sheet, white, for terminal block width: 6.2 mm (Marking) ZBFM 6:SO/CMS 0803650 1 Flat zack marker sheet, Sheet, white, unlabeled, can be labeled with: Plot- ZBFM 6/WH:UNBEDRUCKT ter, Mounting type: Snap into flat marker groove, for terminal block width: 6.2 mm, Lettering field: 5 x 5.5 mm (Marking) 0803618 10 Inline distance terminal, complete with accessories IB IL DOR LV-SET-PAC 2861645 1 Documentation Type Order No. Pcs./Pkt. Application note, English, The safety-related segment circuit AH EN IL SAFE - - Data sheet, English, INTERBUS addressing DB GB IBS SYS ADDRESS - - Application note, English, Using distance terminal blocks and interference suppression measures on inductive loads AH EN IB IL DOR - - 4 Technical data Dimensions (nominal sizes in mm) 140,5 71,5 119,8 Width 12.2 mm Height 119.8 mm Depth 71.5 mm Note on dimensions Housing dimensions 8463_en_01 PHOENIX CONTACT 3 IB IL 24/48 DOR 2/W-XC-PAC General data Color green Weight 63 g (with connector) Operating mode Process data mode with 2 bits Ambient temperature (operation) -25 °C ... 55 °C (Standard) -40 °C ... 70 °C (Extended, see section “Tested successfully: use under extreme ambient conditions” in the data sheet.) Ambient temperature (storage/transport) -40 °C ... 85 °C Permissible humidity (operation) 10 % ... 95 % (according to DIN EN 61131-2) Permissible humidity (storage/transport) 10 % ... 95 % (according to DIN EN 61131-2) Air pressure (operation) 70 kPa ... 106 kPa (up to 3000 m above sea level) Air pressure (storage/transport) 70 kPa ... 106 kPa (up to 3000 m above sea level) Degree of protection IP20 Protection class III, IEC 61140, EN 61140, VDE 0140-1 Connection data Designation Inline connector Connection method Spring-cage connection Conductor cross section solid / stranded 0.08 mm² ... 1.5 mm² / 0.08 mm² ... 1.5 mm² Conductor cross section [AWG] 28 ... 16 Stripping length 8 mm Interface Inline local bus Connection method Inline data jumper Transmission speed 500 kBit/s Power consumption Communications power UL 7.5 V DC Current consumption from UL max. 30 mA Power consumption 0.23 W (at UL) Relay output Number of outputs 2 Connection method Spring-cage connection Connection method Floating SPDT relay contact Nominal output voltage 48 V DC Output voltage range 5 V AC ... 30 V AC 5 V DC ... 60 V DC Maximum output current per channel 2A Contact type 2 floating PDT contacts Contact material AgSnO2, hard gold-plated Contact resistance 75 mΩ Switching voltage min. 10 mV (DC) max. 30 V AC (PELV (EN 61131)) max. 60 V DC (PELV (EN 61131)) Switching current min. 10 µA 2 A (30 V DC) 1 A (60 V DC) Limiting continuous current 2 A (at maximum ambient temperature) Switching capacity 60 W 62.5 VA (ohmic) Switching frequency 1 Hz (without load) ; 1 Hz (with load) Nominal power consumption 200 mW 8463_en_01 PHOENIX CONTACT 4 IB IL 24/48 DOR 2/W-XC-PAC Relay output Coil resistance 178 Ω ±10 % (at 20 °C) Typical response time typ. 20 ms Bouncing time 4 ms (for on and off) Typical release time typ. 20 ms Service life, electrical 108 cycles Mechanical service life 2x 105 cycles Common potentials all contacts floating Programming data (INTERBUS, local bus) ID code (hex) BD ID code (dec.) 189 Length code (hex) 2C Length code (dec.) 44 Process data channel 2 Bit Input address area 0 Bit Output address area 2 Bit Parameter channel (PCP) 0 Bit Register length (bus) 2 Bit For the programming data/configuration data of other bus systems, please refer to the corresponding electronic device data sheet (e.g., GSD, EDS). Configuration and parameter data in a PROFIBUS system Required parameter data 3 Byte Need for configuration data 4 Byte Error messages to the higher level control or computer system None Electrical isolation/isolation of the voltage areas Test section Test voltage Relay contact / Bus logics 1.5 kV, 50 Hz, 1 min Contact/contact 1 kV, 50 Hz, 1 min Contact / PE 1 kV, 50 Hz, 1 min To achieve electrical isolation between the logic level and the I/O area, supply these areas from separate power supply units. Interconnection of the power supply units in the 24 V area is not permitted (see also user manual). Approvals For the latest approvals, please visit phoenixcontact.net/products. 8463_en_01 PHOENIX CONTACT 5 IB IL 24/48 DOR 2/W-XC-PAC 5 Additional tables 5.1 Maximum switching current for ohmic load depending on the switching voltage 5.2 Power dissipation Formula for calculating the power dissipation of the electronics Switching voltage (V DC) Switching current (A) 10 2.0 20 2.0 30 2.0 60 1.0 Load current IL as a function of the switching voltage US 3,0 A 2,0 IL 1 1,0 2 n PEL = 0,23 W + m x 0,14W + ∑ (ILi2 x 0,075) i=1 Where: PEL i n m ILi Total power dissipation in the terminal Continuous index Number of set outputs (n = 1 ... 2) Number of relays with controlled coil Load current of output i Power dissipation of the housing 0,3 0,1 10 30 Figure 1 1 2 US 100 V 200 Load current IL as a function of the switching voltage US DC, ohmic load AC, ohmic load PHOU = 1.2 W -25°C ≤ TA