2717113

https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Sensor/actuator terminal block, Cross section:  0.2 mm² - 4 mm², AWG: 24 - 12, Connection type: Screw connection, Width: 6.2 mm, Color: gray, Mounting type: NS 35/7,5, NS 35/15 Product Features ■ ■ ■ ■ ■ ■ ■ ■ Same shape as DIK ... three-level initiator terminal blocks The forks of the insertion bridge can be easily loosened for bridging between non-adjacent terminal blocks Terminal blocks with red and green LEDs are available for optical signaling of the initiator and actuator wiring The upper level contains the feed-through connections for the signal cable which can be labeled Alternate wiring of an actuator followed by an initiator is easy Unlike the DIK terminal blocks, the lower level of these output terminal blocks makes direct contact with the DIN rail and as a PE connection are marked yellow-green Because the spine of the insertion bridge can be snapped into place with the terminal block housing, all the terminal points can be wired freely and the bridge can be securely positioned The middle level supplies the connected actuators with power Key Commercial Data Packing unit 1 pc GTIN Weight per Piece (excluding packing) 15.76 g Custom tariff number 85369010 Country of origin Poland Technical data General Number of levels 3 Number of connections 4 Nominal cross section 2.5 mm² 05/05/2016   Page 1 / 6 https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Technical data General Color gray Insulating material PA Flammability rating according to UL 94 V2 Rated surge voltage 4 kV Degree of pollution 3 Overvoltage category III Insulating material group I Connection in acc. with standard IEC 60947-7-1 / IEC 60947-7-2 Nominal current IN 16 A (the current is determined by the component used) Maximum load current 16 A (with a 2.5 mm² conductor cross section) Nominal voltage UN 250 V (the voltage is determined by the component used) Nominal current IN (upper level) 16 A Maximum load current (upper level) 16 A Nominal voltage UN 250 V Open side panel No Dimensions Width 6.2 mm Length 61 mm Height NS 35/7,5 54.5 mm Height NS 35/15 62 mm Connection data Connection method Screw connection Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 4 mm² Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 2.5 mm² Conductor cross section AWG min. 24 Conductor cross section AWG max. 12 Conductor cross section flexible, with ferrule without plastic sleeve min. 0.25 mm² Conductor cross section flexible, with ferrule without plastic sleeve max. 2.5 mm² Conductor cross section flexible, with ferrule with plastic sleeve min. 0.25 mm² Conductor cross section flexible, with ferrule with plastic sleeve max. 2.5 mm² Cross section with insertion bridge, solid max. 4 mm² Cross section with insertion bridge, stranded max. 2.5 mm² 2 conductors with same cross section, solid min. 0.2 mm² 2 conductors with same cross section, solid max. 1 mm² 05/05/2016   Page 2 / 6 https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Technical data Connection data 2 conductors with same cross section, stranded min. 0.2 mm² 2 conductors with same cross section, stranded max. 1 mm² 2 conductors with same cross section, stranded, ferrules without plastic sleeve, min. 0.25 mm² 2 conductors with same cross section, stranded, ferrules without plastic sleeve, max. 1 mm² 2 conductors with same cross section, stranded, TWIN ferrules with plastic 0.5 mm² sleeve, min. 2 conductors with same cross section, stranded, TWIN ferrules with plastic 1 mm² sleeve, max. Cross section with insertion bridge, solid max. 4 mm² Cross section with insertion bridge, stranded max. 2.5 mm² Stripping length 8 mm Internal cylindrical gage A3 Screw thread M3 Tightening torque, min 0.5 Nm Tightening torque max 0.6 Nm Standards and Regulations Connection in acc. with standard CSA IEC 60947-7-1 / IEC 60947-7-2 Flammability rating according to UL 94 V2 Classifications eCl@ss eCl@ss 4.0 27141118 eCl@ss 4.1 27141118 eCl@ss 5.0 27141118 eCl@ss 5.1 27141118 eCl@ss 6.0 27141128 eCl@ss 7.0 27141128 eCl@ss 8.0 27141128 ETIM ETIM 2.0 EC000900 ETIM 3.0 EC000900 ETIM 4.0 EC000900 ETIM 5.0 EC000900 05/05/2016   Page 3 / 6 https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Classifications UNSPSC UNSPSC 6.01 30211811 UNSPSC 7.0901 39121410 UNSPSC 11 39121410 UNSPSC 12.01 39121410 UNSPSC 13.2 39121410 Approvals Approvals Approvals CSA / UL Recognized / cUL Recognized / EAC / cULus Recognized Ex Approvals Approvals submitted Approval details CSA      mm²/AWG/kcmil 28-14 Nominal current IN 15 A Nominal voltage UN 300 V UL Recognized      mm²/AWG/kcmil 30-14 Nominal current IN 15 A Nominal voltage UN 300 V 05/05/2016   Page 4 / 6 https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Approvals cUL Recognized      mm²/AWG/kcmil 30-14 Nominal current IN 15 A Nominal voltage UN 300 V EAC  cULus Recognized  Drawings 05/05/2016   Page 5 / 6 https://www.phoenixcontact.com/us/products/2717113 Sensor/actuator terminal block - DOK 1,5-TG - 2717113 Circuit diagram Circuit diagram Phoenix Contact 2016 © - all rights reserved http://www.phoenixcontact.com 05/05/2016   Page 6 / 6