2754341

IBS ST 24 BK-T INTERBUS-S Data Sheet Bus Terminal Module 08/1994 m Data Sheet Revision A co Product Description ne nt s. The IBS ST 24 BK-T bus terminal module is the head station for an INTERBUS ST compact station in an INTERBUS-S network. on l in ec om - INTERBUS-S protocol - D-SUB 9 remote bus connectors - Electrical isolation of the remote bus segments - Electrical isolation of the logic and I/O voltage - Diagnostic LEDs - Alarm output - Reconfiguration input - Replaceable electronics - Rail mountable (EN 50022) po Features Applications Connection of an INTERBUS ST compact station to the INTERBUS-S remote bus. 50152001 Fig. 1: IBS ST 24 BK-T 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 1 Example of an Electrical Installation Incoming remote bus Outgoing remote bus PE 50152004 co m ST cable ne nt s. Fig. 2: Exemplary connection of an IB ST compact station through the IBS ST 24 BK-T bus terminal module to the INTERBUS-S remote bus. An IB ST compact station may consist of up to 8 I/O modules. om po Connect the mounting rail via ground terminals with protective earth (PE), as the modules are grounded when they are snapped onto the rail. Table 1: Ordering data Order No. Bus terminal module IBS ST 24 BK-T 27 54 34 1 Module electronics, separately IBS STME 24 BK-T 27 54 36 7 Terminal block, separately IBS STTB 24 BK-T 27 53 18 0 Fuse, 1 A, slow-blow IBS TR5 1AT 28 06 60 0 Insertion bridge, 80-pos., divisible, IN = 26A, insulated back (5 pieces) EB 80-DIK BU (blue) EB 80-DIK RD (red) 27 15 94 0 27 15 95 3 Zack (“quick“) strip for terminal labeling ZB 6 ... see Phoenix Contact Catalog, Part 3 MARKING, MOUNTING, Page 18 Mounting rail EN 50022, 2 meters NS 35/7,5 perforated NS 35/7,5 unperforated in ec Type on l Description 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 2 08 01 68 1 08 01 73 3 Connection UL + UA UREC + + To be wired externally Internally connected 9 13 14 15 16 4 5 6 7 8 E LD RD po ne nt s. UL RC BA co m 1 12 om 50272002 in ec Fig. 3: Connection of the supply voltage Supply voltage for the bus logic UA: Supply voltage for the alarm contact (optional) on l UL: Alarm set 14 15 Alarm not set and INTERBUS-S is connected 14 15 6 6 50151006 Fig. 4: Method of functioning of the alarm contact UREC: Supply voltage for the reconfiguration input (optional). This input can only be used in connection with a group definition. The reconfiguration input has the same potential as the supply voltage. That means that the terminals 9 and 16 have to be connected. 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 3 Connection Pin Assignment of the Male and Female Remote Bus Connector Outgoing remote bus 9-pos. D-SUB male connector 9 Solder side /DO DO /DI DI COM 6 1 9 5 Solder side m 5 6 1 7 2 3 green yellow pink gray brown bridged Notes on how to assemble the cable 8 ne 3 nt 20 co 6 6 1 7 DI 2 COM 3 5 9 s. 1 /DO DO /DI Incoming remote bus 9-pos. D-SUB female connector in ec om po Strip the cable sheath 20 mm and bare the core ends 3 mm. Shorten the braided screen by 12 mm. on l Place the braided screen evenly around the cable sheath Male/Female Solder side Clamp the shield under the cable grip (conductive connection with the housing). 5015A005 Fig. 5: Connector pin assignment for the incoming and outgoing remote bus with information on how to assemble the cable. In order to reduce the installation time of an INTERBUS-S systems as much as possible, Phoenix Contact offers pre-assembled bus cable in different lengths (see Phoenix Contact Catalog, Part 11: INTERBUS). 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 4 Programming Data Table 2: The most important data for the programmer 8 (decimal) 8 (hexadecimal) Length code 0 (hexadecimal) Input address area 0 bytes Output address area 0 bytes PCP address area 0 bytes Register length 0 bytes co Programmable functions Yes Reset of the IB ST compact station Yes nt Yes on l in ec om po Monitoring of the remote bus cable Yes Yes ne Reset of the outgoing remote bus s. Disconnection of the IB ST compact station Disconnection of the outgoing remote bus m Identification code 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 5 Technical Data General Type Identification code IBS ST 24 BK-T 08 (hex) 8 (dec) 0 0 IP 20 VDE 0110 part1, 01/89 From 0 °C to 55 °C From -20 °C to 70 °C 81 mm * 117 mm * 116 mm Length code Register length Degree of protection Air and creepage distances Permissible operating temperature Permissible storage temperature Housing dimensions (w * d * h) m Interfaces INTERBUS-S - Incoming remote bus - Outgoing remote bus - IB ST interface om in ec Alarm contact - Terminal points - Maximum voltage UA - Maximum current on l Reconfiguration input - Terminal points - Nominal voltage UREC - Permissible range - Current consumption (set) Supply Terminal points Nominal voltage US Permissible ripple Permissible voltage range Current consumption, primary: - without IB ST local bus modules - maximum Current output, secondary (ST cable): - maximum Internal fuse 5015A co s. nt ne 400 m Test voltage 500 V AC (50 Hz) Test voltage 500 V AC (50 Hz) po Number of the connectible ST modules Maximum distance to the next remote bus module Electrical isolation between - incoming and outgoing remote bus - incoming remote bus and IB ST interface D-SUB male connector, 9-pos. D-SUB female connector, 9-pos. ST cable (is included in the scope of delivery of the I/O modules) 8 6, 14, 15 (see Figure 3) 30 V AC/DC 0.5 A 8 (+), 18 (-) (see Figure 4) 24 V DC -30 V to +30 V (DC) set: 13 V to 30 V (DC) not set: -30 V to +1 V 2 mA typical 1 (+), 9 (-) (see Figure 3) 24 V (DC) 3.3 Vpp within the permissible voltage range 20 V to 30 V (DC) 150 mA typical (at 24 V) 650 mA typical (at 24 V) 800 mA (9 V) IBS TR 5 , 1 A (slow-blow), Order No.: 28 06 60 0 Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 6 Technical Data Local Diagnostic Indicators green LED on: off: supply voltage for the module electronics supply voltage available - supply voltage UL not available - fuse of the BK defective - internal power supply unit of the BK defective BA green LED on: off: remote bus active data transmission on INTERBUS active no data transmission RC green LED on: off: remote bus cable check incoming remote bus connection established incoming remote bus connection interrupted E red LED on: error controller board located an error in this compact station LD red LED on: compact station disabled I/O modules of this compact station disabled RD red LED on: ne nt s. co m UL on l in ec om po remote bus disabled outgoing remote bus disabled 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 7 TNR 92 65 63 9 DNR 2514 on l in ec om po ne nt s. co m Notes: 5015A Phoenix Contact GmbH & Co. Postfach 1341 32819 Blomberg Germany 8