2814854

Signal Multiplier MCR-FL-C-UI-2UI-DCI 1. Description • 4-way isolation • Configurable inputs and outputs Signal conversion and amplification • Adjustable signal combinations • 17.5 mm ME housing Isolation OUT1 FL U,I IN U, I U,I OUT2 POWER The MCR-FL-C-UI-2UI-DCI signal multiplier is used to multiply and electrically isolate analog signals. The module inputs, outputs, and the power supply are electrically isolated from one another (4-way isolation). In this way, the modules can be used for electrical isolation, signal conversion, and amplification both locally and close to the control system. The auxiliary voltage required is indicated by a green power LED. DIP switches can be used to switch between a signal selected within the limits of the order key or for the fixed signal conversions provided in the configuration table. If no entry is made in the specified order key, the devices are supplied with the default configuration (input signal 0…20 mA, output signals 0…20 mA/ 0…10 V). Adjustment following configuration is not necessary, as each transmission variant is calibrated and stored in the device. 1 1 4 ,5 9 9 Headquarters: © Phoenix Contact GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany Phone +49 - 52 35 - 30 0 • Fax +49 - 52 35 - 34 12 00 • www.phoenixcontact.com Local Contact: www.phoenixcontact.com/salesnetwork 1 7 ,5 Signal Multiplier – MCR-FL-C-UI-2UI-DCI 2. Technical Data OUT OUT I2 OUT U2 GND 2 IN I IN U GND 3 1 2 3 OUT A D D 4 5 6 A 7 OUT I1 8 OUT U1 9 GND 1 0 +24V DC ! GND 4 " GND 4 A D IN MCR-FL-C-UI-2UI-DCI with configurable input and output 8 mm M3 Solid Connection data Stranded [mm2] AWG 0.2 - 2.5 uU 0.2 - 2.5 25 - 14 Description MCR signal multiplier, for doubling and electrical isolation of analog signals Preconfigured Not configured Type Order No. MCR-FL-C-UI-2UI-DCI MCR-FL-C-UI-2UI-DCI-NC 28 14 85 4 28 14 86 7 Pcs. Pkt. Technical Data Input Input signal range Measuring range span Maximum input signal Input resistance 0…24 mA/0…12 V, freely selectable in increments of 0.1 (mA/V) 8 mA/4 V, minimum 50 mA or 30 V 50 Ω at I input/200 kΩ at U input Output Output signal per channel Maximum output signal per channel Load per channel See order key/configuration table 35 mA or 15 V ≤ 600 Ω at I output/≥ 10 kΩ at U output General Data Supply voltage Current consumption (without load) Transmission error Temperature coefficient Limit frequency (3 dB) Step response (10 - 90%) Test voltage Protective circuit Ambient operating temperature range Degree of protection Connection method Mounting position/mounting Electromagnetic compatibility: • Noise emission • Noise immunity 20…30 V DC < 25 mA < 0.15% of the final value; 0.05% of the final value, typical < 0.015%/K, 0.0075%/K, typical 30 Hz 12 ms 1.5 kV AC, 50 Hz, 1 minute Transient protection -20°C to +55°C IP20 Plug-in COMBICON screw terminal block Any c Conformance with EMC Directive 89/336/EEC EN 50 081-2 EN 50 082-2 PHOENIX CONTACT page 2 of 5 1 1 Signal Multiplier – MCR-FL-C-UI-2UI-DCI c Conformance With EMC Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC EMC (Electromagnetic Compatibility) Noise Immunity According to EN 50082-2 • Electrostatic discharge (ESD) 8 kV air discharge 2) EN 61000-4-2 • Electromagnetic HF field Amplitude modulation Pulse modulation EN 61000-4-3 • Fast transients (burst) EN 61000-4-4 Input/output/supply 2 kV/5 kHz 2) • Surge current loads (surge) EN 61000-4-5 Input/output: 2 kV/42 Ω 2) Supply: 0.5 kV/2 Ω/12 Ω 2) • Conducted interference EN 61000-4-6 Input/output/supply 10 V 1) 10 V/m 1) 10 V/m 1) EN 55011 Noise Emission According to EN 50081-2 Class A EN 61000 corresponds to IEC 1000/ EN 55011 corresponds to CISPR11 1) Criterion A: Normal operating characteristics within the specified limits. 2) Criterion B: Temporary adverse effects on the operating characteristics which the device corrects automatically. Class A: Approval Industrial application, without special installation measures. U PROCESS CONTROL EQUIPMENT FOR HAZARDOUS LOCATIONS 31ZN LISTED Cl. I, Zn. 2, AEx nC IIC T6 / Ex nC IIC T6 Cl. I Div. 2, Groups A, B, C and D A) This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous locations only. B) Warning - explosion hazard - substitution of components may impair suitability for Class 1, Division 2. C) Warning - explosion hazard - do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous. MCR-FL-C-UI-2UI-DCI – Signal Multiplier 2 I 4 R E W O P I-2 -U -C FL R- MC U CI D UI- R D E GN 1 W 4 D N O D P GN T1 G U O 4V +2 1 1 Upper housing part, can be removed to set DIP switches 2 I U T U O I 2 Plug-in screw terminal blocks G IN D U N 2 G N D 3 I DC UII-2 4 -U 85 -C 14 FL 8 R-r.: 2 C N Mrt.T OU A OU 7 OU 8 GN 9 D A 0 ! " 1 2 3 Metal lock for fastening on the DIN rail 3 OU 4 T 5 6 2 A I2 U2 2 1 2 3 A 4 5 6 IN 1 2 3 IN 4 IN 5 I1 8 T 1 OU U 9 T OU 1 10 D N DC 1 G 1 4V 2 + 4 D 12 N G 4 D GN D I2 T 2 OU U T OU 2 D GN S AL OV I PR U D GN 6 D 7 D 3 N / AP NE TIO BA O PR AP 3 Fig. 06 PHOENIX CONTACT page 3 of 5 Signal Multiplier – MCR-FL-C-UI-2UI-DCI 3. Configuration -D UI I-2 -U -C FL R- MC O I 3.1. Opening the Device (Fig. 07) The fastenings on both sides of the upper housing part can be released using a screwdriver 1. The upper housing part and the electronics can now be pulled out about 3 cm 2. U U 2 T I G IN N D U 2 G N D 3 1 2 FL R-r.: N MrC t.- 3 A 2 Ensure you take sufficient measures against electrostatic discharge OU 4 T 5 6 1 A I2 U2 2 D 1 2 3 A D D 4 5 6 N I I2 T 2 OU U T OU 2 2 D GN 3 I IN P 4 AP U / IN 3 5 EN D 1 Fig. 07 3.2. Setting (Fig. 08) Changes to the ordered connection method settings are made via DIP switches S1 to S10. In addition to the preconfigured signal, which is preset by the order key, the remaining 9 DIP switches and their signal behavior can be enabled using DIP switch 10. DIP 10 9 Configuration S10 8 Signal range specification via DIP switches OFF 7 Signal ranges preset by order key ON 6 5 Input (IN) S1 S2 S3 4 0…20 mA OFF OFF OFF 3 0…10 mA OFF OFF ON 2 4…20 mA OFF ON OFF 1 2…10 mA OFF ON ON 0…10 V ON OFF OFF 1…5 V ON OFF ON 0…5 V ON ON OFF 2…10 V ON ON ON Output 1: Setting the output signal ranges Setting the input signal range Fig. 08 The current and voltage channel can be used in parallel at each output so that up to four signal outputs with full load capability are provided. Please note: Where possible, output 1 should be used as a current output. Output: Current/Voltage Signal DIP Switch Function Signal range specification according to the order key or DIP switches Output 2: Setting the output signal ranges Output 1 (OUT 1) Output 2 (OUT 2) S4 S5 S6 S7 S8 S9 0…20 mA / 0…10 V OFF OFF OFF OFF OFF OFF 0…20 mA / 1…5 V OFF OFF ON OFF OFF ON 0…20 mA / 0…5 V OFF ON OFF OFF ON OFF 0…10 mA / 0…5 V OFF ON ON OFF ON ON 4…20 mA / 0…10 V ON OFF OFF ON OFF OFF 4…20 mA / 1…5 V ON OFF ON ON OFF ON 4…20 mA / 0…5 V ON ON OFF ON ON OFF 4…20 mA / 2…10 V ON ON ON ON ON ON If the value is outside the measuring range, a linear transmission response is triggered. PHOENIX CONTACT page 4 of 5 Signal Multiplier – MCR-FL-C-UI-2UI-DCI 4. Application Example (Fig. 09) Level measurement with ultrasound and subsequent signal multiplication 15 m3 0…20 mA 0…10 V Control system IN OUT2 1 I2 5 U 2 U2 6 GND3 3 GND2 MCR-FL-C-UI-2UI-DCI POWER 4 I OUT1 I1 7 POWER +24V 10 U1 8 GND4 11 GND1 9 GND4 12 Ultrasonic transmitter/sensor 0…20 mA 24V 24V 5. Order Key Mains voltage MCR-FL-C-UI-2UI-DCI The standard configuration will be supplied if customer order details are incorrect or not provided (provided in the order key as an example). Input Signal 28 14 85 4 Standard configuration I I = Current U = Voltage Input Signal (Standard and Special Signals) Start Value Final Value 0.0 I = 0.0 mA I: Freely selectable between U: Freely selectable between 20.0 I = 20.0 mA I: Freely selectable between U: Freely selectable between • Minimum measuring range span 8.0 mA/4.0 V 2) • Increment 0.1 mA/0.1 V ) Order examples: 28 14 85 4 Input Signal (Standard and Special Signals) Start Value Final Value I I = Current 5.3 I = 5.3 mA 13.3 I = 13.3 mA OUT01 OUT01 = 0...20 mA OUT02 = 4...20 mA OUT03 = 0...10 V OUT04 = 2...10 V OUT05 = 0...5 V OUT06 = 1...5 V OUT16 = 0...10 mA Output Signal Output 1 OUT01 OUT01 = 0...20 mA OUT02 = 4...20 mA OUT03 = 0...10 V OUT04 = 2...10 V OUT05 = 0...5 V OUT06 = 1...5 V OUT16 = 0...10 mA Output 2 OUT01 OUT01 OUT01 OUT03 Measuring range span 8.0 mA, i.e., can be ordered. 7.8 11.8 I = 7.8 V I = 11.8 V Measuring range span 4.0 V, i.e., can be ordered. TNR: 5106352-01 U U = Voltage 03/15/05 28 14 85 4  PHOENIX CONTACT 2 Output Signal (Standard Signals) Output 1 Output 2 http://www.phoenixcontact.com Order No. Fig. 09 PHOENIX CONTACT page 5 of 5