2832690

FL PF/SEC 2/8TX Patch Box and Patch Angle for Ethernet Installation AUTOMATIONWORX Data Sheet © PHOENIX CONTACT - 11/2005 Description – – – – – – The Factory Line patch fields (patch angle / box) are Ethernet connection fields replacing the on-site assembly of RJ45 connectors. The field cabling is connected to the patch field without using tools. Pre-assembled patch cables realize the connection to the termination device or distributor. The patch field can either be latched onto a DIN rail or it can be mounted directly onto a panel. When first put into operation, it is possible to retrofit unoccupied slots without interrupting operation of the installed ports. In the lower part of the patch angles, cable ducts are integrated so that each installed cable can be clearly routed and strain-relieved using cable clips. All components meet the latest requirements of international standards. Especially with regard to the "4-connector channel" in industrial environments where more than 2 passive coupling points are realized between 2 active components, full compatibility is given. – – Security functions on layer 1 can be realized via accessories included in this shipment. If required, further accessories are available as (FL SEC PAC 4TX) set for four RJ45 ports. Optionally, any port can be retrofitted so that SCRJ connections can be patched. Here, the SCRJ patch (see technical data / ordering data) is required. Applications The FL PF SEC 2/8TX is a patch field for industrial applications. The robust patch field can be mounted onto a DIN rail or directly onto a level surface without using any tools. Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. This data sheet is valid for the following products listed on the following page: 7255_en_00 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00 • www.phoenixcontact.com www.phoenixcontact.com/salesnetwork 1 FL PF/SEC 2/8TX Ordering Data Products Description Type Order No. Patch angle with 2 ports in Cat5E FL PF 2TX CAT5E 28 91 16 5 1 Patch angle with 8 ports in Cat5E FL PF 8TX CAT5E 28 91 17 8 1 Patch angle with 2 ports in Cat6 FL PF 2TX CAT6 28 91 06 8 1 Patch angle with 8 ports in Cat6 FL PF 8TX CAT6 28 91 07 1 1 Patch angle with security elements for 2 ports in CAT5E FL PF SEC 2TX 28 32 68 7 1 Patch angle with security elements for 8 ports in CAT5E FL PF SEC 8TX 28 32 69 0 1 Accessories Description Type Order No. Pcs./Pkt. Security set for 4 RJ45 ports FL SEC PAC 4TX 28 32 86 5 4 Using an SCRJ patch VS SCRJ-GOF-KU 16 54 35 8 1 Gray RJ45 connector set for linear cable FL PLUG RJ45 GR/2 27 44 85 6 2 Green RJ45 connector set for crossed cable FL PLUG RJ45 GN/2 27 44 57 1 2 Universal end clamp E/NS 35 N 08 00 88 6 50 Assembly tool for RJ45 connector FL CRIMPTOOL 27 44 86 9 1 Startup / diagnostic software - Factory Manager FL SWT 28 31 04 4 1 Network monitoring with HMI/SCADA systems FL SNMP OPC SERVER 28 32 16 6 1 Pcs./Pkt. Patch box 8 x RJ45 CAT5e, pre-assembled, can be retrofitted FL PBX 8TX 28 32 49 6 1 Patch box 6 x RJ45 CAT5e and 4 SC-RJ, glass pre-assembled, can be retrofitted FL PBX 6TX/4FX 28 32 50 6 1 SCRJ patch cable on SC duplex 1 m VS-PC-2X-GOD-50-SCRJ/SCDU-1 16 54 40 0 1 Patch cable, CAT 5, pre-assembled, 0.3 m long FL CAT5 PATCH 0,3 28 32 25 0 10 Patch cable, CAT 5, pre-assembled, 0.5 m long FL CAT5 PATCH 0,5 28 32 26 3 10 Patch cable, CAT 5, pre-assembled, 1.0 m long FL CAT5 PATCH 1,0 28 32 27 6 10 Patch cable, CAT 5, pre-assembled, 1.5 m long FL CAT5 PATCH 1,5 28 32 22 1 10 Patch cable, CAT 5, pre-assembled, 2.0 m long FL CAT5 PATCH 2,0 28 32 28 9 10 Patch cable, CAT 5, pre-assembled, 3.0 m long FL CAT5 PATCH 3,0 28 32 29 2 10 Patch cable, CAT 5, pre-assembled, 5.0 m long FL CAT5 PATCH 5,0 28 32 58 0 10 Patch cable, CAT 5, pre-assembled, 7.5 m long FL CAT5 PATCH 7,5 28 32 61 6 10 Patch cable, CAT 5, pre-assembled, 10.0 m long FL CAT5 PATCH 10 28 32 62 9 10 Technical Data General Data Transmission speed 100 Mbps, up to 1,000 Mbps for CAT6 Connection cable Twisted pair, shielded, CAT5 or better Transmission length 80 m plus 2 x 10 m patch cable Connector RJ45 Cable cross section 10 mm, max. Admissible wire diameter 0.5 up to 0.65 mm Admissible insulation diameter 0.8 up to 1.6 mm Insertion/withdrawal cycles More than 750 Connection cycles of the installation cable More than 20 Dimensions in mm (W x H x D) 38 x 115 x 87 (FL PF SEC 2TX) 124 x 130 x 138 (FL PF SEC 8TX) 35 x 115 x 87 (FL PF 2TX CAT5e) 35 x 115 x 87 (FL PF 2TX CAT6) 124 x 130 x 138 (FL PF 8TX CAT6) 124 x 130 x 138 (FL PF SEC 8TX) 7255_en_00 PHOENIX CONTACT 2 FL PF/SEC 2/8TX Security Elements With the help of the security accessories, the security can be realized on layer 1. Security accessories prevent the disconnection of a patch cable as well as unauthorized access onto non-occupied ports by unauthorized persons. Plugged connections and covers can only be removed by authorized persons. The scope of supply of the FL PF SEC 2/8TX patch fields also includes the security accessories. Further patch fields and boxes can be retrofitted using the FL SEC PAC 4TX set. This set contains all necessary elements to secure 4 TX ports. Installation and Mounting/Removal Install the patch field on a clean DIN rail. End clamps can be mounted on both sides of the module to stop the modules from slipping on the DIN rail. Mounting: • • • Place the module onto the DIN rail from above. The upper holding keyway of the module must be hooked onto the top edge of the DIN rail. Push the module from the front towards the mounting surface. Once the module has been snapped on properly, check that it is fixed securely on the DIN rail. Removal: • • Pull the module towards you, away from the mounting surface. Lift the module from the DIN rail. Terminal Assignment Color coding of the IDC terminal blocks at the RJ45 sockets. Figure 1 Conductor Pair Preparation Color coding of the sockets Figure 2 7255_en_00 Conductor pair preparation PHOENIX CONTACT 3 FL PF/SEC 2/8TX Connecting the Conductors to the IDC Terminal Blocks Figure 3 Connecting the conductors to the IDC terminal blocks © PHOENIX CONTACT 11/2005 7255_en_00 PHOENIX CONTACT 4