2878421

ILB IB 24 DI16-DSUB Inline Block IO Module for INTERBUS With 16 Digital Inputs; Bus Connection via D-SUB Connectors AUTOMATIONWORX Data Sheet 7118_en_02 © PHOENIX CONTACT - 03/2007 Description The ILB IB 24 DI16-DSUB module is designed for use within an INTERBUS network. It is used to acquire digital signals. INTERBUS Features – – – Remote bus connection via D-SUB connector 500 kbps transmission speed Diagnostic and status indicators Input Features – – – – – Connections for 16 digital sensors Connection of sensors in 2 and 3-wire technology Maximum permissible load current per sensor: 125 mA Maximum permissible load current from the sensor supply: 2.0 A Diagnostic and status indicators Please refer to the "Mounting and Removing Inline Block IO Modules" application note (see "Ordering Data" on page 2). Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. ILB IB 24 DI16-DSUB Ordering Data Product Description Type Order No. Pcs./Pkt. ILB IB 24 DI16-DSUB 2878421 1 Accessories: Connectors Description Type Order No. Pcs./Pkt. D-SUB connector (female connector), solder connection SUBCON 9/F-SH 2761499 1 D-SUB connector (male connector), solder connection SUBCON 9/M-SH 2761509 1 Accessories: Connectors as Replacement Item Description Type Order No. Pcs./Pkt. Connector for the supply (4-pos. MINI COMBICON) FK-MCP 1,5/5-STF-3,81 1851258 50 Connector for the supply (5-pos. MINI COMBICON) FK-MCP 1,5/6-STF-3,81 1851261 50 Connector for digital 4-channel or 16-channel Inline input terminals, with color print IB IL SCN-12-ICP 2727611 10 Inline Block IO module for INTERBUS with 16 digital inputs; bus connection via D-SUB connectors Accessories: Other Description Type Order No. Pcs./Pkt. CLIPFIX 35-5 3022276 50 Documentation Description Type Order No. Pcs./Pkt. "Mounting and Removing Inline Block IO Modules" application note AH ILB INSTALLATION 9014931 1 1 Recommended end clamp; placed both to the right and left of the module to secure it on the DIN rail "INTERBUS Addressing" data sheet DB GB IBS SYS ADDRESS 9000990 "Addressing of 16-Channel ILB Modules" application note AH ILB 24 DI/DO 16 ADDRESS 9014962 1 "General Introduction to the INTERBUS System" user manual IBS SYS INTRO G4 UM E 2745211 1 "Configuring and Installing INTERBUS" user manual IBS SYS PRO INST UM E 2743802 1 7118_en_02 PHOENIX CONTACT 2 ILB IB 24 DI16-DSUB Technical Data General Data Housing dimensions with connectors (width x height x depth) 95 mm x 55 mm x 141 mm Weight 254 g (with connectors) Operating mode Process data mode with 1 word Transmission speed 500 kbps Connection method for sensors 2 and 3-wire technology Housing Dimensions 95 141 120 55 7118B003 Figure 1 Housing dimensions of the module (dimensions in mm) Ambient Conditions Regulations Developed according to VDE 0160/EN 50178/IEC 62103, UL 508 Ambient temperature (operation) -25°C to +60°C Ambient temperature (storage/transport) -25°C to +85°C Humidity (operation/storage/transport) 10% to 95%, according to EN 61131-2 Air pressure (operation) 80 kPa to 108 kPa (up to 2000 m above sea level) Air pressure (storage/transport) 66 kPa to 108 kPa (up to 3500 m above sea level) Degree of protection according to IEC 60529 IP20 Class of protection Class 3 according to VDE 0106/IEC 60536 Air and creepage distances According to DIN VDE 0110/IEC 60664, IEC 60664A, DIN VDE 0160/EN 50178/IEC 62103 Housing material Plastic, PVC-free, PBT, self-extinguishing (V0) Pollution degree according to EN 60664-1/IEC 60664-1, EN 61131-2/IEC 61131-2 2; condensation not permitted during operation Surge voltage class II 7118_en_02 PHOENIX CONTACT 3 ILB IB 24 DI16-DSUB Electrical Isolation/Isolation of the Voltage Areas Test Distance Test Voltage Incoming remote bus / outgoing remote bus 500 V AC, 50 Hz, 1 min Incoming remote bus / I/O 500 V AC, 50 Hz, 1 min Incoming remote bus / functional earth ground 500 V AC, 50 Hz, 1 min Outgoing remote bus / I/O 500 V AC, 50 Hz, 1 min Outgoing remote bus / functional earth ground 500 V AC, 50 Hz, 1 min I/O / functional earth ground 500 V AC, 50 Hz, 1 min Mechanical Requirements Vibration test, sinusoidal vibrations according to EN 60068-2-6/IEC 60068-2-6 5g load, 2.5 hours in each space direction Shock test according to EN 60068-2-27/IEC 60068-2-27 25g load for 11 ms, half sinusoidal wave, 3 shocks in each space direction and orientation Broadband noise according to EN 60068-2-64/IEC 60068-2-64 0.78g load, 2.5 hours in each space direction Conformance With EMC Directive 89/336/EEC Noise Immunity Test According to EN 61000-6-2 Electrostatic discharge (ESD) EN 61000-4-2 IEC 61000-4-2 Criterion B Electromagnetic fields EN 61000-4-3 IEC 61000-4-3 Criterion A Fast transients (burst) EN 61000-4-4/ IEC 61000-4-4 Criterion B 6 kV contact discharge 8 kV air discharge Field strength: 10 V/m Remote bus: 2 kV Power supply: 2 kV I/O cables: 2 kV Criterion A All interfaces: 1 kV Surge voltage EN 61000-4-5 IEC 61000-4-5 Criterion B DC supply lines: ± 0.5 kV/± 1.0 kV (symmetrical/asymmetrical) Signal lines: ± 0.5 kV/± 0.5 kV (symmetrical/asymmetrical) Conducted interference EN 61000-4-6 IEC 61000-4-6 Criterion A Test voltage 10 V Noise Emission Test According to EN 61000-6-4 Noise emission of housing EN 55022 Class B (residential) Interface: INTERBUS Incoming remote bus Copper cable (RS-422), connected via 9-pos. D-SUB connector; supply electrically isolated; shielding connected with a capacitor to functional earth ground Outgoing remote bus Copper cable (RS-422), connected via 9-pos. D-SUB connector; supply electrically isolated; shielding directly connected to functional earth ground Recommended cable lengths See INTERBUS system data in the IBS SYS INTRO G4 UM E user manual 7118_en_02 PHOENIX CONTACT 4 ILB IB 24 DI16-DSUB 24 V Module Supply (Communications Power and Sensor Supply; UL and US) Nominal value 24 V DC Tolerance -15%/+20% according to EN 61131-2 Ripple ±5% according to EN 61131-2 Permissible range 19.2 V DC to 30.0 V DC Current consumption at UL 60 mA Current consumption at US 4A Safety equipment for communications power Surge protection and protection against polarity reversal Safety equipment for sensor supply Surge, overload and short-circuit protection Connection Via MINI-COMBICON connector Digital Inputs Number 16 Connection method for sensors 2 and 3-wire technology Input design According to EN 61131-2 Type 1 Definition of switching thresholds Maximum low-level voltage ULmax < 5 V Minimum high-level voltage UHmin > 15 V Common potentials Sensor supply US, ground Nominal input voltage UIN 24 V DC Permissible range -30 V < UIN < +30 V DC Nominal input current for UIN 5 mA, typical Current flow Linear in the range 1 V < UIN < 30 V Delay time ≤ 500 µs Permissible cable length to the sensor 100 m Use of AC sensors AC sensors in the voltage range < UIN are limited in application Power Dissipation Formula to Calculate the Power Dissipation of the Electronics 2 n PTOT = 1.44 W + IS x 0.06 W + S 0.12 W i=1 Where PTOT IS i n Total power dissipation of the module Current from the sensor supply Continuous index Number of set inputs (n = 1 to 16) Limitation of Simultaneity, Derating No limitation of simultaneity, no derating Approvals For the latest approvals, please visit www.download.phoenixcontact.com. 7118_en_02 PHOENIX CONTACT 5 ILB IB 24 DI16-DSUB Internal Circuit Diagram U L B A R C Local Diagnostic and Status Indicators R D IN B U S E 1 1 1 2 O P C 8 x 8 x U L B A R C R D I1 1 2 3 2 3 4 I2 2 3 4 I3 4 3 I4 4 5 V 2 4 V D I1 ...8 U U L D I9 ..1 6 U S S U L U S IN T E R B U S E P W R 1 6 x IN Figure 3 7 1 1 8 A 0 0 5 Diagnostic and status indicators of the ILB IB 24 DI16-DSUB module 7 1 1 8 B 0 0 2 Figure 2 Internal wiring of the terminal points Designation Color Meaning UL Green Communications power RC Green Remote bus cable check BA Green Bus active RD Yellow Outgoing remote bus disabled E Red US Green E Red Short circuit or overload of the sensor supply 1 to 4 Yellow Status indicators of the inputs BUS Key: LED OPC Protocol chip (bus logic) PWR x x x Power supply unit with electrical isolation X X X Undervoltage of the sensor supply US Sensor supply IN Optocoupler Short-circuit-proof sensor supply 7118_en_02 PHOENIX CONTACT 6 ILB IB 24 DI16-DSUB Connecting INTERBUS, the Supply, and Sensors 1 .1 1 . X 1 U L U S N C N C 1 .2 X 2 1 1 .3 0 V 0 V N C N C F E 1 .4 1 2 1 .1 2 .1 1 .2 2 .2 1 .3 2 .3 1 .4 2 .4 1 .5 2 .5 1 .5 1 .6 Terminal Point UL US NC NC 2 .1 2 .2 2 .3 2 .4 2 .5 1 .6 2 .6 2 .6 5 -8 R E M O T E O U T R E M O T E IN IL B IB 2 4 D I1 6 -D S U B d e r -N o .: 2 8 7 8 4 X 3 X 4 7 1 1 8 C 0 0 6 Figure 4 Terminal Point Assignment of the MINI-COMBICON Connectors for the Connection of the Supply Voltages (Connectors X1 and X2 in Figure 4 on page 7). Terminal point assignment of the connectors Terminal Point 0V 0V NC NC FE Assignment 24 V communications power UL 24 V sensor supply US Not used Not used Assignment GND GND Not used Not used Functional earth ground The terminal points for GND (0V) can have a total current of 8 A per terminal point. The maximum current carrying capacity of 8 A must not be exceeded. The supply points have the same ground potential. All ground supplies on a module are electrically connected with one another. The communications power is also electrically connected via all contacts. In this way it can supply all potentials with just one supply without the need for additional terminals, see "Connection example" on page 9. 7118_en_02 PHOENIX CONTACT 7 ILB IB 24 DI16-DSUB Terminal Point Assignment of the INTERBUS Connectors (Connectors X 3 and X4 in Figure 4 on page 7) 6 1 7 1 6 2 8 5 9 re 3 9 4 5 n o re re A B D O D O D I D I s e rv e G N D t c o n s e rv e s e rv e D O D O D I D I s e rv G N D t c o s e rv s e rv re d n o re re n . d d 6 1 7 2 3 n n . e d e d 1 6 8 e d 9 5 9 4 5 7 1 1 7 B 0 1 2 Figure 5 A B Assignment of the remote bus interfaces (DSUB connector) Remote OUT (outgoing remote bus) Remote IN (incoming remote bus) Assignment Remark/Wire Color in the INTERBUS Standard Cable Receive Green DO DO Receive Yellow Transmit Pink DI DI Transmit Gray GND Reference potential Brown Shield Shield potential is connected with a (incoming capacitor to functional earth ground (FE) of remote bus) the potential jumper. Shield Shield potential is directly connected to (outgoing functional earth ground (FE) of the potential remote bus) jumper. In order to assemble the connectors, proceed as described in the IBS SYS PRO INST UM E user manual. Terminal Point Assignment of the Input Connectors (Connectors 5 to 8 in Figure 4 on page 7) Terminal Point Assignment Connector 5 (I1) Connector 6 (I2) Connector 7 (I3) Connector 8 (I4) 1.1, 2.1 1.1, 2.1 1.1, 2.1 1.1, 2.1 Signal input (IN) 1.2, 2.2 1.2, 2.2 1.2, 2.2 1.2, 2.2 Sensor supply for 2 and 3-wire termination 1.3, 2.3 1.3, 2.3 1.3, 2.3 1.3, 2.3 Ground contact (GND) for 3-wire termination 1.4, 2.4 1.4, 2.4 1.4, 2.4 1.4, 2.4 Signal input (IN) 1.5, 2.5 1.5, 2.5 1.5, 2.5 1.5, 2.5 Sensor supply for 2 and 3-wire termination 1.6, 2.6 1.6, 2.6 1.6, 2.6 1.6, 2.6 Ground contact (GND) for 3-wire termination 7118_en_02 PHOENIX CONTACT 8 ILB IB 24 DI16-DSUB Connection Example 5 IN 1 4 F E IN 1 5 + 8 + 2 4 V U S 7 + 2 4 V U 6 L 7 1 1 8 A 0 1 0 Figure 6 Connection example The numbers above the module illustration identify the connector slots. When connecting the sensors observe the assignment of the terminal points to the process data (see "Process Data" on page 10). The module has an FE spring (metal clip) on the bottom of the electronics base. This spring creates an electrical connection to the DIN rail. Use grounding terminals to connect the DIN rail to protective earth ground. The module is grounded when it is snapped onto the DIN rail. To ensure reliable functional earth grounding of the module even when the DIN rail is dirty or the metal clip is damaged, Phoenix Contact also recommends grounding the module via one of the FE terminal points. 7118_en_02 PHOENIX CONTACT 9 ILB IB 24 DI16-DSUB Programming Data ID code 02hex (02dec) Length code 01hex Process data channel 16 bits Input address area 1 word Output address area 0 words Parameter channel (PCP) 0 words Register length (bus) 1 word Process Data For the assignment of the illustrated (byte.bit) view to your control or computer system, please refer to the DB GB IBS SYS ADDRESS data sheet. Please refer to the application note for addressing 16-channel ILB modules. The documentation can be downloaded at www.download.phoenixcontact.com. Assignment of the Terminal Points to the IN Process Data Word (Slots 5 to 8) (Word.bit) view Word Bit (Byte.bit) view Byte Bit Module Slot Terminal point (signal) Terminal point (+24 V) Terminal point (GND) Status indicator Slot LED 15 7 14 13 12 11 Byte 0 4 3 10 9 Word 0 8 7 6 5 4 3 Byte 1 4 3 2 1 0 6 5 2 1 0 7 6 5 2 1 0 6 (I2) 5 (I1) 8 (I4) 7 (I3) 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 6 5 8 7 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 Diagnostics Error Table With Diagnostic Data and Status Indicators Error Type Sensor voltage US too low Diagnostic Data I/O error message Sensor supply short circuit I/O error message Status Indicators US LED is OFF E (PWR) LED is red E (IN) LED of the sensor supply is red © PHOENIX CONTACT 03/2007 7118_en_02 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00 www.phoenixcontact.com 10