2878528

ILB IB 24 DO16-DSUB Inline Block IO Module for INTERBUS With 16 Digital Outputs; Bus Connection via D-SUB Connectors AUTOMATIONWORX Data Sheet 7119_en_02 © PHOENIX CONTACT - 03/2007 Description The ILB IB 24 DO16-DSUB module is designed for use within an INTERBUS network. It is used to output digital signals. INTERBUS Features – – – Remote bus connection via D-SUB connector 500 kbps transmission speed Diagnostic and status indicators Output Features – – – – – – Connections for 16 digital actuators Connection of actuators in 2 and 3-wire technology Nominal current per output: 0.5 A Total current of all outputs: 8 A Short-circuit and overload protected outputs Diagnostic and status indicators Please refer to the "Mounting and Removing Inline Block IO Modules" application note (see "Ordering Data" on page 2). Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. ILB IB 24 DO16-DSUB Ordering Data Product Description Type Order No. Pcs./Pkt. ILB IB 24 DO16-DSUB 2878528 1 Accessories: Connectors Description Type Order No. Pcs./Pkt. D-SUB connector (female connector), solder connection SUBCON 9/F-SH 2761499 1 D-SUB connector (male connector), solder connection SUBCON 9/M-SH 2761509 1 Accessories: Connectors as Replacement Item Description Type Order No. Pcs./Pkt. Connector for the supply (4-pos. MINI COMBICON) FK-MCP 1,5/5-STF-3,81 1851258 50 Connector for the supply (5-pos. MINI COMBICON) FK-MCP 1,5/6-STF-3,81 1851261 50 Connector for digital 4-channel or 16-channel Inline output terminals, with color print IB IL SCN-12-OCP 2727624 10 Inline Block IO module for INTERBUS with 16 digital outputs; bus connection via D-SUB connectors Accessories: Other Description Type Order No. Pcs./Pkt. CLIPFIX 35-5 3022276 50 Documentation Description Type Order No. Pcs./Pkt. "Mounting and Removing Inline Block IO Modules" application note AH ILB INSTALLATION 9014931 1 1 Recommended end clamp; placed both to the right and left of the module to secure it on the DIN rail "INTERBUS Addressing" data sheet DB GB IBS SYS ADDRESS 9000990 "Addressing of 16-Channel ILB Modules" application note AH ILB 24 DI/DO 16 ADDRESS 9014962 1 "General Introduction to the INTERBUS System" user manual IBS SYS INTRO G4 UM E 2745211 1 "Configuring and Installing INTERBUS" user manual IBS SYS PRO INST UM E 2743802 1 "Configuring and Installing the INTERBUS Inline Product Range" user manual IB IL SYS PRO UM E 2743048 1 7119_en_02 PHOENIX CONTACT 2 ILB IB 24 DO16-DSUB Technical Data General Data Housing dimensions with connectors (width x height x depth) 95 mm x 55 mm x 141 mm Weight 254 g (with connectors) Operating mode Process data mode with 1 word Transmission speed 500 kbps Connection method for actuators 2 and 3-wire technology Housing Dimensions 9 5 1 4 1 1 2 0 5 5 7 1 1 9 A 0 0 3 Figure 1 Housing dimensions of the module (dimensions in mm) Ambient Conditions Regulations Developed according to VDE 0160/EN 50178/IEC 62103, UL 508 Ambient temperature (operation) -25°C to +60°C Ambient temperature (storage/transport) -25°C to +85°C Humidity (operation/storage/transport) 10% to 95%, according to EN 61131-2 Air pressure (operation) 80 kPa to 108 kPa (up to 2000 m above sea level) Air pressure (storage/transport) 66 kPa to 108 kPa (up to 3500 m above sea level) Degree of protection according to IEC 60529 IP20 Class of protection Class 3 according to VDE 0106/IEC 60536 Air and creepage distances According to DIN VDE 0110/IEC 60664, IEC 60664A, DIN VDE 0160/EN 50178/IEC 62103 Housing material Plastic, PVC-free, PBT, self-extinguishing (V0) Pollution degree according to EN 60664-1/IEC 60664-1, EN 61131-2/IEC 61131-2 2; condensation not permitted during operation Surge voltage class II 7119_en_02 PHOENIX CONTACT 3 ILB IB 24 DO16-DSUB Electrical Isolation/Isolation of the Voltage Areas Test Distance Test Voltage Incoming remote bus / outgoing remote bus 500 V AC, 50 Hz, 1 min Incoming remote bus / I/O 500 V AC, 50 Hz, 1 min Incoming remote bus / functional earth ground 500 V AC, 50 Hz, 1 min Outgoing remote bus / I/O 500 V AC, 50 Hz, 1 min Outgoing remote bus / functional earth ground 500 V AC, 50 Hz, 1 min I/O / functional earth ground 500 V AC, 50 Hz, 1 min Mechanical Requirements Vibration test, sinusoidal vibrations according to EN 60068-2-6/IEC 60068-2-6 5g load, 2.5 hours in each space direction Shock test according to EN 60068-2-27/IEC 60068-2-27 25g load for 11 ms, half sinusoidal wave, 3 shocks in each space direction and orientation Broadband noise according to EN 60068-2-64/IEC 60068-2-64 0.78g load, 2.5 hours in each space direction Conformance With EMC Directive 89/336/EEC Noise Immunity Test According to EN 61000-6-2 Electrostatic discharge (ESD) EN 61000-4-2 IEC 61000-4-2 Criterion B Electromagnetic fields EN 61000-4-3 IEC 61000-4-3 Criterion A Fast transients (burst) EN 61000-4-4/ IEC 61000-4-4 Criterion B 6 kV contact discharge 8 kV air discharge Field strength: 10 V/m Remote bus: 2 kV Power supply: 2 kV I/O cables: 2 kV Criterion A All interfaces: 1 kV Surge voltage EN 61000-4-5 IEC 61000-4-5 Criterion B DC supply lines: ± 0.5 kV/± 1.0 kV (symmetrical/asymmetrical) Signal lines: ± 0.5 kV/± 0.5 kV (symmetrical/asymmetrical) Conducted interference EN 61000-4-6 IEC 61000-4-6 Criterion A Test voltage 10 V Noise Emission Test According to EN 61000-6-4 Noise emission of housing EN 55022 Class B (residential) Interface: INTERBUS Incoming remote bus Copper cable (RS-422), connected via 9-pos. D-SUB connector; supply electrically isolated; shielding connected with a capacitor to functional earth ground Outgoing remote bus Copper cable (RS-422), connected via 9-pos. D-SUB connector; supply electrically isolated; shielding directly connected to functional earth ground Recommended cable lengths See INTERBUS system data in the IBS SYS INTRO G4 UM E user manual 7119_en_02 PHOENIX CONTACT 4 ILB IB 24 DO16-DSUB 24 V Module Supply (Communications Power and Actuator Supply; UL and UA) Nominal value 24 V DC Tolerance - 15%/+ 20% according to EN 61131-2 Ripple ±5% according to EN 61131-2 Permissible range 19.2 V DC to 30.0 V DC Current consumption at UL 70 mA Current consumption at UA1 and UA2 8A Safety equipment for communications power Surge protection and protection against polarity reversal Safety equipment for actuator supply Surge protection Connection Via MINI-COMBICON connector Digital Outputs Number 16 Connection method for actuators 2 and 3-wire technology Nominal output voltage UOUT 24 V DC Differential voltage at Inom ≤1V Nominal current Inom per channel 0.5 A Total current 2x4A Protection Short-circuit and overload protection Nominal load Ohmic 48 Ω / 12 W Lamp 12 W 12 VA (1.2 H, 50 Ω) Inductive Switching frequency with nominal inductive load 0.5 Hz (1.2 H, 50 Ω), maximum Overload response Auto restart Response with inductive overload Output may be damaged Reverse voltage protection against short pulses Protected against reverse voltages Resistance to permanently applied reverse voltages Protected against reverse voltages, permissible current 2 A, maximum Validity of output data after connecting the 24 V voltage supply (power up) 1 ms, typical Response upon power down The output follows the supply voltage without delay. Limitation of the voltage induced on circuit interruption -41.0 V One-time unsolicited energy 1 J, maximum Protective circuit type Integrated free running circuit in the output chip Overcurrent shutdown 0.7 A, minimum Maximum output current when switched off 10 µA When not loaded, a voltage can be measured even at an output that is not set. Typical Power Dissipation With 24 V Supply Voltage Formula to Calculate the Power Dissipation of the Electronics n 2 PTOT = 1.68 W + S (0.11 W + ILi x 0.28 W) i=1 7119_en_02 Where PTOT i n ILi Total power dissipation of the module Continuous index Number of set outputs (n = 1 to 16) Load current of output i PHOENIX CONTACT 5 ILB IB 24 DO16-DSUB Limitation of Simultaneity, Derating Ambient Temperature (TA) Maximum Load Current (I) at 100% Simultaneity Maximum Load Current (I) at 50% Simultaneity -25°C to +45°C 16 x 0.5 A 8 x 0.5 A +46°C to +60°C Itot = 8 A - ((TA - 45°C) x 0.267 A/°C) 8 x 0.5 A With an ambient operating temperature of up to 45°C and 100% simultaneity, a load current of 0.5 A per channel is permissible. If all four channels are used at a temperature of > 45°C, the permissible working point must be defined according to the above formula. An example can be found in the "Configuring and Installing the INTERBUS Inline Product Range" user manual IB IL SYS PRO UM E. I [A ] 8 4 -2 5 0 4 5 6 0 T A [° C ] 6 8 9 1 A 0 1 2 Approvals For the latest approvals, please visit www.download.phoenixcontact.com. 7119_en_02 PHOENIX CONTACT 6 ILB IB 24 DO16-DSUB Internal Circuit Diagram U L B A R C Local Diagnostic and Status Indicators R D O U T B U S E 1 8 x 8 x 1 3 B A O 1 R C O P C 2 3 4 E 1 2 U L O 2 4 1 2 3 O 3 2 3 4 O 4 4 R D 5 V 2 4 V U U U A 1 D O 1 ...8 A 2 D O 9 ...1 6 L U A 1 U A 2 U L P W R U L U A 1 U A 2 IN T E R B U S Figure 3 7 1 1 9 A 0 0 5 Diagnostic and status indicators of the ILB IB 24 DO16-DSUB module 7 1 1 9 B 0 0 2 Figure 2 Internal wiring of the terminal points Designation Color Meaning UL Green Communications power RC Green Remote bus cable check BA Green Bus active RD Yellow Outgoing remote bus disabled UA1 Green Actuator supply 1 (connector 5 and connector 6 for actuators) UA2 Green Actuator supply 2 (connector 7 and connector 8 for actuators) E Red Short circuit or overload at one of the outputs 1 to 4 Yellow Status indicators of the outputs BUS Key: LED OPC Protocol chip (bus logic) PWR x x x Power supply unit with electrical isolation X X X Optocoupler Short-circuit-proof output OUT If the error LED (E) of a group of eight outputs lights up (e.g., connector 5 and connector 6), this indicates that a short circuit or overload is present at one or more of the outputs in this group. 7119_en_02 PHOENIX CONTACT 7 ILB IB 24 DO16-DSUB Connecting INTERBUS, the Supply, and Actuators 1 .1 1 .2 1 . X 1 U L U A 1U A 2N C 1 .3 X 2 1 1 .4 0 V 0 V 0 V N C F E 1 2 1 .1 2 .1 1 .2 2 .2 1 .3 2 .3 1 .4 2 .4 1 .5 2 .5 1 .5 1 .6 2 .1 2 .2 2 .3 2 .4 2 .5 1 .6 2 .6 2 .6 5 -8 R E M O T E O U T R E M O T E IN IL B IB 2 4 D O 1 6 -D S U B d e r -N o .: 2 8 7 8 5 X 3 X 4 7 1 1 9 C 0 0 6 Figure 4 Terminal point assignment of the connectors Terminal Point Assignment of the MINI COMBICON Connectors for the Connection of the Supply Voltages (Connectors X1 and X2 in Figure 4 on page 8) Terminal Point UL UA1 UA2 NC Terminal Point 0V 0V 0V NC FE Assignment 24 V communications power UL 24 V actuator supply UA1 24 V actuator supply UA2 Not used Assignment GND GND GND Not used Functional earth ground The terminal points for GND (0V) can have a total current of 8 A per terminal point. The maximum current carrying capacity of 8 A must not be exceeded. If the total output current in your application is > 8 A, the module is to be supplied via a minimum of two GND terminal points (0V). The supply points have the same ground potential. All ground supplies on a module are electrically connected with one another. The communications power is also electrically connected via all contacts. In this way it can supply all potentials with just one supply without the need for additional terminals, see "Connection example" on page 10. 7119_en_02 PHOENIX CONTACT 8 ILB IB 24 DO16-DSUB Terminal Point Assignment of the INTERBUS Connectors (Connectors X 3 and X4 in Figure 4 on page 8) 6 1 7 1 6 2 8 5 9 re 3 9 4 5 n o re re A B D O D O D I D I s e rv e G N D t c o n s e rv e s e rv e D O D O D I D I s e rv G N D t c o s e rv s e rv re d n o re re n . d d 6 1 7 2 3 n n . e d e d 1 6 8 e d 9 5 9 4 5 7 1 1 7 B 0 1 2 Figure 5 A B Assignment of the remote bus interfaces (DSUB connector) Remote OUT (outgoing remote bus) Remote IN (incoming remote bus) Assignment Remark/Wire Color in the INTERBUS Standard Cable Receive Green DO DO Receive Yellow Transmit Pink DI DI Transmit Gray GND Reference potential Brown Shield Shield potential is connected with a (incoming capacitor to functional earth ground remote bus) (FE) of the potential jumper. Shield Shield potential is directly connected (outgoing to functional earth ground (FE) of the remote bus) potential jumper. In order to assemble the connectors, proceed as described in the IBS SYS PRO INST UM E user manual. Terminal Point Assignment of the Output Connectors (Connectors 5 to 8 in Figure 4 on page 8) Terminal Point Assignment Connector 5 (O1) Connector 6 (O2) Connector 7 (O3) Connector 8 (O4) 1.1, 2.1 1.1, 2.1 1.1, 2.1 1.1, 2.1 Signal output (OUT) 1.2, 2.2 1.2, 2.2 1.2, 2.2 1.2, 2.2 Ground contact (GND) for 2 and 3-wire termination 1.3, 2.3 1.3, 2.3 1.3, 2.3 1.3, 2.3 FE connection for 3-wire termination 1.4, 2.4 1.4, 2.4 1.4, 2.4 1.4, 2.4 Signal output (OUT) 1.5, 2.5 1.5, 2.5 1.5, 2.5 1.5, 2.5 Ground contact (GND) for 2 and 3-wire termination 1.6, 2.6 1.6, 2.6 1.6, 2.6 1.6, 2.6 FE connection for 3-wire termination 7119_en_02 PHOENIX CONTACT 9 ILB IB 24 DO16-DSUB Connection Example U A 1 + F E U 7 8 + A 2 O U T 6 U 6 O U T 1 6 5 L 7 1 1 9 A 0 1 0 Figure 6 Connection example The numbers above the module illustration identify the connector slots. When connecting the actuators observe the assignment of the terminal points to the process data (see "Process Data" on page 11). The module has an FE spring (metal clip) on the bottom of the electronics base. This spring creates an electrical connection to the DIN rail. Use grounding terminals to connect the DIN rail to protective earth ground. The module is grounded when it is snapped onto the DIN rail. To ensure reliable functional earth grounding of the module even when the DIN rail is dirty or the metal clip is damaged, Phoenix Contact also recommends grounding the module via one of the FE terminal points. 7119_en_02 PHOENIX CONTACT 10 ILB IB 24 DO16-DSUB Programming Data ID code 01hex (01dec) Length code 01hex Process data channel 16 bits Input address area 0 words Output address area 1 word Parameter channel (PCP) 0 words Register length (bus) 1 word Process Data For the assignment of the illustrated (byte.bit) view to your control or computer system, please refer to the DB GB IBS SYS ADDRESS data sheet. Please refer to the application note for addressing 16-channel ILB modules. The documentation can be downloaded at www.download.phoenixcontact.com. Assignment of the Terminal Points to the OUT Process Data Word (Slots 5 to 8) (Word.bit) view Word Bit (Byte.bit) view Byte Bit Module Slot Terminal point (signal) Terminal point (GND) Terminal point FE Status indicator Slot LED 15 7 14 13 12 11 Byte 0 4 3 10 9 Word 0 8 7 6 5 4 3 Byte 1 4 3 2 1 0 6 5 2 1 0 7 6 5 2 1 0 6 (O2) 5 (O1) 8 (O4) 7 (O3) 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.4 1.4 2.1 1.1 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.5 1.5 2.2 1.2 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 2.6 1.6 2.3 1.3 6 5 8 7 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 Diagnostics Error Table With Diagnostic Data and Status Indicators Error Type Actuator supply UA1 or UA2 too low Short circuit of a digital output Diagnostic Data No response I/O error message Status indicators UA1 and UA2 LEDs are off LED E of the affected output group is red © PHOENIX CONTACT 03/2007 7119_en_02 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00 www.phoenixcontact.com 11