2900351

https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) PLC-INTERFACE for railway applications, consisting of basic terminal block with push-in connection and plug-in miniature relay with multi-layer gold contact, range: 0.7 x UN to 1.25 x UN, temperature class TX: -40°C to +70°C, 2 PDTs, input voltage 110 V DC The figure shows a version with a screw connection Product Features  Optimum relay operation thanks to wide-range electronics  Vibration and shock resistance according to EN 50155  Safe isolation according to DIN EN 50178 between coil and contact  Certified according to EN 50155  Spring-cage and Push-in connection technology  Temperature range from -40°C to +70°C (+85°C briefly)  Input voltage range of 0.7 to 1.25 x UN (1.4 x UN briefly)     Key commercial data Packing unit 1 pc Weight per Piece (excluding packing) 99.99 GRM Custom tariff number 85364900 Country of origin Germany Technical data Note Utilization restriction EMC: class A product, see manufacturer's declaration in the download area Dimensions Width 14 mm Height 80 mm 10/28/2014   Page 1 / 6 https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Technical data Dimensions Depth 94 mm Ambient conditions Ambient temperature (operation) -40 °C ... 70 °C (Temperature class TX) Ambient temperature (storage/transport) -40 °C ... 85 °C Coil side Nominal input voltage UN 110 V DC Input voltage range in reference to UN 0.7 ... 1.25 Typical input current at UN 4.5 mA Typical response time 5 ms Typical release time 11 ms Operating voltage display Yellow LED Protective circuit Bridge rectifier Bridge rectifier Free-wheeling diode Damping diode Surge protection RCZ filter Wide-range electronics Contact side Contact type 2 PDT Contact material AgNi, hard gold-plated Maximum switching voltage 30 V AC 36 V DC Minimum switching voltage 100 mV (at 10 mA) Maximum inrush current 50 mA Min. switching current 1 mA (at 24 V) Limiting continuous current 50 mA Interrupting rating (ohmic load) max. 1.2 W (at 24 V DC) Note the following values are applicable if a gold layer is destroyed Maximum switching voltage 250 V AC/DC (Separating plate PLC-ATP must be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules.) Minimum switching voltage 12 V AC/DC Limiting continuous current 2x 6 A (see derating curve) Maximum inrush current 15 A (300 ms) Min. switching current 10 mA Interrupting rating (ohmic load) max. 140 W (at 24 V DC) 100 W (at 48 V DC) 10/28/2014   Page 2 / 6 https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Technical data Contact side 60 W (at 60 V DC) 44 W (at 110 V DC) 60 W (at 220 V DC) 1500 VA (for 250 V AC) Switching capacity in acc. with DIN VDE 0660/IEC 60947 2 A (at 24 V, DC13) 0.2 A (at 110 V, DC13) 0.2 A (at 250 V, DC13) 2 A (at 24 V, AC15) 2 A (at 120 V, AC15) 2 A (at 250 V, AC15) General Test voltage relay winding/relay contact 5 kVrms (50 Hz, 1 min.) Test voltage PDT/PDT 2.5 kVrms (50 Hz, 1 min.) Operating mode 100% operating factor Degree of protection Relay socket RT III (Relay) Mechanical service life Approx. 3 x 10 cycles Inflammability class according to UL 94 V0 Standards/regulations EN 50155 (VDE 0115 part 200) 7 EN 50178 IEC 62103 EN 61373 EN 50121 Rated surge voltage / insulation 6 kV / Basic isolation Rated insulation voltage 250 V AC Pollution degree 2 Surge voltage category III Mounting position any Assembly instructions In rows with zero spacing Connection data Connection method Push-in connection Stripping length 8 mm Conductor cross section stranded min. 0.14 mm² Conductor cross section stranded max. 2.5 mm² Conductor cross section solid min. 0.14 mm² Conductor cross section solid max. 2.5 mm² 10/28/2014   Page 3 / 6 https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Technical data Connection data Conductor cross section AWG/kcmil max 14 Conductor cross section AWG/kcmil min. 26 Classifications eCl@ss eCl@ss 4.0 27371001 eCl@ss 4.1 27371001 eCl@ss 5.0 27371001 eCl@ss 5.1 27371001 eCl@ss 6.0 27371001 eCl@ss 7.0 27371001 eCl@ss 8.0 27371001 ETIM ETIM 4.0 EC000196 ETIM 5.0 EC000196 UNSPSC UNSPSC 6.01 30211916 UNSPSC 7.0901 39121515 UNSPSC 11 39121515 UNSPSC 12.01 39121515 UNSPSC 13.2 39121515 Approvals Approvals Approvals UL Listed / cUL Listed / UL Recognized / cUL Recognized / GL / cULus Recognized / cULus Listed Ex Approvals Approvals submitted 10/28/2014   Page 4 / 6 https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Approvals Approval details UL Listed  cUL Listed  UL Recognized  cUL Recognized  GL  cULus Recognized  cULus Listed  Drawings 10/28/2014   Page 5 / 6 https://www.phoenixcontact.com/us/products/2900351 Relay Module - PLC-RPT-110UC/21-21AU/RW - 2900351 Diagram Diagram 10 7 10 6 10 6 4 Cycles Switching current [A] 20 1 2 4 1 3 2 1 105 2 0,5 0,3 0,2 104 0,1 10 1 2 3 4 20 30 50 70 100 200 Switching voltage [V] 0 300 1 2 3 4 5 6 7 8 9 Switching current [A] 10 1 250 V AC, ohmic load (DC coils) 2 250 V AC, ohmic load (AC coils) AC, ohmic load DC, ohmic load, contacts in series DC, ohmic load DC, L/R = 40 ms Electrical service life Interrupting rating Circuit diagram 21 24 A2 11 A1 14 22 12 Phoenix Contact 2014 © - all rights reserved http://www.phoenixcontact.com 10/28/2014   Page 6 / 6