2903330

https://www.phoenixcontact.com/us/products/2903330 Relay Module - RIF-1-RPT-LDP-24DC/2X21AU - 2903330 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://download.phoenixcontact.com) Pre-assembled relay module with push-in connection, consisting of: relay base, multi-layer contact relay, plug-in display/suppressor module, and retaining bracket. Contact type: 2 PDTs. Input voltage: 24 V DC Key commercial data Packing unit 1 pc Weight per Piece (excluding packing) 68.0 GRM Custom tariff number 85364110 Country of origin Germany Technical data Dimensions Width 16 mm Height 93 mm Depth 75 mm Ambient conditions Ambient temperature (operation) -40 °C ... 70 °C Ambient temperature (storage/transport) -40 °C ... 85 °C Coil side Nominal input voltage UN 24 V DC Input voltage range in reference to UN (see diagram) Nominal input current at UIN 18 mA Typical response time 8 ms Typical release time 10 ms Operating voltage display Yellow LED Protective circuit Damping diode Polarity protection diode 3/7/14   Page 1 / 6 https://www.phoenixcontact.com/us/products/2903330 Relay Module - RIF-1-RPT-LDP-24DC/2X21AU - 2903330 Technical data Contact side Contact type 2 PDT Contact material AgNi, hard gold-plated Maximum switching voltage 30 V AC 36 V DC Minimum switching voltage 100 mV (at 10 mA) Maximum inrush current 50 mA Min. switching current 1 mA (at 24 V) Limiting continuous current 50 mA Interrupting rating (ohmic load) max. 1.2 W (at 24 V DC) Switching capacity in acc. with DIN VDE 0660/IEC 60947 2 A (24 V (DC13)) 3 A (230 V (AC 15)) Note the following values are applicable if a gold layer is destroyed Maximum switching voltage 250 V AC/DC Minimum switching voltage 5 V (at 10 mA) Limiting continuous current 25 A (20 ms, N/O contact) Min. switching current 10 mA (At 5 V) Interrupting rating (ohmic load) max. 192 W (at 24 V DC) 96 W (at 48 V DC) 60 W (at 60 V DC) 44 W (at 110 V DC) 57 W (at 220 V DC) 2000 VA (for 250 V AC) Connection data Connection method Push-in connection Conductor cross section solid min. 0.14 mm² Conductor cross section solid max. 1.5 mm² Conductor cross section stranded min. 0.14 mm² Conductor cross section stranded max. 1.5 mm² Conductor cross section stranded, with ferrule with plastic sleeve min. 0.14 mm² Conductor cross section stranded, with ferrule with plastic sleeve max. 1.5 mm² Conductor cross section stranded, with ferrule without plastic sleeve min. 0.14 mm² Conductor cross section stranded, with ferrule without plastic sleeve max. 1.5 mm² Conductor cross section AWG/kcmil min. 26 Conductor cross section AWG/kcmil max 16 Stripping length 8 mm General 3/7/14   Page 2 / 6 https://www.phoenixcontact.com/us/products/2903330 Relay Module - RIF-1-RPT-LDP-24DC/2X21AU - 2903330 Technical data General Type of note Notes on operation Note FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21) Test voltage relay winding/relay contact 4 kVrms (50 Hz, 1 min.) Test voltage PDT/PDT 2.5 kVrms (50 Hz, 1 min.) Operating mode 100% operating factor Degree of protection IP20 (Relay socket) RT III (Relay) Mechanical service life Approx. 3 x 10 cycles Standards/regulations DIN EN 50178 7 IEC 62103 Pollution degree 2 Surge voltage category III Mounting position any Assembly instructions In rows with zero spacing Articles in set Relay socket - RIF-1-BPT/2X21 - 2900931 RIF-1... relay base, for miniature power relay with 1 or 2 PDTs or solid-state relays of the same design, push-in connection, plug-in option for input/suppressor modules, for mounting on NS 35/7,5     Single relay - REL-MR- 24DC/21-21AU - 2961215 Pluggable miniature relays, with multi-layer contact, 2 PDT, input voltage 24 V DC     3/7/14   Page 3 / 6 https://www.phoenixcontact.com/us/products/2903330 Relay Module - RIF-1-RPT-LDP-24DC/2X21AU - 2903330 Articles in set Plug-in module - RIF-LDP-12-24 DC - 2900939 Plug-in module, for mounting on RIF-1, RIF-2, RIF-3, and RIF-4, with freewheeling diode and yellow LED, polarity: A1+, A2-, input voltage: 12 - 24 V DC ±20%     Retaining bracket - RIF-RH-1 - 2900953 Relay retaining bracket, with ejector function and holder for marking material, suitable for RIF-1 relay base, for 16 mm tall miniature power relay and solid-state relay     Classifications eCl@ss eCl@ss 4.0 27371102 eCl@ss 4.1 27371102 eCl@ss 5.0 27371603 eCl@ss 5.1 27371603 eCl@ss 6.0 27371603 eCl@ss 7.0 27371603 eCl@ss 8.0 27371603 ETIM ETIM 3.0 EC001456 ETIM 4.0 EC001456 ETIM 5.0 EC001437 UNSPSC UNSPSC 6.01 30211917 UNSPSC 7.0901 39121516 UNSPSC 11 39121516 UNSPSC 12.01 39121516 UNSPSC 13.2 39121516 Drawings 3/7/14   Page 4 / 6 https://www.phoenixcontact.com/us/products/2903330 Relay Module - RIF-1-RPT-LDP-24DC/2X21AU - 2903330 22 12 24 14 21 11 Diagram Coil voltage U/UN Circuit diagram A1+ A2- DC coils 1,8 1,7 1,6 1,5 1,4 1,3 1,2 1,1 1,0 0,9 0,8 0,7 0,6 20 30 40 50 60 70 Ambient temperature [°C] 80 DC coils AC coils Operating voltage range Diagram Diagram 11 10 10 6 4 9 2 1 0,5 0,3 0,2 0,1 10 20 30 50 70 100 200 Switching voltage [V] AC, ohmic load DC, ohmic load DC, L/R = 40 ms 10 7 10 6 300 Limiting continuous current per contact [A] Switching current [A] 20 8 7 6 5 4 3 2 1 20 30 40 50 60 70 Ambient temperature [°C] 80 DC coil AC coil Interrupting rating Contact derating Diagram Diagram Reduction factor Cycles 1 0,9 1 10 10 5 2 0,8 0,7 0,6 0,5 0,4 4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Switching current [A] 0,3 1 0,9 0,8 0,7 0,6 0,5 0,4 0,3 0,2 COS j 1 250 V AC, ohmic load (DC coils) 2 250 V AC, ohmic load (AC coils) Electrical service life Service life reduction factor 3/7/14   Page 5 / 6 https://www.phoenixcontact.com/us/products/2903330 © Phoenix Contact 2013 - all rights reserved http://www.phoenixcontact.com 3/7/14   Page 6 / 6