QUINT4-PS/1AC/24DC/40
Power supply unit
Data sheet
108827_en_00
1
© PHOENIX CONTACT 2019-11-11
Description
QUINT POWER power supplies with SFB Technology and
preventive function monitoring ensure superior system
availability.
Technical data (short form)
Input voltage range
100 V AC ... 240 V AC
-15 % ... +10 %
Powerful
Mains buffering
typ. 29 ms (120 V AC)
typ. 32 ms (230 V AC)
–
–
Nominal output voltage (UN)
24 V DC
Setting range of the output voltage
(USet)
24 V DC ... 29.5 V DC
Nominal output current (IN)
Static Boost (IStat.Boost)
Dynamic Boost (IDyn.Boost)
Selective Fuse Breaking (ISFB)
40 A
45 A
60 A (5 s)
215 A (15 ms)
Output power (PN)
Output power (PStat. Boost)
Output power (PDyn. Boost)
960 W
1080 W
1440 W
Efficiency
typ. 94.8 % (120 V AC)
typ. 95.9 % (230 V AC)
Residual ripple
< 50 mVPP
SFB Technology: 6 times the nominal current for 15 ms
Power reserves:
Static boost of up to 125% (PN) for a sustained period
Dynamic boost of up to 200% (PN) for 5 s
Robust
–
–
Mains buffering ≥ 20 ms
High degree of electrical immunity, thanks to integrated
gas discharge tube (6 kV)
Preventive
–
Comprehensive signaling:
Analog signal, digital signal, relay contact, LED bar
graph
Can be ordered pre-configured
–
MTBF (IEC 61709, SN 29500)
> 555000 h (40 °C)
Ambient temperature (operation)
-25 °C ... 70 °C
-40°C (startup type tested)
> 60 °C Derating: 2.5 %/K
Dimensions W/H/D
120 mm / 130 mm / 140 mm
Weight
2.6 kg
Perform configuration online and order 1 or more units
All technical specifications are nominal values and refer to a room temperature of 25 °C and 70 % relative
humidity at 100 m above sea level.
QUINT4-PS/1AC/24DC/40
2
Table of contents
1
Description .............................................................................................................................. 1
2
Table of contents ..................................................................................................................... 2
3
Ordering data .......................................................................................................................... 3
4
Technical data ......................................................................................................................... 5
5
Safety and installation notes .................................................................................................. 16
6
High-voltage test (HIPOT) ..................................................................................................... 17
7
Structure of the power supply ................................................................................................ 19
8
Mounting/removing the power supply .................................................................................... 22
9
Device connection terminal blocks ........................................................................................ 25
10
Output characteristic curves .................................................................................................. 27
11
Configuring the power supply ................................................................................................ 29
12
Boost currents ....................................................................................................................... 31
13
SFB Technology .................................................................................................................... 32
14
Signaling................................................................................................................................ 37
15
Operating modes ................................................................................................................... 45
16
Derating................................................................................................................................. 47
108827_en_00
PHOENIX CONTACT
2 / 50
QUINT4-PS/1AC/24DC/40
3
Ordering data
Description
Type
Primary-switched QUINT POWER power supply with free QUINT4-PS/1AC/24DC/40
choice of output characteristic curve, SFB (selective fuse
breaking) technology, and NFC interface, input: 1phase, output: 24 V DC/40 A
Order No.
Pcs./Pkt.
2904603
1
Versions of the primary-switched QUINT POWER power supply with SFB Technology (selective fuse
breaking), which are configured online, can now be ordered in batches of one or more using the following web
code: phoenixcontact.net/webcode/#0852
Accessories
Type
Order No.
Pcs./Pkt.
Universal wall adapter for securely mounting the device in UWA 182/52
the event of strong vibrations. The device is screwed
directly onto the mounting surface. The universal wall
adapter is attached on the top/bottom.
2938235
1
2-piece universal wall adapter for securely mounting the
device in the event of strong vibrations. The profiles that
are screwed onto the side of the device are screwed
directly onto the mounting surface. The universal wall
adapter is attached on the left/right.
UWA 130
2901664
1
Assembly adapter for QUINT-PS... power supply on S7300 rail
QUINT-PS-ADAPTERS7/1
2938196
1
Near Field Communication (NFC) programming adapter
with USB interface for the wireless configuration of NFCcapable products from PHOENIX CONTACT with
software. No separate USB driver is required.
TWN4 MIFARE NFC USB
ADAPTER
2909681
1
Type 2/3 surge protection, consisting of protective plug
and base element with screw connection. For singlephase power supply network with integrated status
indicator and remote signaling. Nominal voltage
230 V AC/DC.
PLT-SEC-T3-230-FM-UT
2907919
5
End clamp, width: 10 mm, height: 44 mm,
material: Aluminum, length: 59 mm, color: silver
E/AL-NS 35
1201662
10
Type 3 surge protection, consisting of protective plug and PLT-SEC-T3-24-FM-UT
base element, with integrated status indicator and remote
signaling for single-phase power supply networks.
Nominal voltage 24 V AC/DC.
2907916
5
Type 2/3 surge protection, consisting of protective plug
and base element with Push-in connection. For singlephase power supply network with integrated status
indicator and remote signaling. Nominal voltage
230 V AC/DC.
2907928
5
2907925
5
PLT-SEC-T3-230-FM-PT
Type 3 surge protection, consisting of protective plug and PLT-SEC-T3-24-FM-PT
base element, with integrated status indicator and remote
signaling for single-phase power supply networks.
Nominal voltage 24 V AC/DC.
108827_en_00
PHOENIX CONTACT
3 / 50
QUINT4-PS/1AC/24DC/40
Accessories
Type
Order No.
Pcs./Pkt.
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBMC E4 24DC/1-4A NO
2906031
1
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBMC E4 24DC/1-10A NO
2906032
1
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBMC E4 24DC/1-4A+ IOL
2910410
1
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBMC E4 24DC/1-10A IOL
2910411
1
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBM E4 24DC/0.5-10A NO-R 2905743
1
Electronic device circuit breaker, number of positions: 1,
mounting type: DIN rail: 35 mm, Color: light grey
RAL 7035
CBM E8 24DC/0.5-10A NO-R 2905744
1
The range of accessories is being continuously extended. The current range of accessories can be found in
the download area for the product.
108827_en_00
PHOENIX CONTACT
4 / 50
QUINT4-PS/1AC/24DC/40
4
Technical data
Input data
Unless otherwise stated, all data applies for 25°C ambient temperature, 230 V AC input voltage, and nominal
output current (IN).
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
110 V DC ... 250 V DC -18 % ... +40 %
Electric strength, max.
300 V AC 60 s
Frequency range (fN)
50 Hz ... 60 Hz -10 % ... +10 %
Frequency (fR) for railway power supply systems
16.7 Hz (acc. to EN 50163)
Railway power supply systems can be operated at 16.7 Hz. Use conditions and technical data on request.
Current draw typ.
13.6 A (100 V AC)
10 A (120 V AC)
5.2 A (230 V AC)
5.4 A (240 V AC)
12 A (110 V DC)
5 A (250 V DC)
The specified values for current consumption apply for operation in the static boost (PN x 125%).
Discharge current to PE
typical
< 3.5 mA
1.7 mA (264 V AC, 60 Hz)
Mains buffering
typ. 29 ms (120 V AC)
typ. 32 ms (230 V AC)
Inrush current limitation after 1 ms
Inrush current integral
(I2t)
Input fuse slow-blow, internal
12 A
< 1 A2s
16 A
During the first few microseconds, the current flow into the filter capacitors is excluded.
The SCCR value (short-circuit current rating) of the power supply unit corresponds to the SCCR value of the
backup fuse (see input protection table).
The external backup fuse must be approved for the (AC) supply voltage used and the voltage level.
108827_en_00
PHOENIX CONTACT
5 / 50
QUINT4-PS/1AC/24DC/40
Input protection , AC/DC ( to be connected externally upstream )
Input current IIn
Input protection
Circuit breaker
Neozed fuse
or equivalent
Power switch
≤ 13 x IIn
(maximum magnetic tripping)
Characteristics
A
B
C
D
K
gG
4A
-
-
-
-
-
-
6A
-
-
-
-
-
-
8A
-
10 A
-
13 A
16 A
Electric strength of the insulation
Housing
Input
Signaling
(+)
L
N
(-)
B
B
A
D
Output
PE
+
C
Type test (IEC/EN 60950-1)
Production test
A
B
C
D
2.5 kV AC
4 kV AC
0.5 kV DC
0.5 kV DC
2 kV AC
2 kV AC
0.5 kV DC
0.5 kV DC
Field test (with gas-filled surge arrester)
0.8 kV AC
1.1 kV DC
0.8 kV AC
1.1 kV DC
0.5 kV DC
0.5 kV DC
Field test (gas-filled surge arrester de-contacted)
2 kV AC
2.83 kV DC
2 kV AC
2.83 kV DC
0.5 kV DC
0.5 kV DC
Power Factor
POWER factor
1,0
0,9
0,8
0,7
= UIn: 120 V AC/UOut: 24 V DC
= UIn: 230 V AC/UOut: 24 V DC
0,6
0,5
5
10
15
20
25
30
35
40
45
50
55
60
IOut [A]
108827_en_00
PHOENIX CONTACT
6 / 50
QUINT4-PS/1AC/24DC/40
Crest factor
120 V AC
230 V AC
typ. 1.5
typ. 1,6
IIn [A]
Input current vs. output current
14,0
12,0
10,0
8,0
6,0
4,0
= UIn: 120 V AC/UOut: 24 V DC
= UIn: 230 V AC/UOut: 24 V DC
2,0
0,0
0
10
20
30
40
50
60
IOut [A]
Input connection data
Connection method
Screw connection
Conductor cross section, solid
0.2 mm² ... 6 mm²
Conductor cross section, flexible
0.2 mm² ... 4 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.25 mm² ... 4 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.25 mm² ... 4 mm²
Conductor cross section AWG
24 ... 10
Stripping length
8 mm
Tightening torque
0.5 Nm ... 0.6 Nm
Output data
Nominal output voltage (UN)
24 V DC
Setting range of the output voltage (USet) ( constant
capacity )
24 V DC ... 29.5 V DC
Nominal output current (IN)
40 A
Static Boost (IStat.Boost)
45 A
Dynamic Boost (IDyn.Boost)
60 A (5 s)
Selective Fuse Breaking (ISFB)
215 A (15 ms)
Magnetic circuit breaker tripping
A1...A40 / B2...B25 / C1...C13 / Z1...Z16
Control deviation Static load change 10 % ... 90 %
< 0.5 %
Control deviation Dynamic load change 10 % ... 90 %, (10 < 1 %
Hz)
Control deviation change in input voltage ±10 %
< 0.25 %
Short-circuit-proof
yes
No-load proof
yes
Residual ripple ( with nominal values )
< 50 mVPP
Connection in parallel
Yes, for redundancy and increased capacity
Connection in series
yes
Feedback voltage resistance
≤ 35 V DC
Protection against overvoltage at the output (OVP)
≤ 32 V DC
108827_en_00
PHOENIX CONTACT
7 / 50
QUINT4-PS/1AC/24DC/40
Output connection data
Connection method
Screw connection
Conductor cross section, solid
0.5 mm² ... 16 mm²
Conductor cross section, flexible
0.5 mm² ... 16 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.5 mm² ... 16 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.5 mm² ... 16 mm²
Conductor cross section AWG
20 ... 6
Stripping length
10 mm
Tightening torque
1.2 Nm ... 1.5 Nm
LED signaling
POut > 100%
LED lights up yellow, output power > 960 W
POut > 75%
LED lights up green, output power > 720 W
POut > 50%
LED lights up green, output power > 480 W
UOut > 0.9 x USet
LED lights up green
UOut < 0.9 x USet
LED flashes green
Signal contact (configurable)
Signal output (configurable) Out 1
Digital
0 / 24 V DC , 20 mA
Default
24 V DC , 20 mA ( 24 V DC for UOut > 0.9 x USet )
Signal output (configurable) Out 2
Digital
0 / 24 V DC , 20 mA
Analog
4 mA ... 20 mA 5 % (Load ≤400 )
Default
24 V DC , 20 mA ( 24 V DC for POut 0.9 USet)
Maximum contact load
24 V DC 1 A , 30 V AC/DC 0.5 A
Control input (configurable) Rem
Function
Output power ON/OFF (SLEEP MODE)
Default
Output power ON (>40 kΩ/24 V DC/open bridge between Rem
and SGnd)
Signal ground SGnd
Reference potential for Out1, Out2, and Rem
108827_en_00
PHOENIX CONTACT
8 / 50
QUINT4-PS/1AC/24DC/40
Signal connection data
Connection method
Push-in connection
Conductor cross section, solid
0.2 mm² ... 1 mm²
Conductor cross section, flexible
0.2 mm² ... 1.5 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.2 mm² ... 0.75 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.2 mm² ... 1.5 mm²
Conductor cross section AWG
24 ... 16
Stripping length
8 mm
Reliability
230 V AC
MTBF (IEC 61709, SN 29500)
> 934000 h (25 °C)
> 555000 h (40 °C)
> 249000 h (60 °C)
Life expectancy (electrolytic capacitors)
Output current (IOut)
120 V AC
230 V AC
20 A
> 394000 h ( 40 °C )
> 452000 h ( 40 °C )
40 A
> 113000 h ( 40 °C )
> 149000 h ( 40 °C )
40 A
> 320000 h ( 25 °C )
> 422000 h ( 25 °C )
The expected service life is based on the capacitors used. If the capacitor specification is observed, the
specified data will be ensured until the end of the stated service life. For runtimes beyond this time, error-free
operation may be reduced. The specified service life of more than 15 years is simply a comparative value.
Switching frequency
Min.
Max.
PFC stage
50 kHz
500 kHz
Auxiliary converter stage
85 kHz
107 kHz
Main converter stage
45 kHz
200 kHz
General data
Degree of protection
IP20
Protection class
I
Inflammability class in acc. with UL 94 (housing / terminal V0
blocks)
Side element version
Aluminum
Hood version
Stainless steel X6Cr17
Dimensions W / H / D (state of delivery)
120 mm / 130 mm / 140 mm
Weight
2.6 kg
120 V AC
230 V AC
Maximum power dissipation in no-load condition
Power dissipation
100% Boost
> 75%
> 50% POut
DC OK
2
HV
/=
3
Input AC 100-240V
DC 110-250V
N/- L/+
1.1 1.2 1.3
In order to ensure permanent safe isolation of the AC input
circuit and DC output circuit, high-voltage testing is
performed as part of the safety approval process (type test)
and manufacturing (routine test).
6.2
2.2
4
Figure 1
Potential-related wiring for the high-voltage
test
Key
No. Designation
Color coding
1
2
3
Blue
Blue
--
Potential levels
Potential 1
Potential 2
--
Red
Potential 2
4
DC output circuit
Signal contacts
High-voltage
tester
AC input circuit
PHOENIX CONTACT
17 / 50
QUINT4-PS/1AC/24DC/40
6.3.2
Disconnecting the gas discharge tube
The built-in gas discharge tube inside the device ensures
that the power supply is effectively protected against
asymmetrical disturbance variables (e.g., EN 61000-4-5).
QUINT POW
Each surge voltage test represents a very high load for the
power supply. Therefore avoid unnecessary loading or
damage to the power supply due to excessive test voltages.
If necessary, the gas discharge tube inside the device can
be disconnected in order to use higher test voltages.
Following successful completion of testing, please
reconnect the gas-discharge tube.
A
M3
x8
13
14
m
e
R d
n
SG 1
t
u
O 2
t
Ou
3.3
3.4
3.5
3.6
t
os
Bo
0% Pout
0
> 15%
> 70%
> 5 OK
DC
B
Figure 2
Disconnect gas discharge tube
To disconnect the gas discharge tube, proceed as follows:
1. Remove power from the unit.
2. Unscrew the Phillips head screw completely and keep
the gas discharge tube screw in a safe place. The gasdischarge tube is now disconnected and is no longer
functional.
3. Perform the surge voltage test on the power supply.
4. Following successful high-voltage testing, screw the
gas discharge tube screw fully back into the power
supply.
DANGER: Risk of electric shock or
damage to the power supply due to using
the wrong gas discharge tube screw
To connect the gas-filled surge arrester, only
use the gas-filled surge arrester screw that
was originally installed in the power supply.
108827_en_00
PHOENIX CONTACT
18 / 50
QUINT4-PS/1AC/24DC/40
7.2
Structure of the power supply
Device dimensions
The fanless convection-cooled power supply can be
snapped onto all DIN rails according to EN 60715.
QUINT POWER Ord.No.2904603
7.1
120
Function elements
65
1
2
2
+
2.2
+
2.3
2.4
2.5
Output DC 24V 40A
UOut
29,5V
13
14
Rem
SGnd
Out 1
Out 2
24V
Signal
3.1
3.2
3.3
3.4
3.5
3.6
Ord.No.2904603
> 100% Boost
> 75%
> 50% POut
DC OK
2.1
+
QUINT POWER
10
2.1
2.2
+
2.3
2.4
130
7
3
2.5
Output DC 24V 40A
UOut
29,5V
24V
13
14
Rem
SGnd
Out 1
Out 2
Signal
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75%
> 50% POut
DC OK
Input AC 100-240V
DC 110-250V
N/- L/+
1.1 1.2 1.3
4
Figure 4
Device dimensions (dimensions in mm)
9
146
Input AC 100-240V
DC 110-250V
N/- L/+
8
1.1
1.2
1.3
2
5
6
140
2
Operating and indication elements
80
Figure 3
130
7
45
Key
No.
1
2
3
4
5
6
7
8
9
10
Designation
DC output voltage connection terminal blocks
Accommodation for cable binders
Signaling connection terminal blocks
Status and diagnostics indicators
Position NFC interface (Near Field Communication)
QR code web link
AC input voltage connection terminal blocks
Gas discharge tube for surge protection (left side of
housing)
Universal DIN rail adapter (rear of housing)
Output voltage button (-) / (+)
108827_en_00
Figure 5
Device dimensions (dimensions in mm)
PHOENIX CONTACT
19 / 50
QUINT4-PS/1AC/24DC/40
7.3
Keep-out areas
Nominal output
capacity
a
0
5
< 50 %
≥ 50 %
Spacing [mm]
b
40
50
c
20
50
If adjacent components are active and the
nominal output power ≥ 50%, there must be
lateral spacing of 15 mm.
a
a
QUINT POWER Ord.No.2904603
b
120
2.1
+
2.2
+
2.3
2.4
2.5
Output DC 24V 40A
UOut
29,5V
130
13
14
Rem
SGnd
Out 1
Out 2
24V
Signal
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75%
> 50% POut
DC OK
Input AC 100-240V
DC 110-250V
N/1.2
L/+
1.3
c
1.1
Figure 6
108827_en_00
Device dimensions and minimum keep-out
areas (in mm)
PHOENIX CONTACT
20 / 50
QUINT4-PS/1AC/24DC/40
7.4
Block diagram
2.1
2.2
1.1
N/L/+
1.2
1.3
active
PFC
2.3
2.4
2.5
+
+
-
OVP
NFC
3.1
3.2
3.3
C
3.4
3.5
3.6
Figure 7
13
14
Rem
SGnd
Out 1
Out 2
Block diagram
Key
Symbol
Designation
Surge protection (gas discharge tube)
Symbol
Surge protection (varistor) with filter
OVP
Bridge rectifier
active
PFC
Additional regulatory protection against
surge voltage
Relay contact and signal contacts
Inrush current limitation
C
Designation
Optocoupler (electrically isolating)
Power factor correction (PFC)
NFC
Microcontroller
Passive NFC interface (Near Field Communication)
Switching transistor and main transmitter
(electrically isolating)
Output voltage button (-) / (+)
Secondary rectification and smoothing
Signal/display LEDs (POut, DC OK)
Filter
Auxiliary converter (electrically isolating)
108827_en_00
PHOENIX CONTACT
21 / 50
QUINT4-PS/1AC/24DC/40
8
Mounting/removing the power
supply
8.1
Mounting the power supply unit
D
Proceed as follows to mount the power supply:
1. In the normal mounting position the power supply is
mounted on the DIN rail from above. Make sure that the
universal DIN rail adapter is in the correct position
behind the DIN rail (A).
2. Then press the power supply down until the universal
DIN rail adapter audibly latches into place (B).
3. Check that the power supply is securely attached to the
DIN rail.
C
A
Figure 9
A
8.3
B
Removing the power supply from the DIN rail
Retrofitting the universal DIN rail adapter
For installation in horizontal terminal boxes it is possible to
mount the power supply at a 90° angle to the DIN rail.
No additional mounting material is required.
Click
Use the Torx screws provided to attach the
universal DIN rail adapter to the side of the
power supply.
B
8.3.1
Figure 8
8.2
Snapping the power supply onto the DIN rail
Removing the power supply unit
Proceed as follows to remove the power supply:
1. Take a suitable screwdriver and insert this into the lock
hole on the universal DIN rail adapter (A).
2. Release the lock by lifting the screwdriver (B).
3. Carefully swivel the power supply forward (C) so that
the lock slides back into the starting position.
4. Then separate the power supply from the DIN rail (D).
Disassembling the universal DIN rail adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
8
M3x
Figure 10
108827_en_00
M3x
8
Disassembling the universal DIN rail adapter
PHOENIX CONTACT
22 / 50
QUINT4-PS/1AC/24DC/40
8.3.2
Mounting the universal DIN rail adapter
To mount the universal DIN rail adapter on the left side of the
device, proceed as follows:
1. Position the universal DIN rail adapter on the left side of
the housing so that the mounting holes are congruent
with the hole pattern for the mounting holes.
2. Insert the Torx screws that were removed earlier into the
appropriate hole pattern on the universal DIN rail
adapter so that the necessary drill holes on the power
supply can be accessed.
3. Screw the universal DIN rail adapter onto the power
supply.
The maximum tightening torque of the Torx
screw (Torx® T10) is 0.7 Nm.
x8
M3
8.4.1
Mounting the UWA 182/52 universal wall
adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter in such a way that
the keyholes or oval tapers face up. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes on the power supply can be accessed.
6. Screw the universal wall adapter onto the power supply.
x8
M3
8
M3x
Figure 11
8.4
8
M3x
Mounting the universal DIN rail adapter
Retrofitting the universal wall adapter
The UWA 182/52 universal wall adapter (Order No.
2938235) or UWA 130 universal wall adapter (Order No.
2901664) is used to attach the power supply directly to the
mounting surface.
The use of universal wall adapters is recommended under
extreme ambient conditions, e.g., strong vibrations. Thanks
to the tight screw connection between the power supply and
the universal wall adapter or the actual mounting surface, an
extremely high level of mechanical stability is ensured.
Figure 12
Mounting the UWA 182/52 universal wall
adapter
The maximum tightening torque of the Torx
screw (Torx® T10) is 0.7 Nm.
Make sure you use suitable mounting material
when attaching to the mounting surface.
The power supply is attached to the UWA 182
or UWA 130 universal wall adapter by means
of the Torx screws of the universal DIN rail
adapter.
108827_en_00
PHOENIX CONTACT
23 / 50
QUINT4-PS/1AC/24DC/40
8.4.2
Mounting the UWA 130 2-piece universal wall
adapter
Fix connection wiring to the power supply
Two receptacles for the bundled attachment of the
connection wiring are integrated in the left and right housing
panel. Use cable binders to secure the connection wiring
(optional PKB 140X3,6 - Order No. 1005460).
Proceed as follows to secure the connection wiring:
– Wire the power supply with sufficient connection
reserve (input terminal blocks, output terminal blocks,
signal terminal blocks)
– Bundle and set up the connection wiring so that the
cooling grilles on the top and bottom of the housing are
covered as little as possible.
– Thread the cable binders into the necessary
receptacles for the cable binders.
QUINT POWER
Ord.No.29046xx
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes in the side flanges of the power supply
can be accessed.
6. Screw the two-piece universal wall adapter onto the
power supply.
8.5
8
M3x
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
na
l
3.1
>1
> 7 00%
> 55% Boo
st
0
D %
8
M3x
CO
K
3.2
3.3
3.4
3.5
3.6
Po
u
t
Figure 14
–
Secure the connection wiring with the cable binders.
Make sure that the connection wiring is attached safely
and securely without damaging the connection wiring.
Mounting the UWA 130 universal wall adapter
QUINT POWER
Ord.No.29046xx
Figure 13
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
na
l
3.1
>1
> 7 00%
> 55% Boo
st
D 0%
CO
K
3.2
3.3
3.4
3.5
3.6
Po
u
t
Figure 15
108827_en_00
Lay and align connection wiring
Secure connection wiring with cable binder
PHOENIX CONTACT
24 / 50
QUINT4-PS/1AC/24DC/40
–
–
Shorten the excess length of the cable ties.
Then check again that the connection wiring is properly
secured.
9
Device connection terminal blocks
The AC input and DC output terminal blocks on the front of
the power supply feature screw connection technology. The
signal level is wired without tools by means of Push-in
connection technology.
QUINT POWER
Ord.No.29046xx
For the necessary connection parameters for
the connection terminal blocks, refer to the
technical data section.
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
9.1
Input
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
The power supply is operated on single-phase AC systems
or two outer conductors of three-phase systems. The power
supply is connected on the primary side via the INPUT L/N/
connection terminal blocks.
na
>1
> 7 00%
> 55% Boo
l
3.1
3.2
3.3
3.4
s
DC0% P t
OK out
3.5
3.6
Figure 16
Shorten protruding ends of the cable binder
The power supply is approved for connection
to TN, TT, and IT power grids with a maximum
phase-to-phase voltage of 240 V AC.
NOTE: Mechanical damage to the connection
wiring caused by friction
In extreme ambient conditions, e.g., strong
vibrations, protect the connection wiring
against mechanical damage using additional
insulation material. The additional insulation
material for protecting the connection wiring is
limited to the area where the cable binders are
attached.
TN-S
TN-C
L
N
PE
N L
L
PEN
N L
+ −
+ −
L1
L2
L3
N
PE
N L
L1
L2
L3
PEN
N L
+ −
TT
+ −
iT
L
PEN
N L
L
N
N L
+ −
+ −
L1
L2
L3
L1
L2
L3
N
N L
Figure 17
108827_en_00
+ −
N L
+ −
Network types
PHOENIX CONTACT
25 / 50
QUINT4-PS/1AC/24DC/40
9.2
Protection of the primary side
9.3
Installation of the device must correspond to EN 60950-1
regulations. It must be possible to switch off the device using
a suitable disconnecting device outside the power supply.
The line protection on the primary side is suitable for this
(see technical data section).
DANGER: Hazardous voltage
An all-pos. fuse must be present for operation
on two outer conductors of a three-phase
system.
Output
By default, the power supply is pre-set to a nominal output
voltage of 24 V DC.
The output voltage is adjusted via the two arrow keys (-)
and (+) on the front of the power supply.
When you press the arrow key once briefly, the output
voltage is reduced (-) or increased (+) by 3 mV. When you
press the arrow key for longer, the voltage is adjusted in
100 mV increments.
9.4
Protection of the secondary side
The power supply is electronically short-circuit-proof and
no-load-proof. In the event of an error, the output voltage is
limited
Protection for AC supply
Input AC 100...240 V
L
If sufficiently long connecting cables are used,
fuse protection does not have to be provided
for each individual load.
L
N
PE
If each load is protected separately with its
own protective device, the selective shutdown
in the event of a fault enables the system to
remain operational.
N
PE
Figure 18
N/-
L/+
Pin assignment for AC supply voltage
Protection for DC supply
Input DC 110...250 V
+
+
-
-
PE
Figure 19
N/-
L/+
Pin assignment for DC supply voltage
DC applications require upstream installation of a fuse that
is permitted for the operating voltage.
108827_en_00
PHOENIX CONTACT
26 / 50
QUINT4-PS/1AC/24DC/40
10
Output characteristic curves
This section describes the various output characteristic curves together with their areas of application for customization to
your specific application. The U/I Advanced characteristic curve is set by default.
M
Application
Normal load
Your benefits
Reliable power supply
System extension
+
-
Loads with high inrush
Energy storage charging
current
A stable 24 V, even in the No over-dimensioned
power supply unit
event of a sustained
required
overload
Fast charging
Selective tripping of
fuses
Keeps temperatures
low in the event of
faults
Short circuit, non-fused
Parallel loads continue
working
Low thermal stress in
the even of faults
Enables configuration
without fuse
Characteristics
-
U/I Advanced
-
Smart HICCUP
-
FUSE MODE
Symbol
-
-
-
Designation
Suitable for the application
-
108827_en_00
Not suitable for the application
PHOENIX CONTACT
27 / 50
QUINT4-PS/1AC/24DC/40
U/I Advanced output characteristic curve
10.2
UOut [V]
The preset U/I Advanced output characteristic curve is
optimized for the following applications:
– For selective tripping of standard circuit breakers (SFB
technology). The power supply supplies up to 6 times
the nominal current for 15 ms. Loads connected in
parallel continue working.
– When supplying loads with high switch-on currents,
such as motors. The dynamic boost of the power supply
supplies up to 200% of the nominal power for 5 s. This
ensures that sufficient reserve energy is available;
overdimensioning of the power supply is not necessary.
– For system extension. With the static boost, up to
125% of the nominal output power is available for a
sustained period (up to 40°C).
– For fast energy storage charging (e.g., of batteries) to
supply a wide range of loads. The power supply
operates in the nominal operating range. Energy supply
to the load is ensured.
UN
Smart HICCUP output characteristic curve
The SMART HICCUP output characteristic curve keeps the
thermal load of the connecting cables at a low level in the
event of a sustained overload. If loads are not protected or
are protected in a way that is not permitted, the loads are
supplied for 2 s. The DC output of the power supply is then
switched off for 8 s. This procedure is repeated until the
cause of the overload has been remedied.
The preset Smart HICCUP output characteristic curve is
optimized for the following applications:
– If only a low short-circuit current is permitted.
– If following an overload or short circuit the output
voltage should be made available again automatically.
UOut [V]
10.1
UN
5s
UN
2
5s
0
IN
IStat. Boost
IDyn. Boost
IOut [A]
0
IN
IStat. Boost
IOut [A]
UN
3
IDyn. Boost
2s
IDyn. Boost 2s
IOut [A]
IOut [A]
8s
0
IDyn. Boost
5s
5s
Figure 21
t [s]
Smart HICCUP output characteristic curve
toff
0
Figure 20
108827_en_00
t [s]
U/I Advanced output characteristic curve
PHOENIX CONTACT
28 / 50
QUINT4-PS/1AC/24DC/40
10.3
FUSE MODE output characteristic curve
11
In the event of an overload (e.g., short circuit), the power
supply switches off the DC output permanently. The value of
the switch-off threshold and the time period for which it may
be exceeded can be freely selected. The power supply is
restarted via the remote contact. As an option, the power
supply can be switched on by switching the supply voltage
on the primary side off and on.
With the fourth generation of the QUINT POWER power
supply, it is now possible for the first time to adapt the
behavior of the power supply. In addition to setting the
output voltage and selecting the output characteristic
curves, you can configure signal outputs Out 1, Out 2, and
floating signal contact 13/14, for example. Configuration of
the remote input for controlling the power supply or
specification of signal options and signal thresholds also
extend the range of possible applications.
The power supply is configured via the device's internal NFC
(near field communication) interface. This is located behind
the QR code on the front.
IOut [A]
Selecting the FUSE MODE output characteristic curve sets
the following default values.
– tFuse = 100 ms
– IFuse = IN
The power supply behaves like a passive
NFC tag. An auxiliary power source is
required in order to supply the power supply
with configuration data.
IFuse
11.1
0
tFuse
t [s]
Figure 22
108827_en_00
Configuring the power supply
FUSE MODE output characteristic curve
Configuration with PC software
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– PC or notebook (as of Windows 7, Microsoft.Net
Framework 4.5, USB 2.0 interface, 50 MB hard disk
capacity, QUINT POWER software).
– Programming adapter:
TWN4 MIFARE NFC USB ADAPTER (Order No.
2909681) is plugged into the USB interface.
– Programming software: the QUINT POWER software
has been successfully installed.
PHOENIX CONTACT
29 / 50
QUINT4-PS/1AC/24DC/40
11.2
Configuring the power supply
To configure the power supply, proceed as follows:
– Before you can configure the power supply, it should
either be disconnected from the supply voltage or
switched to SLEEP MODE.
– To switch the power supply to SLEEP MODE, use one
of the external circuits. The following connection
versions are possible between the Rem (remote input)
and SGnd (signal ground) connection terminal blocks.
13
14
Rem
SGnd
Out 1
Out 2
a)
3.1
3.2
3.3
3.4
3.5
3.6
b)
c)
+
< 5 V DC
=
-
Figure 23
–
11.3
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– NFC-capable mobile terminal device with Android
operating system as of Version 4.1.x (Jelly Bean)
– QUINT POWER app (Google Play Store)
For information regarding the configuration of
the power supply, such as selecting the
characteristic curve and output parameters,
please refer to the QUINT POWER app.
SLEEP MODE connection versions
Hold the USB-PROG-ADAPTER in front of the mounted
power supply such that the NFC antenna symbol is over
the QR code.
QUINT POWER Ord.No.29046xx
11.4
Ordering a configured power supply
Customer-specified QUINT POWER power supplies are
ordered as a KMAT item (configurable material) and are
configured during the production process in the factory. The
power supply is therefore supplied ready to connect for your
specific application.
l
na
Sig
UOut
3.1
3.2
3.3
3.4
3.5
3.6
13
14
Rem
nd
SG 1
t
Ou 2
t
Ou
You can type in the the web code
phoenixcontact.net/webcode/#0852
to configure and order your power supply.
st
o
Bo
% t
00
> 15% Pou
> 70%
> 5 OK
DC
CONN
NFC
x8
DAT
M3
Configuration with NFC-capable mobile
terminal device
The QUINT POWER app enables you to conveniently
configure the power supply using a mobile terminal device,
such as a smartphone.
< 15 k
Signal
For information regarding the configuration of
the power supply, such as selecting the
characteristic curve and output parameters,
refer to the user manual for the QUINT
POWER software.
Figure 24
–
Configuration of the power supply
In the programming interface of the QUINT POWER
software, press the [Read] button. The current device
and configuration data for the power supply is read and
displayed.
If a connection cannot be established
between the USB-PROG-ADAPTER and the
power supply, more detailed information can
be found in the user manual for the QUINT
POWER software.
108827_en_00
PHOENIX CONTACT
30 / 50
QUINT4-PS/1AC/24DC/40
Boost currents
The power supply provides the static boost (IStat. Boost) for a
sustained load supply or the time-limited dynamic boost
(IDyn. Boost).
Static Boost
POut [W]
For system expansion purposes, the sustained static boost
(IStat. Boost) supports the load supply with up to 112% of the
nominal current of the power supply. The static boost is
available at an ambient temperature of up to 40°C.
PDyn. Boost
150%
125%
PStat. Boost
PN
-25
40
60
70
TA [°C]
12.2
Performance characteristic in static boost
Dynamic Boost
IOut [A]
Dynamic boost (IDyn. Boost) delivers up to 150 % of the power
supply nominal current to supply high loads. This temporary
power supply to the load lasts a maximum of 5 s at an
ambient temperature of up to 60 °C. The energy supplied
adaptively for the load supply and the recovery time (tPause)
are calculated based on the specific load situation using
algorithms (see recovery time tables).
IDyn.Boost
12.2.1 Recovery times at an ambient temperature of
40 °C
112%
100%
75%
Figure 25
If a current that is lower than the maximum
available dynamic boost current (IDyn. Boost) is
required for the same period, the recovery
time may (tPause) decrease.
IBase Load IDyn. Boost
[A]
[A]
3
4
5
60
0,5
2,0
3,5
5
7
10
60
1,0
2,5
4
6
7
20
60
1,5
3
4
6
8
30
60
2,0
4
5
7
9
40
60
3,0
6
9
13
16
45
60
11
22
33
44
56
Figure 27
tDyn.Boost
Required recovery times at ≤ 40°C
tDyn.Boost
tPause
Basic curve of the dynamic boost process
tDyn. Boost [s]
1
2
3
4
5
0
60
1,5
2,5
4,5
6
7
10
60
1,5
3
5
7
8
20
60
2
4
6
8
10
30
60
3
6
8
11
14
40
60
19
37
56
74
92
Figure 28
108827_en_00
2
12.2.2 Recovery times at an ambient temperature of
60 °C
t [s]
Figure 26
1
0
IBase Load IDyn. Boost
[A]
[A]
IBase Load
tDyn. Boost [s]
tPause [s]
12.1
Use the following tables to determine the required recovery
time (tPause) at the maximum dynamic boost current (IDyn.
Boost) based on the following values:
– IBase Load
– Duration of the boost current (tDyn. Boost)
– Ambient temperature (40 °C or 60 °C)
tPause [s]
12
Required recovery times at ≤ 60°C
PHOENIX CONTACT
31 / 50
QUINT4-PS/1AC/24DC/40
12.2.3 Example: Determining the recovery time
(tPause)
13
At an output current (IBase Load) of 20 A, the dynamic output
current (IDyn. Boost) of 60 A increases for 2 s (tDyn. Boost).
After a recovery time (tPause) of 3 s, the dynamic boost is
available once again.
tDyn. Boost [s]
1
2
3
4
5
0
60
0,5
2,0
3,5
5
7
10
60
1,0
2,5
4
6
7
20
60
1,5
3
4
6
8
30
60
2,0
4
5
7
9
40
60
3,0
6
9
13
16
45
60
11
22
33
44
56
Example recovery time for ≤ 40°C
Loads that are connected in parallel are still supplied with
energy. Operation of these system parts is ensured. In order
to always enable the reliable tripping of circuit breakers and
fuses, certain framework conditions must be observed (see
SFB configuration section).
The U/I Advanced output characteristic curve
supports SFB Technology.
13.1
Tripping circuit breakers
The circuit breaker is tripped by the high SFB current of the
power supply, typically within 3 to 5 ms. As a result, voltage
dips at loads that are connected in parallel are avoided.
I [A]
Figure 29
SFB Technology (selective fuse breaking) can be used to
quickly and reliably trip miniature circuit breakers and fuses
connected on the secondary side. In the event of a short
circuit on the secondary side, the power supply supplies up
to 6 times the nominal current for 15 ms. The faulty current
path is switched off selectively.
tPause [s]
IBase Load IDyn. Boost
[A]
[A]
SFB Technology
6x IN
typ. 3 - 5 ms
IN
0
Figure 30
13.2
t [s]
SFB pulse trips circuit breakers
Tripping a fuse
Fuses are tripped by melting the predetermined breaking point
inside the fuse capsule. The tripping characteristic of the fuse is
described by the melting integral (I²t). A high current is crucial
in order to achieve a very short tripping time.
13.3
SFB configuration
Observe the following framework conditions for determining
the maximum distance between the power supply and load:
– The performance class of the power supply
– The cross section of the connecting cable
– The tripping characteristic of the fuse component
Power supply unit
+
+
-
-
Load
l
Figure 31
108827_en_00
Schematic diagram of the maximum cable length
PHOENIX CONTACT
32 / 50
QUINT4-PS/1AC/24DC/40
13.4
Maximum distance between the power supply and load
The distances given in the table are worst-case values and therefore cover the entire tolerance range for the magnetic tripping
of circuit breakers. The possible distances are often greater in practice.
13.4.1 Thermomagnetic device circuit breaker, type: Phoenix Contact CB TM1 SFB
Maximum distance l [m] with device circuit
breaker
Phoenix Contact
CB TM1 1A SFB P
CB TM1 2A SFB P
CB TM1 3A SFB P
CB TM1 4A SFB P
CB TM1 5A SFB P
CB TM1 6A SFB P
CB TM1 8A SFB P
CB TM1 10A SFB P
CB TM1 12A SFB P
CB TM1 16A SFB P
Conductor cross section
A [mm²]
AWG
0.75
19
27
18
13
10
8
7
-----
1.0
18
36
25
18
14
11
9
7
5
---
1.5
16
54
37
27
21
17
14
11
7
5
3
2.5
14
91
63
46
35
29
24
19
12
9
5
4.0
12
< 130
< 100
73
57
46
39
31
20
14
8
6.0
10
< 200
< 140
< 100
86
70
58
46
30
21
12
10.0
8
< 300
< 220
< 160
< 140
< 100
97
78
51
36
20
The cable lengths determined are based on the following parameters:
Tripping:
DC correction factor (0 Hz):
Characteristics:
Ambient temperature:
Internal resistance Ri of the device circuit
breaker:
Comments:
108827_en_00
magnetic
Phoenix Contact = 1,0
C
Characteristic C (10 times the rated current) x correction factor
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT
33 / 50
QUINT4-PS/1AC/24DC/40
13.4.2 Thermomagnetic circuit breaker, type: Siemens 5SY, ABB S200
Maximum distance l [m] with circuit breaker Conductor cross section
A [mm²]
0.75
1.0
AWG
18
(17)
Siemens 5SY
A1
78
105
A1.6
58
77
A2
49
65
A3
35
47
A4
27
36
A6
18
25
A8
14
19
A10
11
15
A13
8
11
A16
7
9
A20
5
7
A25
4
5
A32
2
3
A40
1
2
B2
28
37
B4
16
21
B6
10
14
B10
6
9
B13
5
6
B16
3
4
B20
2
3
B25
1
2
C1
10
14
C1.6
12
17
C2
11
15
C3
9
12
C4
7
9
C6
5
6
C8
3
4
C10
2
2
C13
1
1
108827_en_00
1.5
16
157
116
98
71
54
37
28
23
17
14
11
8
5
3
56
32
21
13
10
7
4
3
21
25
23
18
14
10
6
4
2
2.5
14
263
194
164
118
90
62
48
38
29
24
19
13
8
5
93
53
36
23
17
11
7
5
35
42
39
30
24
16
11
7
4
4.0
12
420
311
262
190
144
100
76
61
47
39
31
21
13
8
149
85
57
36
27
18
12
8
56
68
62
48
38
27
17
11
6
6.0
10
631
467
394
285
217
150
115
92
71
58
46
32
20
13
224
128
86
55
41
28
18
12
84
102
94
72
58
40
26
17
10
PHOENIX CONTACT
10.0
8
1052
779
657
475
362
250
192
154
119
97
78
53
33
22
374
214
144
92
68
47
30
20
141
171
157
121
97
67
44
29
17
34 / 50
QUINT4-PS/1AC/24DC/40
Maximum distance l [m] with circuit breaker Conductor cross section
A [mm²]
0.75
1.0
AWG
18
(17)
ABB S200
B6
10
13
B8
8
10
B10
6
8
B13
4
5
B16
3
4
B20
1
2
B25
1
1
C1
3
4
C1.6
7
10
C2
7
9
C3
8
10
C4
6
8
C6
4
5
C8
2
3
C10
1
2
C13
1
1
Z1
64
85
Z1.6
46
62
Z2
42
57
Z3
33
44
Z4
24
33
Z6
16
21
Z8
12
17
Z10
10
14
Z16
6
9
1.5
16
20
16
12
8
6
3
2
6
15
14
16
12
8
5
3
2
128
93
85
66
49
32
25
21
13
2.5
14
33
26
21
14
10
6
4
11
25
23
26
20
14
9
6
3
214
156
143
110
82
54
42
36
22
4.0
12
53
43
34
23
16
10
6
17
41
38
42
32
23
15
9
5
343
250
229
176
132
87
68
57
36
6.0
10
80
64
51
35
24
15
10
26
62
57
64
48
34
23
14
8
514
375
343
264
198
131
102
86
54
10.0
8
133
107
85
59
41
26
17
44
103
95
107
81
57
38
24
13
857
625
573
441
331
219
171
144
90
The cable lengths determined are based on the following parameters:
Tripping:
DC correction factor (0 Hz):
Characteristics:
Ambient temperature:
Internal resistance Ri of the device circuit
breaker:
Comments:
108827_en_00
magnetic
Siemens = 1.4; ABB = 1.5
A, B, C, Z
Characteristic A (3 times the rated current) x correction factor
Characteristic B (5 times the rated current) x correction factor
Characteristic C (10 times the rated current) x correction factor
Characteristic Z (3 times the rated current) x correction factor
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT
35 / 50
QUINT4-PS/1AC/24DC/40
13.4.3 Fuse, type: Cooper Bussmann GMA xA, GMC xA
Maximum distance l [m] with
fuse
Cooper Bussmann GMA 1A
GMA 1.25A
GMA 1.5A
GMA 1.6A
GMA 2A
GMA 2,5A
GMA 3A
GMA 3,15A
GMA 3,5A
GMA 4A
GMA 5A
GMC 1A
GMC 1,25A
GMC 1,5A
GMC 1,6A
GMC 2A
GMC 2.5A
GMC 3A
GMC 3,15A
GMC 3,5A
GMC 4A
Melting integral I²t Conductor cross section
[A²s]
A [mm²]
0.75 1.0
AWG
18
(17)
0.48
48
64
0.84
36
49
1.6
26
35
2
23
31
3.1
19
25
4.9
15
20
8.8
11
15
9.7
10
14
13
9
12
19
7
10
29
6
8
1.8
23
31
3.4
17
23
5.4
13
18
5.8
13
18
8.9
11
14
13
9
12
19
7
10
23
6
9
25
6
8
36
5
7
1.5
16
97
73
53
47
38
30
22
21
18
15
12
47
34
27
27
22
18
15
13
13
11
2.5
14
162
122
88
79
63
51
37
36
31
25
20
78
58
46
45
37
30
25
23
22
18
4.0
12
259
196
141
127
101
81
60
57
49
41
33
125
93
74
72
59
49
41
37
35
29
6.0
10
388
294
212
190
152
122
90
86
74
61
50
188
139
111
108
89
74
61
55
53
44
10.0
8
648
490
354
317
254
204
151
144
124
103
83
314
233
185
180
149
123
103
93
89
74
The cable lengths determined are based on the following parameters:
Tripping:
Characteristics:
Ambient temperature:
Internal resistance Ri of the fuse:
Comments:
108827_en_00
thermal
Cooper Bussmann GMA (fast-blow - fast acting)
Cooper Bussmann GMC (medium-blow - medium time delay)
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT
36 / 50
QUINT4-PS/1AC/24DC/40
14
Signaling
14.1
A floating signal contact and two digital outputs are available
for preventive function monitoring of the power supply.
Depending on the configuration of the power supply, either
the two digital outputs or one digital and one analog output
can be selected. The signal outputs are electrically isolated
from the input and output of the power supply.
UOut
29,5V
9
The current device status of the power supply is signaled
using four LED status indicators. The function of each LED
status indicator is assigned to a fixed event.
8
13
14
Rem
SGnd
Out 1
Out 2
Signal
1
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75% P
Out
> 50%
DC OK
6
Figure 32
2
3
4
5
Position of signaling elements
Key
No.
1
2
3
4
5
6
7
8
9
108827_en_00
24V
7
In addition, the power supply can be switched off and on via
an external circuit.
The signal outputs are configured on the software side using
the QUINT POWER software or the QUINT POWER app.
Upon delivery, the power supply is pre-allocated a default
configuration for the signal outputs.
Location and function of the signaling elements
Signaling elements
13/14 floating switch contact (N/O contact)
Rem, remote input (switch power supply off and on)
SGnd, signal ground (reference potential for signals
Out 1, Out 2)
Out 1 (digital output, function depends on the signal
option set)
Out 2 (digital or analog output, function depends on
the signal option set)
LED status indicator DC OK
LED on: UOut > 90% x USet
LED flashing: UOut 50 % (output power
>480 W)
LED status indicator POut >75 % (output power
>720 W)
LED status indicator POut >100 %, boost mode (output power >960 W)
PHOENIX CONTACT
37 / 50
QUINT4-PS/1AC/24DC/40
14.1.1 Floating signal contact
14.1.3 Active analog signal output
In the default configuration, the floating switch contact
opens to indicate that the set output voltage has been
undershot by more than 10 % (UOut 75% LED lights up green in addition
to the > 50% LED. If the required output power is then
greater than the nominal device power, the power supply
operates in boost mode. In boost mode, the > 100% LED
additionally lights up yellow.
b)
c)
+
10-24 V DC
-
Figure 37
3.1
3.2
3.3
3.4
3.5
3.6
PNP output
Four LED status indicators are integrated in the front of the
power supply, which indicate the current device state.
External wiring versions, enable
SLEEP MODE
Signal
PLC
a)
Gnd
14.5
b)
-
13
14
Rem
SGnd
Out 1
Out 2
13
14
Rem
SGnd
Out 1
Out 2
a)
3.1
3.2
3.3
3.4
3.5
3.6
Figure 36
Signal
Figure 38
< 15 k
Signal
When using a PLC output, select the following external
circuit version to switch the power supply to SLEEP MODE.
=
External wiring versions, disable
SLEEP MODE
PHOENIX CONTACT
41 / 50
QUINT4-PS/1AC/24DC/40
14.6
U/I Advanced characteristic curve signaling
The following table shows the standard assignment for signaling for the U/I Advanced characteristic curves which is set by
default.
LED: POut >100 %
yellow
Signal Out 2: POut < PN
Default
Normal operation
BOOST
Overload operation
POut < PN
POut > PN
UOut < 0.9 x USet
Active High
Active Low
Active Low
closed
closed
open
Active High
Active High
Active Low
LED: POut > 75 %
LED: POut > 50 %
green
LED: DC OK
Relay: 13/14, DC OK
Default
Signal Out 1: DC OK
LED off
Figure 39
14.7
LED on
LED flashing
Signal image for U/I Advanced
SMART HICCUP characteristic curve signaling
The following table shows the standard assignment for signaling for the SMART HICCUP characteristic curve.
LED: POut >100 %
Signal Out 2: POut < PN
Normal operation
BOOST
Overload operation
POut < PN
POut > PN
UOut < 0.9 x USet
Active High
Active Low
Active Low
Yellow
Default
LED: POut > 75 %
LED: POut > 50 %
Green
LED: DC OK
Closed
Relay: 13/14, DC OK
Closed
Open
Default
Signal Out 1: DC OK
Active High
LED off
Figure 40
108827_en_00
LED on
Active High
Active Low
LED flashing
Signal image for SMART HICCUP
PHOENIX CONTACT
42 / 50
QUINT4-PS/1AC/24DC/40
14.8
FUSE MODE characteristic curve signaling
The following table shows the standard assignment for signaling for the FUSE MODE characteristic curve.
LED: POut >100 %
Yellow
Signal Out 2: POut < PN
Default
Normal operation
BOOST
POut < PN
POut > PN
Active High
Active Low
Active Low
Closed
Closed
Open
Active High
Active High
Active Low
FUSE MODE
I > IFuse
for t > tFuse
LED: POut > 75 %
LED: POut > 50 %
Green
LED: DC OK
Relay: 13/14, DC OK
Default
Signal Out 1: DC OK
LED off
Figure 41
14.9
LED on
LED flashing
Signal image for FUSE MODE
SLEEP MODE signaling
In SLEEP MODE, all LEDs are off, all signals are low, and the relay switching contact is open.
108827_en_00
PHOENIX CONTACT
43 / 50
QUINT4-PS/1AC/24DC/40
14.10 Special immunity for the signal level
14.10.1 Surge protection for the high-voltage area at the power plant
Surge protection (Phoenix Contact Order No.: 2907925 or comparable protection) must be implemented for power plant
applications when using signal connection types t (telecommunications area), h (high voltage area) or f (field) in accordance
with IEC/EN 61850-3 or signal connection types 3 (process area) and 4 (high voltage area) in accordance with EN 61000-6-5.
When using the digital signals, a relay (Phoenix Contact Order No.: 2900299 or a comparable relay) can be implemented.
14.10.2 Surge protection for signals in railway applications
Surge protection (Phoenix Contact Order No.: 2907925 or comparable protection) must be implemented for railway
applications when using signals in accordance with EN 62236-4 and EN 50121-4.
When using the digital signals, a relay (Phoenix Contact Order No.: 2900299 or a comparable relay) can be implemented.
14.10.3 Surge protection for devices in use in safety-related systems
Surge protection (Phoenix Contact Order No.: 2907925 or comparable protection) must be implemented for railway
applications when using signals in accordance with EN 61000-6-7 for devices provided to perform functions in safety-related
systems (functional safety) in industrial settings.
When using the digital signals, a relay (Phoenix Contact Order No.: 2900299 or a comparable relay) can be implemented.
UOut
Signal
13
14
Rem
SGnd
Out 1
Out 2
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75%
POut
> 50%
PLC
Digital Input
5
6
1
2
3
4
DI x 0/24 V DC
GND
DC OK
Figure 42
UOut
Schematic diagram, signal wiring with TRABTECH surge protection
Signal
13
14
Rem
SGnd
Out 1
Out 2
> 100% Boost
> 75%
POut
> 50%
DC OK
Figure 43
108827_en_00
3.1
3.2
3.3
3.4
3.5
3.6
A2-
A1+
11/13(+)
A2
11
A1
14
14
PLC
Digital Input
DI x 0/24 V DC
GND
12
Schematic diagram, signal wiring with relay module
PHOENIX CONTACT
44 / 50
QUINT4-PS/1AC/24DC/40
15
Operating modes
15.2
15.1
Series operation
You can connect several power supplies in parallel in order
to increase the power or to supply the loads redundantly.
To double the output voltage, connect two power supplies in
series. Only use power supplies with the same performance
class and configuration for series operation. If two 24 V DC
power supplies are connected in series, an output voltage of
48 V DC is available to supply the loads.
+
+
-
-
IN
+ −
-48 V
Figure 45
+
-
-
Figure 44
-24 V
+ −
-
+48 V
+
IN
+ −
+
−
+
+24 V
Parallel operation
Σ = IN
Schematic diagram in parallel operation
+
-
Schematic diagrams in series operation
Observe the following points when carrying out parallel
connection:
1. Use power supplies of the same type and performance
class
2. Setting the same output voltages
3. Using the same cable cross sections for wiring
4. Using the same cable lengths for the DC convergence
point
5. Operating power supplies in the same temperature
environment
6. When three or more power supplies are connected in
parallel, each output must be protected (e.g., with
circuit breakers, fuses or decoupling modules)
We recommend the configuration "parallel
operation" for a parallel connection.
For more detailed information on the
operating mode for parallel operation, refer to
the user manual for the QUINT POWER
software or the QUINT POWER app.
108827_en_00
PHOENIX CONTACT
45 / 50
QUINT4-PS/1AC/24DC/40
15.2.1 Redundancy operation
Redundant circuits are suitable for supplying systems and
system parts which place particularly high demands on
operational reliability.
If energy is to be supplied to the load with 1+1 redundancy,
two power supplies of the same type and performance class
must be used. In the event of an error, it must be ensured
that one of the power supplies is able to provide the total
required power for the load. This means that in redundancy
mode, two 20 A power supplies supply a load with a nominal
current of 20 A, for example. During normal operation of the
power supplies, each power supply therefore supplies 10 A.
Always use cables with the same cross sections and lengths
when wiring the power supplies on the DC output side.
redundancy operation, the power supplies are operated with
maximum half the nominal power. The keepout areas are
therefore reduced.
Using the signaling settings, you can monitor whether both
power supplies are being operated with ≤ half the nominal
load. In the case of system extension, an overload is
prevented if one of the power supplies fails.
15.2.2 Increased power
When n power supplies are connected in parallel, the output
current is increased to n x IN. Parallel connection for
increased power is used when extending existing systems.
If the individual power supply does not cover the current
consumption of the most powerful load, parallel connection
of power supplies is recommended.
Redundancy modules can be used to 100% decouple two
power supplies from one another and to ensure the supply.
A distinction is made here between passive and active
redundancy modules. Optimum decoupling with
simultaneous monitoring and minimal power dissipation can
be achieved with the QUINT ORING or QUINT S-ORING
active redundancy module.
IN
When three or more power supplies are
connected in parallel, each output must be
protected separately, e.g., by a circuit
breaker, fuse or decoupling module such as
QUINT ORING, QUINT S-ORING or
QUINT DIODE.
IN
+ −
+ −
IN
IN
+ –
+ –
+
−
+
–
Σ = IN
+ −
Figure 46
Schematic diagram, redundant operation with
QUINT ORING
+ –
Figure 48
IN
IΣ= 2 x IN
Schematic diagram of increased performance
IN
+ −
+ −
+
−
Σ = IN
Figure 47
Schematic diagram, redundant operation with
QUINT S-ORING
Certain specifications apply in redundancy operation with
regard to the configuration of the keepout areas. In
108827_en_00
PHOENIX CONTACT
46 / 50
QUINT4-PS/1AC/24DC/40
16.3
Derating
The QUINT POWER power supply runs in nominal
operation without any limitations. For operation outside the
nominal range, the following points should be observed
depending on the type of use.
16.1
Ambient temperature
POut [W]
When operating the power supply at an ambient
temperature of > 60 °C, a power derating of 2.5 %/K should
be observed. Up to an ambient temperature of 40 °C, the
power supply can take power from the static boost for a
sustained period. In the 40 °C to 60 °C temperature range,
the power supply can output more than the nominal power
for a sustained period.
Installation height
The power supply can be operated at an installation height
of up to 2000 m without any limitations. Different data
applies for installation locations above 2000 m due to the
differing air pressure and the reduced convection cooling
associated with this (see technical data section). The data
provided is based on the results of pressure chamber testing
performed by an accredited test laboratory.
POut [%]
16
175
150
125
100
75
PDyn. Boost
150%
25
0
= PN 100 % 60 °C
= PStat.112 % 40 °C
= PDyn. 150 % 60 °C
50
0
1000
2000
3000
4000
125%
PStat. Boost
PN
112%
100%
75%
-25
40
60
5000
H [m]
Figure 50
Output power depending on the installation
height
70
TA [°C]
Figure 49
16.2
Output power depending on the ambient
temperature
Input voltage
UIn
< 100 V AC
< 110 V DC
< 115 V AC
< 110 V DC
108827_en_00
Derating 1 %/V
TA
IOut
≤ 60 °C
IN
≤ 40 °C
IStat. Boost
UOut
24 V DC
PHOENIX CONTACT
47 / 50
QUINT4-PS/1AC/24DC/40
16.4
Position-dependent derating
The fanless convection-cooled power supply can be snapped onto all DIN rails according to EN 60715.
The power supply should be mounted horizontally for heat dissipation reasons (AC connection terminal blocks
facing downward). Please observe the derating for any mounting other than the normal mounting position.
Reduce the output power based on the prevailing ambient temperature.
The recommended output power for different mounting positions and ambient temperatures can be found in the
characteristic curves below.
Exceeding these values will reduce the service life of the power supply.
Pout [%]
16.4.1 Normal mounting position
150
125
Ord.No.29046xx
QUINT POWER
175
100
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
75
na
l
>1
> 700%
> 55% Boo
s
DC0% P t
OK out
3.1
3.2
3.3
3.4
3.5
3.6
50
25
= PN 100 %
= PStat. 112 %
= PDyn. 150 %
0
-25 0
10
20
30
40
50
60
Y
70
80
T [°C]
Z
X
Pout [%]
16.4.2 Rotated mounting position 90° Z-axis
175
150
125
100
75
M
3x
8
50
INT
13
14
Signal
3.1
3.2
3.3
3.4
3.5
3.6
Y
25
POW
ER
UOut
Rem
SGnd
Out 1
Out 2
> 100% Boost
> 75%
> 50% Pout
DC OK
QU
Ord
.No.
29
046x
x
= PN 100 %
= PStat.112 %
= PDyn. 150 %
0
-25 0
10
20
30
40
50
60
70
80
T [°C]
Z
X
108827_en_00
PHOENIX CONTACT
48 / 50
QUINT4-PS/1AC/24DC/40
Pout [%]
16.4.3 Rotated mounting position 180° Z-axis
175
150
125
100
75
50
25
>1
3.6
> 700 %
> 55% Boo
DC0% P st
OK Out
0
-25 0
13
14
Re
m
SG
n
Ou d
t
Ou 1
t2
3.3
3.4
3.5
3.1
3.2
Sig
na
l
Out
Z
U
X
10
20
30
40
50
60
70
80
T [°C]
QUINT POWEROrd.No.29046xx
Y
= PN 100 %
= PStat.112 %
= PDyn. 150 %
Pout [%]
16.4.4 Rotated mounting position 270° Z-axis
175
150
125
100
Signal
OW
E
x
6x
04
o.2
9
UOut
50
> 100% Boost
> 75% Pout
> 50%
DC OK
QU
INT
P
.N
R
Ord
Y
13
3.1
14
3.2
3.3
Rem
3.4
SGnd
Out 1
3.5
Out 2
3.6
75
25
= PN 100 %
= PStat. 112 %
= PDyn. 150 %
0
-25 0
10
20
30
40
50
60
70
80
T [°C]
Z
X
108827_en_00
PHOENIX CONTACT
49 / 50
QUINT4-PS/1AC/24DC/40
U
IN
T
10 %
> 75 %
> 50 OK
> C
D
l 1
na 3. 2
ig
3. 3
S
3. 4
3.
5
3.
13
6
3.
14
em
R nd
st
G 1
S ut 2
oo
B ut
O ut
o
O
0% P
Pout [%]
Q
ut
UO
P
O
W
E
R
O
rd
.N
o.
2
90
46
xx
16.4.5 Rotated mounting position 90° X-axis
175
150
125
100
75
50
25
= PN 100 %
= PStat. 112 %
= PDyn. 150 %
0
-25 0
10
20
30
40
50
60
70
80
T [°C]
Y
Z
X
Pout [%]
16.4.6 Rotated mounting position 270° X-axis
175
150
125
100
75
50
25
= PN 100 %
= PStat.112 %
= PDyn. 150 %
0
-25 0
10
20
30
40
50
Y
60
70
80
T [°C]
Z
X
108827_en_00
PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
phoenixcontact.com
50 / 50