QUINT4-PS/1AC/48DC/20
Power supply unit
Data sheet
109981_en_00
1
© PHOENIX CONTACT 2022-02-25
Description
QUINT POWER power supplies with SFB Technology and
preventive function monitoring ensure superior system
availability.
Technical data (short form)
Powerful
Mains buffering
–
–
SFB Technology: 6 times the nominal current for 15 ms
Power reserves:
Static boost of up to 125% (PN) for a sustained period
Dynamic boost of up to 200% (PN) for 5 s
Robust
–
–
Mains buffering ≥ 20 ms
High degree of electrical immunity, thanks to integrated
gas discharge tube (6 kV)
Preventive
–
Comprehensive signaling:
Analog signal, digital signal, relay contact, LED bar
graph
Can be ordered pre-configured
–
Perform configuration online and order 1 or more units
Input voltage range
100 V AC ... 240 V AC 15 % ... +10 %
typ. 27 ms (120 V AC)
typ. 28 ms (230 V AC)
Nominal output voltage (UN)
48 V DC
Nominal output current (IN)
Static Boost (IStat.Boost)
Dynamic Boost (IDyn.Boost)
Selective Fuse Breaking (ISFB)
20 A
22.5 A
30 A (5 s)
105 A (15 ms)
Efficiency
typ. 95.2 % (120 V AC)
typ. 96.2 % (230 V AC)
Setting range of the output voltage
(USet)
Output power (PN)
Output power (PStat. Boost)
Output power (PDyn. Boost)
Residual ripple
MTBF (IEC 61709, SN 29500)
Ambient temperature (operation)
Dimensions W/H/D
Weight
48 V DC ... 56 V DC
960 W
1080 W
1440 W
< 50 mVPP
> 569000 h (40 °C)
-25 °C ... 70 °C
-40°C (startup type tested)
> 60 °C Derating: 2,5 %/K
120 mm / 130 mm / 140 mm
2.85 kg
Long service life
–
Well over 15 years
All technical specifications are nominal values and refer to a room temperature of 25 °C and 70 % relative humidity
at 100 m above sea level.
QUINT4-PS/1AC/48DC/20
2
Table of contents
2
Table of contents ..................................................................................................................... 2
1
3
4
Description .............................................................................................................................. 1
Ordering data .......................................................................................................................... 3
Technical data ......................................................................................................................... 4
5
Safety and installation notes .................................................................................................. 15
7
Structure of the power supply ................................................................................................ 19
6
8
9
10
11
12
13
High-voltage test (HIPOT) ..................................................................................................... 17
Mounting/removing the power supply .................................................................................... 22
Device connection terminal blocks ........................................................................................ 25
Output characteristic curves .................................................................................................. 27
Configuring the power supply ................................................................................................ 30
Boost currents ....................................................................................................................... 31
SFB Technology .................................................................................................................... 33
14
Signaling................................................................................................................................ 38
16
Derating................................................................................................................................. 48
15
Operating modes ................................................................................................................... 46
109981_en_00
PHOENIX CONTACT
2/51
QUINT4-PS/1AC/48DC/20
3
Ordering data
Description
Type
Item no.
Pcs./Pkt.
QUINT POWER primary-switched power supply with free QUINT4-PS/1AC/48DC/20
choice of output characteristic curve, SFB (Selective Fuse
Breaking) Technology, and NFC interface, input: 1-phase,
output: 48 V DC/20 A
2904612
1
Accessories
Type
Item no.
Pcs./Pkt.
2-piece universal wall adapter for securely mounting the
device in the event of strong vibrations. The profiles that
are screwed onto the side of the device are screwed
directly onto the mounting surface. The universal wall
adapter is attached on the left/right.
UWA 130
2901664
1
Near Field Communication (NFC) programming adapter
with USB interface for the wireless configuration of NFCcapable products from PHOENIX CONTACT with
software. No separate USB driver is required.
TWN4 MIFARE NFC USB
ADAPTER
2909681
1
PLT-SEC-T3-230-FM-UT
2907919
5
End clamp, material: Aluminum, color: silver
E/AL-NS 35
1201662
10
Versions of the primary-switched QUINT POWER power supply with SFB Technology (selective fuse
breaking), which are configured online, can now be ordered in batches of one or more using the following web
code: phoenixcontact.net/webcode/#0852
Universal wall adapter for securely mounting the device in UWA 182/52
the event of strong vibrations. The device is screwed
directly onto the mounting surface. The universal wall
adapter is attached on the top/bottom.
Type 2/3 surge protection, consisting of protective plug
and base element with screw connection. For singlephase power supply network with integrated status
indicator and remote signaling. Nominal voltage:
230 V AC/DC
Type 2/3 surge protection, consisting of protective plug
and base element with Push-in connection. For singlephase power supply network with integrated status
indicator and remote signaling. Nominal voltage:
230 V AC/DC
PLT-SEC-T3-230-FM-PT
2938235
2907928
1
5
The range of accessories is being continuously extended. The current range of accessories can be found in
the download area for the product.
109981_en_00
PHOENIX CONTACT
3/51
QUINT4-PS/1AC/48DC/20
4
Technical data
Input data
Unless otherwise stated, all data applies for 25°C ambient temperature, 230 V AC input voltage, and nominal
output current (IN).
Input voltage range
Electric strength, max.
Frequency range (fN)
100 V AC ... 240 V AC -15 % ... +10 %
110 V DC ... 250 V DC -18 % ... +40 %
300 V AC 60 s
50 Hz ... 60 Hz -10 % ... +10 %
Frequency (fR) for railway power supply systems
16.7 Hz (acc. to EN 50163)
Current draw typ.
13.6 A (100 V AC)
5.4 A (240 V AC)
12 A (110 V DC)
5 A (250 V DC)
Railway power supply systems can be operated at 16.7 Hz. Use conditions and technical data on request.
The specified values for current consumption apply for operation in the static boost (PN x 125%).
Discharge current to PE
typical
Mains buffering
Inrush current limitation after 1 ms
Inrush
current integral (I2t)
Input fuse slow-blow, internal
< 3.5 mA
1.7 mA (264 V AC, 60 Hz)
typ. 27 ms (120 V AC)
typ. 28 ms (230 V AC)
12 A
< 1 A2s
16 A
During the first few microseconds, the current flow into the filter capacitors is excluded.
The SCCR value (short-circuit current rating) of the power supply unit corresponds to the SCCR value of the
backup fuse (see input protection table).
The external backup fuse must be approved for the (AC) supply voltage used and the voltage level.
109981_en_00
PHOENIX CONTACT
4/51
QUINT4-PS/1AC/48DC/20
Input protection , AC/DC ( to be connected externally upstream )
Input current IIn
Input protection
Characteristics
4A
A
-
6A
-
10 A
-
13 A
16 A
20 A
Neozed fuse
or equivalent
Circuit breaker
B
-
C
-
-
-
D
K
gG
-
-
-
-
-
Power switch
≤ 13 x IIn
(maximum magnetic tripping)
-
-
-
-
-
-
-
-
-
Electric strength of the insulation
Housing
Input
Signaling
(+)
L
N
(-)
B
B
A
D
Output
PE
+
C
A
Type test (IEC/EN 60950-1)
2.5 kV AC
Field test (with gas-filled surge arrester)
0.8 kV AC
1.1 kV DC
Production test
Field test (gas-filled surge arrester de-contacted)
109981_en_00
2 kV AC
2 kV AC
2.83 kV DC
B
4 kV AC
C
0.5 kV DC
D
0.5 kV DC
2 kV AC
0.5 kV DC
0.5 kV DC
2 kV AC
2.83 kV DC
0.5 kV DC
0.5 kV DC
0.8 kV AC
1.1 kV DC
0.5 kV DC
0.5 kV DC
PHOENIX CONTACT
5/51
QUINT4-PS/1AC/48DC/20
Power Factor
POWER factor
1,0
ij
0,9
Ĵ
0,8
0,7
ij = UIn: 120 V AC/UOut: 48 V DC
Ĵ = UIn: 230 V AC/UOut: 48 V DC
0,6
0,5
10
5
15
20
25
30
IOut [A]
Crest factor
120 V AC
typ. 1,66
230 V AC
typ. 1,63
IIn [A]
Input current vs. output current
15,0
ij = UIn: 120 V AC/UOut: 48 V DC
12,0 Ĵ = UIn: 230 V AC/UOut: 48 V DC
9,0
ij
6,0
3,0
0,0
0
Ĵ
5
10
15
20
30
25
IOut [A]
Input connection data
Connection method
Screw connection
Conductor cross section, rigid
0.2 mm² ... 6 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.25 mm² ... 4 mm²
Conductor cross section, flexible
0.2 mm² ... 4 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.25 mm² ... 4 mm²
Stripping length
8 mm
Conductor cross section AWG
24 ... 10
Tightening torque
0.5 Nm ... 0.6 Nm
109981_en_00
PHOENIX CONTACT
6/51
QUINT4-PS/1AC/48DC/20
Output data
Nominal output voltage (UN)
Setting range of the output voltage (USet) ( constant
capacity )
48 V DC
48 V DC ... 56 V DC
Nominal output current (IN)
20 A
Dynamic Boost (IDyn.Boost)
30 A (5 s)
Static Boost (IStat.Boost)
22.5 A
Selective Fuse Breaking (ISFB)
105 A (15 ms)
Control deviation Static load change 10 % ... 90 %
< 0.5 %
Magnetic circuit breaker tripping
A1...A40 / B2...B25 / C1...C13 / Z1...Z16
Control deviation Dynamic load change 10 % ... 90 %, (10 < 1 %
Hz)
Control deviation change in input voltage ±10 %
< 0.25 %
No-load proof
yes
Short-circuit-proof
Residual ripple ( with nominal values )
Connection in parallel
Connection in series
Feedback voltage resistance
Protection against overvoltage at the output (OVP)
Output connection data
Connection method
yes
< 50 mVPP
yes, for redundancy and increased capacity
yes
≤ 60 V DC
≤ 60 V DC
Screw connection
Conductor cross section, rigid
0.5 mm² ... 16 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.5 mm² ... 16 mm²
Conductor cross section, flexible
0.5 mm² ... 16 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.5 mm² ... 16 mm²
Stripping length
10 mm
Conductor cross section AWG
20 ... 6
Tightening torque
1.2 Nm ... 1.5 Nm
LED signaling
POut > 100 %
LED lights up yellow, output power > 960 W
POut > 75 %
LED lights up green, output power > 720 W
UOut > 0.9 x USet
LED lights up green
POut > 50 %
UOut < 0.9 x USet
109981_en_00
LED lights up green, output power > 480 W
LED flashes green
PHOENIX CONTACT
7/51
QUINT4-PS/1AC/48DC/20
Signal contact (configurable)
Signal output (configurable) Out 1
Digital
Default
Signal output (configurable) Out 2
Digital
Analog
0 / 24 V DC , , 20 mA
24 V DC , 20 mA ( 24 V DC for UOut > 0.9 x USet )
0 / 24 V DC , , 20 mA
4 mA ... 20 mA ±5 % (Load ≤400 Ω)
Default
Relay contact (configurable) 13/14
Function
Default
Maximum contact load
Control input (configurable) Rem
Function
Default
Signal ground SGnd
Signal connection data
Connection method
24 V DC , 20 mA ( 24 V DC for POut 0.9 USet)
24 V DC 1 A , 30 V AC/DC 0.5 A
Output power ON/OFF (SLEEP MODE)
Output power ON (>40 kΩ/24 V DC/open bridge between Rem
and SGnd)
Reference potential for Out1, Out2, and Rem
Push-in connection
Conductor cross section, rigid
0.2 mm² ... 1 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.2 mm² ... 0.75 mm²
Conductor cross section, flexible
0.2 mm² ... 1.5 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.2 mm² ... 1.5 mm²
Stripping length
8 mm
Conductor cross section AWG
24 ... 16
Reliability
230 V AC
MTBF (IEC 61709, SN 29500)
Life expectancy (electrolytic capacitors)
Output current (IOut)
10 A
20 A
20 A
109981_en_00
> 949000 h (25 °C)
> 569000 h (40 °C)
> 260000 h (60 °C)
120 V AC
230 V AC
> 367000 h ( 40 °C )
> 452000 h ( 40 °C )
> 155000 h ( 40 °C )
> 440000 h ( 25 °C )
> 217000 h ( 40 °C )
> 614000 h ( 25 °C )
The expected service life is based on the capacitors used. If the capacitor specification is observed, the
specified data will be ensured until the end of the stated service life. For runtimes beyond this time, error-free
operation may be reduced. The specified service life of more than 15 years is simply a comparative value.
PHOENIX CONTACT
8/51
QUINT4-PS/1AC/48DC/20
Switching frequency
Min.
PFC stage
50 kHz
Main converter stage
45 kHz
Auxiliary converter stage
Max.
500 kHz
85 kHz
General data
Degree of protection
107 kHz
200 kHz
IP20
Protection class
I
Side element version
Aluminum
Dimensions W / H / D (state of delivery)
120 mm / 130 mm / 140 mm
Inflammability class in acc. with UL 94 (housing / terminal V0
blocks)
Hood version
Stainless steel X6Cr17
Weight
2.85 kg
Power dissipation
Maximum no-load power dissipation
Power loss nominal load max.
Eta [%]
0.8 kV AC / 1.1 kV DC,
the gas-filled surge arrester must be
disconnected.
The test voltage should rise and fall in ramp form.
The relevant rise and fall time of the ramp should
be at least two seconds.
6.1
High-voltage dielectric test (dielectric strength
test)
In order to protect the user, power supplies (as electric
components with a direct connection to potentially
hazardous voltages) are subject to more stringent safety
requirements. For this reason, permanent safe electrical
isolation between the hazardous input voltage and the
touch-proof output voltage as safety extra-low voltage
(SELV) must always be ensured.
In order to ensure permanent safe isolation of the AC input
circuit and DC output circuit, high-voltage testing is
performed as part of the safety approval process (type test)
and manufacturing (routine test).
6.2
High-voltage dielectric test during the
manufacturing process
During the manufacturing process for the power supply, a
high-voltage test is performed as part of the dielectric test in
accordance with the specifications of IEC/UL/EN 61010-1.
The high-voltage test is performed with a test voltage of at
least 1.5 kV AC / 2.2 kV DC or higher. Routine
manufacturing tests are inspected regularly by a certification
authority.
109981_en_00
PHOENIX CONTACT
17/51
QUINT4-PS/1AC/48DC/20
Performing high-voltage testing
If high-voltage testing of the control cabinet or the power
supply as a stand-alone component is planned during final
inspection and testing, the following features must be
observed.
– The power supply wiring must be implemented as
shown in the wiring diagram.
– The maximum permissible test voltages must not be
exceeded.
Avoid unnecessary loading or damage to the power supply
due to excessive test voltages.
For the relevant applicable test voltages and
insulation distances, refer to the corresponding
table (see technical data: electric strength of the
insulation section).
Figure 1
Disconnecting the gas discharge tube
The built-in gas discharge tube inside the device ensures
that the power supply is effectively protected against
asymmetrical disturbance variables (e.g., EN 61000-4-5).
Each surge voltage test represents a very high load for the
power supply. Therefore avoid unnecessary loading or
damage to the power supply due to excessive test voltages.
If necessary, the gas discharge tube inside the device can
be disconnected in order to use higher test voltages.
Following successful completion of testing, please
reconnect the gas-discharge tube.
Figure 2
Disconnect gas discharge tube
Potential-related wiring for the high-voltage
test
QUINT POWER Ord.No.XXXXXXX
1
2.1
+
2.2
+
2.3
–
2.4
Output DC
–
13
14
Rem
SGnd
Out 1
Out 2
t
os
Bo
%
00 Pout
1
> 5%
> 70%
> 5 OK
DC
B
–
3.1
3.2
3.3
3.4
3.5
3.6
2
HV
3
ó/=
Input AC
DC
N/- L/+
1.1 1.2 1.3
4
Key
No. Designation
Color coding
1
2
3
Blue
Blue
--
Potential levels
Potential 1
Potential 1
--
Red
Potential 2
109981_en_00
M3
x8
3.3
3.4
3.5
3.6
Signal
UOut
DC output circuit
Signal contacts
High-voltage
tester
AC input circuit
A
13
14
m
e
R d
n
SG 1
t
Ou 2
t
Ou
2.5
> 100% Boost
> 75%
> 50% POut
DC OK
4
6.3.2
QUINT POW
6.3.1
To disconnect the gas discharge tube, proceed as follows:
1. Remove power from the unit.
2. Unscrew the Phillips head screw completely and keep
the gas discharge tube screw in a safe place. The gasdischarge tube is now disconnected and is no longer
functional.
3. Perform the surge voltage test on the power supply.
4. Following successful high-voltage testing, screw the
gas discharge tube screw fully back into the power
supply.
DANGER: Risk of electric shock or damage to
the power supply due to using the wrong gas
discharge tube screw
To connect the gas-filled surge arrester, only use
the gas-filled surge arrester screw that was
originally installed in the power supply.
PHOENIX CONTACT
18/51
QUINT4-PS/1AC/48DC/20
Structure of the power supply
7.2
Figure 4
The fanless convection-cooled power supply can be
snapped onto all DIN rails according to EN 60715.
120
Function elements
Operating and indication elements
65
1
2
2.1
+
2.3
–
2.4
–
UOut
2.5
–
Signal
56V
48V
2.2
+
2.3
2.4
13
14
Rem
SGnd
Out 1
Out 2
3.1
3.2
3.3
3.4
3.5
3.6
3
2.5
UOut
56V
Signal
13
14
Rem
SGnd
Out 1
Out 2
48V
3.1
3.2
3.3
3.4
3.5
3.6
Input AC 100-240V
DC 110-250V
N/- L/+
1.1 1.2 1.3
4
Figure 5
Device dimensions (dimensions in mm)
9
2
7
5
6
2
Designation
DC output voltage connection terminal blocks
Accommodation for cable binders
Signaling connection terminal blocks
Status and diagnostics indicators
Position NFC interface (Near Field Communication)
QR code web link
AC input voltage connection terminal blocks
Gas discharge tube for surge protection (left side of
housing)
Universal DIN rail adapter (rear of housing)
Output voltage button (-) / (+)
109981_en_00
Key
Input AC 100-240V
DC 110-250V
5 N/- L/+
1.1 1.2 1.3
8
9
10
+
Output DC 48V 20A
Output DC 48V 20A
> 100% Boost
> 75% P
> 50% Out
DC OK
No.
1
2
3
4
5
6
7
8
+
> 100% Boost
> 75%
> 50% POut
DC OK
QUINT POWER Ord.No. 2904612
10
2
2.2
2.1
130
Figure 3
Device dimensions (dimensions in mm)
Ord.No. 2904612
7.1
Device dimensions
QUINT POWER
7
PHOENIX CONTACT
19/51
QUINT4-PS/1AC/48DC/20
7.3
Keep-out areas
Nominal output
capacity
a
0
5
< 50 %
≥ 50 %
Figure 6
Spacing [mm]
b
40
50
c
20
50
Device dimensions and minimum keep-out
areas (in mm)
a
a
Ord.No. 2904612
b
120
2.1
QUINT POWER
+
2.2
+
2.3
–
2.4
–
Output DC 48V 20A
UOut
130
48V
2.5
–
Signal
56V
13
14
Rem
SGnd
Out 1
Out 2
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75%
> 50% POut
DC OK
c
Input AC 100-240V
DC 110-250V
N/- L/+
1.1 1.2 1.3
109981_en_00
PHOENIX CONTACT
20/51
QUINT4-PS/1AC/48DC/20
7.4
Block diagram
Figure 7
Block diagram
Key
Symbol
Designation
Surge protection (gas discharge tube)
Symbol
Optocoupler (electrically isolating)
Surge protection (varistor) with filter
Bridge rectifier
Designation
Auxiliary converter (electrically isolating)
OVP
Additional regulatory protection against
surge voltage
Relay contact and signal contacts
Inrush current limitation
active
PFC
Power factor correction (PFC)
Switching transistor and main transmitter
(electrically isolating)
109981_en_00
μC
NFC
Microcontroller
Passive NFC interface (Near Field Communication)
Secondary rectification and smoothing
Output voltage button (-) / (+)
Filter
Signal/display LEDs (POut, DC OK)
PHOENIX CONTACT
21/51
QUINT4-PS/1AC/48DC/20
8
Mounting/removing the power
supply
8.1
Mounting the power supply unit
4.
Then separate the power supply from the DIN rail (D).
Figure 9
D
Proceed as follows to mount the power supply:
1. In the normal mounting position the power supply is
mounted on the DIN rail from above. Make sure that the
universal DIN rail adapter is in the correct position
behind the DIN rail (A).
2. Then press the power supply down until the universal
DIN rail adapter audibly latches into place (B).
3. Check that the power supply is securely attached to the
DIN rail.
Figure 8
C
A
Snapping the power supply onto the DIN rail
A
Removing the power supply from the DIN rail
8.3
B
Retrofitting the universal DIN rail adapter
For installation in horizontal terminal boxes it is possible to
mount the power supply at a 90° angle to the DIN rail.
No additional mounting material is required.
Click
8.2
B
Removing the power supply unit
Proceed as follows to remove the power supply:
1. Take a suitable screwdriver and insert this into the lock
hole on the universal DIN rail adapter (A).
2. Release the lock by lifting the screwdriver (B).
3. Carefully swivel the power supply forward (C) so that
the lock slides back into the starting position.
Use the Torx screws provided to attach the
universal DIN rail adapter to the side of the power
supply.
8.3.1
Disassembling the universal DIN rail adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
Figure 10
Disassembling the universal DIN rail adapter
8
M3x
109981_en_00
8
M3x
PHOENIX CONTACT
22/51
QUINT4-PS/1AC/48DC/20
8.3.2
Mounting the universal DIN rail adapter
To mount the universal DIN rail adapter on the left side of the
device, proceed as follows:
1. Position the universal DIN rail adapter on the left side of
the housing so that the mounting holes are congruent
with the hole pattern for the mounting holes.
2. Insert the Torx screws that were removed earlier into the
appropriate hole pattern on the universal DIN rail
adapter so that the necessary drill holes on the power
supply can be accessed.
3. Screw the universal DIN rail adapter onto the power
supply.
The maximum tightening torque of the Torx screw
(Torx® T10) is 0.7 Nm.
Figure 11
Mounting the universal DIN rail adapter
8.4.1
Mounting the UWA 182/52 universal wall
adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter in such a way that
the keyholes or oval tapers face up. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes on the power supply can be accessed.
6. Screw the universal wall adapter onto the power supply.
Figure 12
x8
M3
Mounting the UWA 182/52 universal wall
adapter
x8
M3
M3x
8.4
8
M3x
8
Retrofitting the universal wall adapter
The UWA 182/52 universal wall adapter (Item No. 2938235)
or UWA 130 universal wall adapter (Item No. 2901664) is
used to attach the power supply directly to the mounting
surface.
The use of universal wall adapters is recommended under
extreme ambient conditions, e.g., strong vibrations. Thanks
to the tight screw connection between the power supply and
the universal wall adapter or the actual mounting surface, an
extremely high level of mechanical stability is ensured.
The maximum tightening torque of the Torx screw
(Torx® T10) is 0.7 Nm.
Make sure you use suitable mounting material
when attaching to the mounting surface.
The power supply is attached to the UWA 182 or
UWA 130 universal wall adapter by means of the
Torx screws of the universal DIN rail adapter.
109981_en_00
PHOENIX CONTACT
23/51
QUINT4-PS/1AC/48DC/20
8.4.2
Mounting the UWA 130 2-piece universal wall
adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes in the side flanges of the power supply
can be accessed.
6. Screw the two-piece universal wall adapter onto the
power supply.
Fix connection wiring to the power supply
Two receptacles for the bundled attachment of the
connection wiring are integrated in the left and right housing
panel. Use cable binders to secure the connection wiring
(optional WT-HF 3,6X140 - Item No. 3240744).
Proceed as follows to secure the connection wiring:
– Wire the power supply with sufficient connection
reserve (input terminal blocks, output terminal blocks,
signal terminal blocks)
– Bundle and set up the connection wiring so that the
cooling grilles on the top and bottom of the housing are
covered as little as possible.
– Thread the cable binders into the necessary
receptacles for the cable binders.
Figure 14
Lay and align connection wiring
Mounting the UWA 130 universal wall adapter
QUINT POWER
Ord.No.29046xx
Figure 13
8.5
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
na
l
>1
> 7 00%
> 55% Boo
st
0
D %
M3x
CO
8
M3x
K
8
–
3.1
3.2
3.3
3.4
3.5
3.6
Po
ut
Secure the connection wiring with the cable binders.
Make sure that the connection wiring is attached safely
and securely without damaging the connection wiring.
QUINT POWER
Ord.No.29046xx
Figure 15
Secure connection wiring with cable binder
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
na
l
>1
> 7 00%
> 55% Boo
st
D 0%
3.1
3.2
3.3
3.4
3.5
3.6
C O Po
ut
K
109981_en_00
PHOENIX CONTACT
24/51
QUINT4-PS/1AC/48DC/20
–
–
Shorten the excess length of the cable ties.
Then check again that the connection wiring is properly
secured.
Figure 16
Shorten protruding ends of the cable binder
9
Device connection terminal blocks
The AC input and DC output terminal blocks on the front of
the power supply feature screw connection technology. The
signal level is wired without tools by means of Push-in
connection technology.
QUINT POWER
Ord.No.29046xx
For the necessary connection parameters for the
connection terminal blocks, refer to the technical
data section.
9.1
2.1
+ 2.2
+ 2.3
Ou - 2.4
tpu - 2.5
tD
C -
U
Out
13
14
Re
m
SG
nd
Ou
t1
Ou
t2
Sig
na
l
>1
> 7 00%
> 55% Boo
st
D 0%
3.1
3.2
3.3
3.4
3.5
3.6
C O Po
ut
K
NOTE: Mechanical damage to the connection
wiring caused by friction
In extreme ambient conditions, e.g., strong
vibrations, protect the connection wiring against
mechanical damage using additional insulation
material. The additional insulation material for
protecting the connection wiring is limited to the
area where the cable binders are attached.
Input
The power supply is operated on single-phase AC systems
or two outer conductors of three-phase systems. The power
supply is connected on the primary side via the INPUT L/N/
connection terminal blocks.
The power supply is approved for connection to
TN, TT, and IT power grids with a maximum
phase-to-phase voltage of 240 V AC.
Figure 17
Network types
TN-S
TN-C
L
N
PE
N L
L
PEN
N L
+ ̐
+ ̐
L1
L2
L3
N
PE
N L
L1
L2
L3
PEN
N L
+ ̐
TT
+ ̐
iT
L
N
L
PEN
N L
N L
+ ̐
+ ̐
L1
L2
L3
L1
L2
L3
N
N L
109981_en_00
+ ̐
N L
+ ̐
PHOENIX CONTACT
25/51
QUINT4-PS/1AC/48DC/20
9.2
Protection of the primary side
Installation of the device must correspond to EN 61010
regulations. It must be possible to switch off the device using
a suitable disconnecting device outside the power supply.
The line protection on the primary side is suitable for this
(see technical data section).
DANGER: Hazardous voltage
An all-pos. fuse must be present for operation on
two outer conductors of a three-phase system.
Protection for AC supply
Figure 18
Pin assignment for AC supply voltage
9.3
Output
By default, the power supply is pre-set to a nominal output
voltage of 48 V DC.
The output voltage is adjusted via the two arrow keys (-)
and (+) on the front of the power supply.
When you press the arrow key once briefly, the output
voltage is reduced (-) or increased (+) by 3 mV. When you
press the arrow key for longer, the voltage is adjusted in
100 mV increments.
9.4
Protection of the secondary side
The power supply is electronically short-circuit-proof and
no-load-proof. In the event of an error, the output voltage is
limited
Input AC 100...240 V
L
If sufficiently long connecting cables are used,
fuse protection does not have to be provided for
each individual load.
L
N
PE
N
PE
N/-
L/+
If each load is protected separately with its own
protective device, the selective shutdown in the
event of a fault enables the system to remain
operational.
Protection for DC supply
Figure 19
Pin assignment for DC supply voltage
Input DC 110...250 V
+
+
-
-
PE
N/-
L/+
DC applications require upstream installation of a fuse that
is permitted for the operating voltage.
109981_en_00
PHOENIX CONTACT
26/51
QUINT4-PS/1AC/48DC/20
10
Output characteristic curves
This section describes the various output characteristic curves together with their areas of application for customization to
your specific application. The U/I Advanced characteristic curve is set by default.
M
Application
Normal load
Your benefits
Reliable power supply
System extension
+
-
Loads with high inrush
Energy storage charging
current
A stable 24 V, even in the No over-dimensioned
power supply unit
event of a sustained
required
overload
Fast charging
Selective tripping of
fuses
Keeps temperatures
low in the event of
faults
Short circuit, non-fused
Parallel loads continue
working
Low thermal stress in
the even of faults
Enables configuration
without fuse
Characteristics
-
U/I Advanced
-
Smart HICCUP
-
FUSE MODE
Symbol
-
-
-
Designation
Suitable for the application
-
109981_en_00
Not suitable for the application
PHOENIX CONTACT
27/51
QUINT4-PS/1AC/48DC/20
U/I Advanced output characteristic curve
The preset U/I Advanced output characteristic curve is
optimized for the following applications:
– For selective tripping of standard circuit breakers (SFB
technology). The power supply supplies up to 6 times
the nominal current for 15 ms. Loads connected in
parallel continue working.
– When supplying loads with high switch-on currents,
such as motors. The dynamic boost of the power supply
supplies up to 200% of the nominal power for 5 s. This
ensures that sufficient reserve energy is available;
overdimensioning of the power supply is not necessary.
– For system extension. With the static boost, up to
125% of the nominal output power is available for a
sustained period (up to 40°C).
– For fast energy storage charging (e.g., of batteries) to
supply a wide range of loads. The power supply
operates in the nominal operating range. Energy supply
to the load is ensured.
Figure 20
10.2
Smart HICCUP output characteristic curve
The SMART HICCUP output characteristic curve keeps the
thermal load of the connecting cables at a low level in the
event of a sustained overload. If loads are not protected or
are protected in a way that is not permitted, the loads are
supplied for 2 s. The DC output of the power supply is then
switched off for 8 s. This procedure is repeated until the
cause of the overload has been remedied.
The Smart HICCUP output characteristic curve is optimized
for the following applications:
– If only a low short-circuit current is permitted.
– If following an overload or short circuit the output
voltage should be made available again automatically.
Figure 21
10.1
Smart HICCUP output characteristic curve
U/I Advanced output characteristic curve
109981_en_00
PHOENIX CONTACT
28/51
QUINT4-PS/1AC/48DC/20
10.3
FUSE MODE output characteristic curve
In the event of an overload (e.g., short circuit), the power
supply switches off the DC output permanently. The value of
the switch-off threshold and the time period for which it may
be exceeded can be freely selected. The power supply is
restarted via the remote contact. As an option, the power
supply can be switched on by switching the supply voltage
on the primary side off and on.
Selecting the FUSE MODE output characteristic curve sets
the following default values.
– tFuse = 100 ms
– IFuse = IN
FUSE MODE output characteristic curve
IOut [A]
Figure 22
IFuse
0
tFuse
t [s]
109981_en_00
PHOENIX CONTACT
29/51
QUINT4-PS/1AC/48DC/20
Configuring the power supply
With the fourth generation of the QUINT POWER power
supply, it is now possible for the first time to adapt the
behavior of the power supply. In addition to setting the
output voltage and selecting the output characteristic
curves, you can configure signal outputs Out 1, Out 2, and
floating signal contact 13/14, for example. Configuration of
the remote input for controlling the power supply or
specification of signal options and signal thresholds also
extend the range of possible applications.
The power supply is configured via the device's internal NFC
(near field communication) interface. This is located behind
the QR code on the front.
11.2
To configure the power supply, proceed as follows:
– Before you can configure the power supply, it should
either be disconnected from the supply voltage or
switched to SLEEP MODE.
– To switch the power supply to SLEEP MODE, use one
of the external circuits. The following connection
versions are possible between the Rem (remote input)
and SGnd (signal ground) connection terminal blocks.
Figure 23
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– PC or notebook (as of Windows 7, Microsoft.Net
Framework 4.5, USB 2.0 interface, 50 MB hard disk
capacity, QUINT POWER software).
– Programming adapter:
TWN4 MIFARE NFC USB ADAPTER (Item No.
2909681) is plugged into the USB interface.
– Programming software: the QUINT POWER software
has been successfully installed.
–
Hold the USB-PROG-ADAPTER in front of the mounted
power supply such that the NFC antenna symbol is over
the QR code.
Figure 24
Configuration of the power supply
QUINT POWER Ord.No.29046xx
Configuration with PC software
SLEEP MODE connection versions
The power supply behaves like a passive NFC tag.
An auxiliary power source is required in order to
supply the power supply with configuration data.
11.1
Configuring the power supply
13
14
Rem
nd
SG 1
t
Ou 2
t
Ou
l
na
3.1
3.2
3.3
3.4
3.5
3.6
ost
Bo
% t
00
> 15% Pou
> 70%
> 5 OK
DC
x8
CONN
DAT
M3
Sig
UOut
NFC
11
–
In the programming interface of the QUINT POWER
software, press the [Read] button. The current device
and configuration data for the power supply is read and
displayed.
If a connection cannot be established between the
USB-PROG-ADAPTER and the power supply,
more detailed information can be found in the user
manual for the QUINT POWER software.
For information regarding the configuration of the
power supply, such as selecting the characteristic
curve and output parameters, refer to the user
manual for the QUINT POWER software.
109981_en_00
PHOENIX CONTACT
30/51
QUINT4-PS/1AC/48DC/20
Configuration with NFC-capable mobile
terminal device
The QUINT POWER app enables you to conveniently
configure the power supply using a mobile terminal device,
such as a smartphone.
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– NFC-capable mobile terminal device with Android
operating system as of Version 4.1.x (Jelly Bean)
– QUINT POWER app (Google Play Store)
For information regarding the configuration of the
power supply, such as selecting the characteristic
curve and output parameters, please refer to the
QUINT POWER app.
11.4
Boost currents
The power supply provides the static boost (IStat. Boost) for a
sustained load supply or the time-limited dynamic boost
(IDyn. Boost).
12.1
Static Boost
For system expansion purposes, the sustained static boost
(IStat. Boost) supports the load supply with up to 112% of the
nominal current of the power supply. The static boost is
available at an ambient temperature of up to 40°C.
Figure 25
11.3
12
Performance characteristic in static boost
Ordering a configured power supply
Customer-specified QUINT POWER power supplies are
ordered as a KMAT item (configurable material) and are
configured during the production process in the factory. The
power supply is therefore supplied ready to connect for your
specific application.
You can type in the the web code
phoenixcontact.net/webcode/#0852
to configure and order your power supply.
12.2
Dynamic Boost
Dynamic boost (IDyn. Boost) delivers up to 150 % of the power
supply nominal current to supply high loads. This temporary
power supply to the load lasts a maximum of 5 s at an
ambient temperature of up to 60 °C. The energy supplied
adaptively for the load supply and the recovery time (tPause)
are calculated based on the specific load situation using
algorithms (see recovery time tables).
IOut [A]
Figure 26
IDyn.Boost
IBase Load
Basic curve of the dynamic boost process
tDyn.Boost
tDyn.Boost
tPause
t [s]
109981_en_00
PHOENIX CONTACT
31/51
QUINT4-PS/1AC/48DC/20
If a current that is lower than the maximum
available dynamic boost current (IDyn. Boost) is
required for the same period, the recovery time
may (tPause) decrease.
12.2.1 Recovery times at an ambient temperature of
40 °C
Required recovery times at ≤ 40°C
tDyn. Boost [s]
IBase Load
IDyn. Boost
[A]
[A]
1
2
3
4
5
0
30
1,3
2,5
3,8
5,1
6,4
5
30
1,3
2,7
4,0
5,4
6,7
10
30
1,5
2,9
4,4
5,9
7,4
15
30
1,7
3,5
5,2
7,0
8,7
20
30
2,8
5,6
8,4
11,2
14,0
22,5
30
7,0
14,0
20,9
27,9
34,9
At an output current (IBase Load) of 10 A, the dynamic output
current (IDyn. Boost) of 30 A increases for 2 s (tDyn. Boost).
After a recovery time (tPause) of 2.9 s, the dynamic boost is
available once again.
Figure 29
Example recovery time for ≤ 40°C
tDyn. Boost [s]
IBase Load
IDyn. Boost
[A]
[A]
1
2
3
4
5
0
30
1,3
2,5
3,8
5,1
6,4
5
30
1,3
2,7
4,0
5,4
6,7
10
30
1,5
2,9
4,4
5,9
7,4
15
30
1,7
3,5
5,2
7,0
8,7
20
30
2,8
5,6
8,4
11,2
14,0
22,5
30
7,0
14,0
20,9
27,9
34,9
tPause [s]
Figure 27
12.2.3 Example: Determining the recovery time
(tPause)
tPause [s]
Use the following tables to determine the required recovery
time (tPause) at the maximum dynamic boost current (IDyn.
Boost) based on the following values:
– IBase Load
– Duration of the boost current (tDyn. Boost)
– Ambient temperature (40 °C or 60 °C)
12.2.2 Recovery times at an ambient temperature of
60 °C
Required recovery times at ≤ 60°C
tDyn. Boost [s]
IBase Load
IDyn. Boost
[A]
[A]
1
2
3
4
5
0
30
1,6
3,3
5,0
6,7
8,3
5
30
1,8
3,6
5,4
7,2
9,1
10
30
2,1
4,3
6,4
8,5
10,6
15
30
2,6
4,3
7,9
10,6
13,2
20
30
11,0
22,1
33,1
44,2
55,2
109981_en_00
tPause [s]
Figure 28
PHOENIX CONTACT
32/51
QUINT4-PS/1AC/48DC/20
13
SFB Technology
13.3
SFB Technology (selective fuse breaking) can be used to
quickly and reliably trip miniature circuit breakers and fuses
connected on the secondary side. In the event of a short
circuit on the secondary side, the power supply supplies up
to 6 times the nominal current for 15 ms. The faulty current
path is switched off selectively.
Loads that are connected in parallel are still supplied with
energy. Operation of these system parts is ensured. In order
to always enable the reliable tripping of circuit breakers and
fuses, certain framework conditions must be observed (see
SFB configuration section).
Observe the following framework conditions for determining
the maximum distance between the power supply and load:
– The performance class of the power supply
– The cross section of the connecting cable
– The tripping characteristic of the fuse component
Figure 31
Schematic diagram of the maximum cable
length
Power supply unit
+
+
-
-
Load
l
The U/I Advanced output characteristic curve
supports SFB Technology.
13.1
SFB configuration
Tripping circuit breakers
The circuit breaker is tripped by the high SFB current of the
power supply, typically within 3 to 5 ms. As a result, voltage
dips at loads that are connected in parallel are avoided.
I [A]
Figure 30
SFB pulse trips circuit breakers
6x IN
typ. 3 - 5 ms
IN
0
13.2
t [s]
Tripping a fuse
Fuses are tripped by melting the predetermined breaking
point inside the fuse capsule. The tripping characteristic of
the fuse is described by the melting integral (I²t). A high
current is crucial in order to achieve a very short tripping
time.
109981_en_00
PHOENIX CONTACT
33/51
QUINT4-PS/1AC/48DC/20
13.4
Maximum distance between the power supply and load
The distances given in the table are worst-case values and therefore cover the entire tolerance range for the magnetic tripping
of circuit breakers. The possible distances are often greater in practice.
13.4.1 Thermomagnetic device circuit breaker, type: Phoenix Contact CB TM1 SFB
Maximum distance l [m] with device circuit
breaker
Phoenix Contact
CB TM1 1A SFB P
CB TM1 2A SFB P
CB TM1 3A SFB P
CB TM1 4A SFB P
CB TM1 5A SFB P
CB TM1 6A SFB P
CB TM1 8A SFB P
CB TM1 10A SFB P
CB TM1 12A SFB P
CB TM1 16A SFB P
Conductor cross section
A [mm²]
AWG
0.75
19
77
44
30
23
16
11
6
4
3
1
1.0
18
75%
POut
> 50%
DC OK
1
2
3
4
5
Key
No.
1
2
3
4
5
6
7
8
9
109981_en_00
Position of signaling elements
UOut
56V
The current device status of the power supply is signaled
using four LED status indicators. The function of each LED
status indicator is assigned to a fixed event.
The signal outputs are configured on the software side using
the QUINT POWER software or the QUINT POWER app.
Upon delivery, the power supply is pre-allocated a default
configuration for the signal outputs.
Location and function of the signaling elements
Signaling elements
13/14 floating switch contact (N/O contact)
Rem, remote input (switch power supply off and on)
SGnd, signal ground (reference potential for signals
Out 1, Out 2)
Out 1 (digital output, function depends on the signal
option set)
Out 2 (digital or analog output, function depends on
the signal option set)
LED status indicator DC OK
LED on: UOut > 90% x USet
LED flashing: UOut 50 % (output power
>480 W)
LED status indicator POut >75 % (output power
>720 W)
LED status indicator POut >100 %, boost mode (output power >960 W)
PHOENIX CONTACT
38/51
QUINT4-PS/1AC/48DC/20
14.1.1 Floating signal contact
In the default configuration, the floating switch contact
opens to indicate that the set output voltage has been
undershot by more than 10 % (UOut 75% LED lights up green in addition
to the > 50% LED. If the required output power is then
greater than the nominal device power, the power supply
operates in boost mode. In boost mode, the > 100% LED
additionally lights up yellow.
109981_en_00
Four LED status indicators are integrated in the front of the
power supply, which indicate the current device state.
External wiring versions with PNP and NPN
output
14.5
Figure 38
When using a PLC output, select the following external
circuit version to switch the power supply to SLEEP MODE.
PHOENIX CONTACT
42/51
QUINT4-PS/1AC/48DC/20
14.6
U/I Advanced characteristic curve signaling
The following table shows the standard assignment for signaling for the U/I Advanced characteristic curves which is set by
default.
Figure 39
Signal image for U/I Advanced
LED: POut >100 %
yellow
Signal Out 2: POut < PN
Default
Normal operation
BOOST
Overload operation
POut < PN
POut > PN
UOut < 0.9 x USet
Active High
Active Low
Active Low
closed
closed
open
Active High
Active High
Active Low
LED: POut > 75 %
LED: POut > 50 %
green
LED: DC OK
Relay: 13/14, DC OK
Default
Signal Out 1: DC OK
LED off
14.7
LED on
LED flashing
Smart HICCUP characteristic curve signaling
The following table shows the standard assignment for signaling for the Smart HICCUP characteristic curve.
Figure 40
Signal image for Smart HICCUP
LED: POut >100 %
Signal Out 2: POut < PN
Normal operation
BOOST
Overload operation
POut < PN
POut > PN
UOut < 0.9 x USet
Active High
Active Low
Active Low
Yellow
Default
LED: POut > 75 %
LED: POut > 50 %
Green
LED: DC OK
Closed
Relay: 13/14, DC OK
Closed
Open
Default
Signal Out 1: DC OK
Active High
LED off
109981_en_00
LED on
Active High
Active Low
LED flashing
PHOENIX CONTACT
43/51
QUINT4-PS/1AC/48DC/20
14.8
FUSE MODE characteristic curve signaling
The following table shows the standard assignment for signaling for the FUSE MODE characteristic curve.
Figure 41
Signal image for FUSE MODE
LED: POut >100 %
Yellow
Signal Out 2: POut < PN
Default
Normal operation
BOOST
POut < PN
POut > PN
Active High
Active Low
Active Low
Closed
Closed
Open
Active High
Active High
Active Low
FUSE MODE
I > IFuse
for t > tFuse
LED: POut > 75 %
LED: POut > 50 %
Green
LED: DC OK
Relay: 13/14, DC OK
Default
Signal Out 1: DC OK
LED off
14.9
LED on
LED flashing
SLEEP MODE signaling
In SLEEP MODE, all LEDs are off, all signals are low, and the relay switching contact is open.
109981_en_00
PHOENIX CONTACT
44/51
QUINT4-PS/1AC/48DC/20
14.10 Special immunity for the signal level
14.10.1 Surge protection for the high-voltage area at the power plant
Surge protection (Phoenix Contact Item No.: 2907925 or comparable protection) must be implemented for power plant
applications when using signal connection types t (telecommunications area), h (high voltage area) or f (field) in accordance
with IEC/EN 61850-3 or signal connection types 3 (process area) and 4 (high voltage area) in accordance with EN 61000-6-5.
When using the digital signals, a relay (Phoenix Contact Item No.: 2900299 or a comparable relay) can be implemented.
14.10.2 Surge protection for signals in railway applications
Surge protection (Phoenix Contact Item No.: 2907925 or comparable protection) must be implemented for railway
applications when using signals in accordance with EN 62236-4 and EN 50121-4.
When using the digital signals, a relay (Phoenix Contact Item No.: 2900299 or a comparable relay) can be implemented.
14.10.3 Surge protection for devices in use in safety-related systems
Surge protection (Phoenix Contact Item No.: 2907925 or comparable protection) must be implemented for railway
applications when using signals in accordance with EN 61000-6-7 for devices provided to perform functions in safety-related
systems (functional safety) in industrial settings.
When using the digital signals, a relay (Phoenix Contact Item No.: 2900299 or a comparable relay) can be implemented.
Figure 42
Schematic diagram, signal wiring with TRABTECH surge protection
!
"
"
"
"
"
"#
Figure 43
Schematic diagram, signal wiring with relay module
!
109981_en_00
"
"
"
"
"
"#
PHOENIX CONTACT
45/51
QUINT4-PS/1AC/48DC/20
15
Operating modes
15.1
Series operation
15.2
To double the output voltage, connect two power supplies in
series. Only use power supplies with the same performance
class and configuration for series operation. If two 48 V DC
power supplies are connected in series, an output voltage of
96 V DC is available to supply the loads.
Figure 44
Parallel operation
You can connect several power supplies in parallel in order
to increase the power or to supply the loads redundantly.
Figure 45
Schematic diagram in parallel operation
IN
IN
+ ̐
+ ̐
Schematic diagrams in series operation
+
+
-
-
+
̐
+
+48 V
-
+96 V
-96 V
+
+
-
-
-48 V
+
-
+ ̐
Ǟ = IN
Observe the following points when carrying out parallel
connection:
1. Use power supplies of the same type and performance
class
2. Setting the same output voltages
3. Using the same cable cross sections for wiring
4. Using the same cable lengths for the DC convergence
point
5. Operating power supplies in the same temperature
environment
6. When three or more power supplies are connected in
parallel, each output must be protected (e.g., with
circuit breakers, fuses or decoupling modules)
We recommend the configuration "parallel
operation" for a parallel connection.
For more detailed information on the operating
mode for parallel operation, refer to the user
manual for the QUINT POWER software or the
QUINT POWER app.
109981_en_00
PHOENIX CONTACT
46/51
QUINT4-PS/1AC/48DC/20
15.2.1 Redundancy operation
Redundant circuits are suitable for supplying systems and
system parts which place particularly high demands on
operational reliability.
If energy is to be supplied to the load with 1+1 redundancy,
two power supplies of the same type and performance class
must be used. In the event of an error, it must be ensured
that one of the power supplies is able to provide the total
required power for the load. This means that in redundancy
mode, two 20 A power supplies supply a load with a nominal
current of 20 A, for example. During normal operation of the
power supplies, each power supply therefore supplies 10 A.
15.2.2 Increased power
When n power supplies are connected in parallel, the output
current is increased to n x IN. Parallel connection for
increased power is used when extending existing systems.
If the individual power supply does not cover the current
consumption of the most powerful load, parallel connection
of power supplies is recommended.
When three or more power supplies are
connected in parallel, each output must be
protected separately, e.g., by a circuit breaker,
fuse or decoupling module such as
QUINT ORING, QUINT S-ORING or
QUINT DIODE.
Always use cables with the same cross sections and lengths
when wiring the power supplies on the DC output side.
Redundancy modules can be used to fully decouple two
power supplies from one another and to ensure the supply.
Optimum decoupling can be achieved with the
QUINT DIODE redundancy module.
Figure 46
Figure 47
IN
IN
+ ̐
+ ̐
+
̐
IN
+ –
Schematic diagram, redundant operation with
QUINT DIODE
IN
Schematic diagram of increased performance
+ –
+
–
+ –
+ ̐
IǞ= 2 x IN
Ǟ = IN
Certain specifications apply in redundancy operation with
regard to the configuration of the keepout areas. In
redundancy operation, the power supplies are operated with
maximum half the nominal power. The keepout areas are
therefore reduced.
Using the signaling settings, you can monitor whether both
power supplies are being operated with ≤ half the nominal
load. In the case of system extension, an overload is
prevented if one of the power supplies fails.
109981_en_00
PHOENIX CONTACT
47/51
QUINT4-PS/1AC/48DC/20
Derating
16.3
The QUINT POWER power supply runs in nominal
operation without any limitations. For operation outside the
nominal range, the following points should be observed
depending on the type of use.
16.1
Ambient temperature
When operating the power supply at an ambient
temperature of > 60 °C, a power derating of 2.5 %/K should
be observed. Up to an ambient temperature of 40 °C, the
power supply can take power from the static boost for a
sustained period. In the 40 °C to 60 °C temperature range,
the power supply can output more than the nominal power
for a sustained period.
Figure 48
Output power depending on the ambient
temperature
Installation height
The power supply can be operated at an installation height
of up to 2000 m without any limitations. Different data
applies for installation locations above 2000 m due to the
differing air pressure and the reduced convection cooling
associated with this (see technical data section). The data
provided is based on the results of pressure chamber testing
performed by an accredited test laboratory.
Figure 49
POut [%]
16
Output power depending on the installation
height
175
ĵ
150
125
Ĵ
100
75
25
0
ij
ij = PN 100 % ç 60 °C
Ĵ = PStat.112 % ç 40 °C
ĵ = PDyn. 150 % ç 60 °C
50
0
1000
2000
3000
4000
5000
H [m]
16.2
Input voltage
UIn
< 100 V AC
< 110 V DC
< 115 V AC
< 110 V DC
109981_en_00
Derating 1 %/V
TA
IOut
≤ 60 °C
IN
≤ 40 °C
IStat. Boost
UOut
48 V DC
PHOENIX CONTACT
48/51
QUINT4-PS/1AC/48DC/20
16.4
Position-dependent derating
The fanless convection-cooled power supply can be snapped onto all DIN rails according to EN 60715.
The power supply should be mounted horizontally for heat dissipation reasons (AC connection terminal blocks
facing downward). Please observe the derating for any mounting other than the normal mounting position. Reduce
the output power based on the prevailing ambient temperature.
The recommended output power for different mounting positions and ambient temperatures can be found in the
characteristic curves below.
Exceeding these values will reduce the service life of the power supply.
'()*+,
-#%) %$. &//
0 2
16.4.1 Normal mounting position
!
"
#
$
%
%$
%
%
%
%&
012
Pout [%]
16.4.2 Rotated mounting position 90° Z-axis
175
ĵ
150
Ĵ
125
100
75
M
3x
8
50
25
INT
UOut
Signal
13
3.1
14
3.2
Rem
3.3
SGnd
3.4
Out 1
3.5
Out 2
3.6
> 100% Boost
> 75% P
out
> 50%
DC OK
Y
QU
POW
ER
Ord
.No.
2904
6xx
ij = PN 100 %
Ĵ = PStat.112 %
ĵ = PDyn. 150 %
0
-25 0
10
20
ij
30
40
50
60
70
80
ă [°C]
Z
X
109981_en_00
PHOENIX CONTACT
49/51
QUINT4-PS/1AC/48DC/20
&
0 2
16.4.3 Rotated mounting position 180° Z-axis
%!
%
!!
"#
&
$
%
'
(
)*
+
&
&
%
%
%%
%
/
+.
),-
&
01#2
Pout [%]
16.4.4 Rotated mounting position 270° Z-axis
175
ĵ
150
Ĵ
125
100
3.1
3.2
3.3
3.4
3.5
3.6
50
> 100% Boost
> 75%
> 50% Pout
DC OK
OW
E
o.2
9
x
6x
04
UOut
13
14
Rem
SGnd
Out 1
Out 2
INT
P
rd.N
RO
Y
QU
Signal
75
25
ij = PN 100 %
Ĵ = PStat.112 %
ĵ = PDyn. 150 %
0
-25 0
10
20
ij
30
40
50
60
70
80
ă [°C]
Z
X
109981_en_00
PHOENIX CONTACT
50/51
QUINT4-PS/1AC/48DC/20
'
()
*
+
,
-
!
)
!
.
"
//
16.4.5 Rotated mounting position 90° X-axis
#$
"
!
!
!
!
!
0 2
&
% !
012
Pout [%]
16.4.6 Rotated mounting position 270° X-axis
175
ĵ
150
Ĵ
125
100
75
50
25
ij = PN 100 %
Ĵ = PStat.112 %
ĵ = PDyn. 150 %
0
-25 0
10
20
ij
30
Y
40
50
60
70
80
ă [°C]
Z
X
109981_en_00
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
phoenixcontact.com
51/51
工商网监
湘ICP备2023018690号
