2909524

https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) PLC-INTERFACE, consisting of DIN-rail-mountable basic terminal block in 6.2 mm with screw connection and plug-in miniature relay with 6 A power contact, 1 changeover contact, 24 V DC input voltage. Approved according to ATEX/IECEx (Zone 2) and Ex Zone Class I, Div. 2. Key Commercial Data Packing unit 1 pc Minimum order quantity 10 pc GTIN GTIN 4055626363615 Weight per Piece (excluding packing) 42.000 g Custom tariff number 85364190 Country of origin Germany Technical data Note Utilization restriction EMC: class A product, see manufacturer's declaration in the download area Dimensions Width 6.2 mm Height 80 mm Depth 94 mm Ambient conditions Ambient temperature (operation) -20 °C ... 60 °C (UL) -40 °C ... 60 °C (ATEX / IECEx) Ambient temperature (storage/transport) -40 °C ... 85 °C 05/07/2020   Page 1 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Technical data Ambient conditions Degree of protection RT III (Relay) IP20 (Relay base) Coil side Nominal input voltage UN 24 V DC Typical input current at UN 9 mA Typical response time 5 ms Typical release time 8 ms Protective circuit Reverse polarity protection Polarity protection diode Free-wheeling diode Damping diode Operating voltage display Yellow LED Power dissipation for nominal condition 0.22 W Contact side Contact type 1 PDT Type of switch contact Single contact Contact material AgSnO Maximum switching voltage 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) Minimum switching voltage 5 V (at 100 mA) Min. switching current 10 mA (at 12 V) Maximum inrush current 10 A (4 s) Limiting continuous current 6A Interrupting rating (ohmic load) max. 140 W (at 24 V DC) 20 W (at 48 V DC) 18 W (at 60 V DC) 23 W (at 110 V DC) 40 W (at 220 V DC) 1500 VA (for 250 V AC) Switching capacity 2 A (at 24 V, DC13) 0.2 A (at 110 V, DC13) 0.1 A (at 220 V, DC13) 3 A (at 24 V, AC15) 3 A (at 120 V, AC15) 3 A (at 230 V, AC15) General Test voltage relay winding/relay contact 4 kV AC (50 Hz, 1 min.) 05/07/2020   Page 2 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Technical data General Operating mode 100% operating factor Flammability rating according to UL 94 V0 (Housing) Mechanical service life 2x 10 cycles Mounting position any Assembly instructions In rows with zero spacing 7 Connection data Connection name Coil side Connection method Screw connection Stripping length 8 mm Screw thread M3 Conductor cross section solid 0.14 mm² ... 2.5 mm² Conductor cross section flexible 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG 26 ... 14 Connection data 2 Connection name Contact side Connection method Screw connection Stripping length 8 mm Screw thread M3 Conductor cross section solid 0.14 mm² ... 2.5 mm² Conductor cross section flexible 0.14 mm² ... 2.5 mm² 0.2 mm² ... 2.5 mm² (Single ferrule) 2x 0.5 mm² ... 1.5 mm² (TWIN ferrule) Conductor cross section AWG 26 ... 14 Standards and Regulations Designation Standards/regulations Standards/regulations IEC 60664 EN 50178 EN 60079-0, -7, -15 Pollution degree 3 Overvoltage category III Conformance CE-compliant ATEX  II 3G Ex ec nC IIC T4 Gc IECEx Ex ec nC IIC T4 Gc UL, USA Class I, Zone 2, AEx nA nC IIC T6 05/07/2020   Page 3 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Technical data Standards and Regulations UL, USA/Canada Class I, Div. 2, Groups A, B, C, D UL, Canada Class I, Zone 2, Ex nA nC IIC Gc T6 X Conformance/approvals Designation CE Identification CE-compliant Designation ATEX Identification  II 3G Ex ec nC IIC T4 Gc Certificate IBExU16ATEXB015 X Designation IECEx Identification Ex ec nC IIC T4 Gc Certificate IECEx IBE 16.0029X Designation UL, USA Identification Class I, Zone 2, AEx nA nC IIC T6 Designation UL, USA/Canada Identification Class I, Div. 2, Groups A, B, C, D Designation UL, Canada Identification Class I, Zone 2, Ex nA nC IIC Gc T6 X Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings 05/07/2020   Page 4 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Diagram Curve A Maximum permissible continuous voltage Umax with limiting continuous current on the contact side (see relevant technical data) Curve B Minimum permissible operate voltage Uop after pre-excitation (see relevant technical data) 05/07/2020   Page 5 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Diagram Interrupting rating 05/07/2020   Page 6 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Circuit diagram Classifications eCl@ss eCl@ss 5.0 27371600 eCl@ss 5.1 27371600 eCl@ss 6.0 27371600 eCl@ss 7.0 27371601 eCl@ss 8.0 27371601 eCl@ss 9.0 27371601 ETIM ETIM 2.0 EC001437 ETIM 3.0 EC001437 ETIM 4.0 EC001437 05/07/2020   Page 7 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Classifications ETIM ETIM 5.0 EC001437 ETIM 6.0 EC001437 ETIM 7.0 EC001437 UNSPSC UNSPSC 6.01 30211916 UNSPSC 7.0901 39121515 UNSPSC 11 39121515 UNSPSC 12.01 39121515 UNSPSC 13.2 39122334 UNSPSC 18.0 39122334 UNSPSC 19.0 39122334 UNSPSC 20.0 39122334 UNSPSC 21.0 39122334 Approvals Approvals Approvals DNV GL Ex Approvals IECEx / ATEX / UL Listed / cUL Listed / KC-s / EAC Ex / cULus Listed Approval details DNV GL    https://approvalfinder.dnvgl.com/  TAE0000196-03 Accessories Accessories Bridge 05/07/2020   Page 8 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories Continuous plug-in bridge - FBST 500-PLC RD - 2966786 Continuous plug-in bridge, length: 500 mm, color: red     Continuous plug-in bridge - FBST 500-PLC BU - 2966692 Continuous plug-in bridge, length: 500 mm, color: blue     Continuous plug-in bridge - FBST 500-PLC GY - 2966838 Continuous plug-in bridge, length: 500 mm, color: gray     Single plug-in bridge - FBST 6-PLC RD - 2966236 Single plug-in bridge, length: 6 mm, number of positions: 2, color: red     Single plug-in bridge - FBST 6-PLC BU - 2966812 Single plug-in bridge, length: 6 mm, number of positions: 2, color: blue     05/07/2020   Page 9 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories Single plug-in bridge - FBST 6-PLC GY - 2966825 Single plug-in bridge, length: 6 mm, number of positions: 2, color: gray     Single plug-in bridge - FBST 8-PLC GY - 2967688 Single plug-in bridge, length: 8 mm, number of positions: 2, color: gray     Controller board System connection - PLC-V8/FLK14/OUT - 2295554 V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw connection 1x, connection 2: IDC/FLK pin strip 1x 14-position, connection 3: Plug connection (Can be snapped onto 8x PLC-INTERFACE terminals), number of channels: 8, control logic: positive switching     System connection - PLC-V8/FLK14/OUT/M - 2304102 V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw connection 1x, connection 2: IDC/FLK pin strip 1x 14-position, connection 3: Plug connection (Can be snapped onto 8x PLC-INTERFACE terminals), number of channels: 8, control logic: negative switching     Adapter module - PLC-V8/D15S/OUT - 2296058 V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw connection 1x, connection 2: D-SUB pin strip 1x 15-position, connection 3: Plug connection (Can be snapped onto 8x PLC-INTERFACE terminals), number of channels: 8, control logic: positive switching     05/07/2020   Page 10 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories System connection - PLC-V8/D15B/OUT - 2296061 V8 adapter for 8 x PLC-INTERFACE (6.2 mm), controller: PLC system cabling of output cards, connection 1: Screw connection 1x, connection 2: D-SUB socket strip 1x 15-position, connection 3: Plug connection (Can be snapped onto 8x PLC-INTERFACE terminals), number of channels: 8, control logic: positive switching     DIN rail DIN rail, unperforated - NS 35/ 7,5 V2A UNPERF 2000MM - 0801377 DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Stainless steel V2A, uncoated, length: 2000 mm, color: silver     DIN rail perforated - NS 35/ 7,5 PERF 2000MM - 0801733 DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized, passivated with a thick layer, length: 2000 mm, color: silver     DIN rail, unperforated - NS 35/ 7,5 CU UNPERF 2000MM - 0801762 DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated, length: 2000 mm, color: copper-colored     DIN rail, unperforated - NS 35/15 UNPERF 2000MM - 1201714 DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized, passivated with a thick layer, length: 2000 mm, color: silver     05/07/2020   Page 11 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories DIN rail, unperforated - NS 35/15 CU UNPERF 2000MM - 1201895 DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper, uncoated, length: 2000 mm, color: copper-colored     DIN rail, unperforated - NS 35/15-2,3 UNPERF 2000MM - 1201798 DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel, galvanized, passivated with a thick layer, length: 2000 mm, color: silver     DIN rail, unperforated - NS 35/15 AL UNPERF 2000MM - 1201756 DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum, uncoated, length: 2000 mm, color: silver     DIN rail perforated - NS 35/15 PERF 2000MM - 1201730 DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized, passivated with a thick layer, length: 2000 mm, color: silver     DIN rail, unperforated - NS 35/ 7,5 UNPERF 2000MM - 0801681 DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized, passivated with a thick layer, length: 2000 mm, color: silver     Labeled terminal marker 05/07/2020   Page 12 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories Zack marker strip - ZB 6,LGS:FORTL.ZAHLEN - 1051016 Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: consecutive numbers 1 ... 10, 11 ... 20, etc. up to 491 ... 500, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual labels: 10     Partition plate Separating plate - PLC-ATP BK - 2966841 Separating plate, 2 mm thick, required at the start and end of a PLC terminal strip. Furthermore, it is used for: visual separation of groups, safe isolation of different voltages of neighboring PLC relays in acc. with DIN VDE 0106-101, isolation     Power module Power terminal block - PLC-ESK GY - 2966508 Power terminal block, for the input of up to four potentials, for mounting on NS 35/7.5     Screwdriver tools Screwdriver - SZF 1-0,6X3,5 - 1204517 Actuation tool, for ST terminal blocks, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2component grip, with non-slip grip     Terminal marking 05/07/2020   Page 13 / 15 https://www.phoenixcontact.com/us/products/2909524 Relay Module - PLC-RSC-24DC/21/EX - 2909524 Accessories Zack marker strip - ZB 6:UNBEDRUCKT - 1051003 Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual labels: 10     Zack marker strip - ZB 6/WH-100:UNBEDRUCKT - 5060935 Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm, Number of individual labels: 10     Marker for terminal blocks - UC-TM 6 - 0818085 Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm, Number of individual labels: 80     Marker for terminal blocks - UCT-TM 6 - 0828736 Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER, BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0, THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 5.6 x 10.5 mm, Number of individual labels: 60     Spare parts Single relay - REL-MR- 24DC/21 - 2961105 Plug-in miniature power relay, with power contact, 1 PDT, input voltage 24 V DC     05/07/2020   Page 14 / 15 https://www.phoenixcontact.com/us/products/2909524 Phoenix Contact 2020 © - all rights reserved http://www.phoenixcontact.com 05/07/2020   Page 15 / 15