QUINT4-PS/24DC/24DC/5/PT
DC/DC converter
Data sheet
108883_en_00
1
© PHOENIX CONTACT 2019-07-15
Description
QUINT POWER DC/DC converters with SFB Technology
and preventive function monitoring ensure superior system
availability.
Technical data (short form)
Input voltage range
24 V DC -25 % ... +40 %
Mains buffering
typ. 14 ms (24 V DC)
Nominal output voltage (UN)
24 V DC
Setting range of the output voltage
(USet)
24 V DC ... 29.5 V DC
Nominal output current (IN)
Static Boost (IStat.Boost)
Dynamic Boost (IDyn.Boost)
Selective Fuse Breaking (ISFB)
5A
6.25 A
10 A (5 s)
30 A (15 ms)
Output power (PN)
Output power (PStat. Boost)
Output power (PDyn. Boost)
120 W
150 W
240 W (5 s)
Efficiency
typ. 92.2 % (24 V DC)
Residual ripple
< 10 mVPP
Powerful
–
–
SFB Technology: 6 times the nominal current for 15 ms
Power reserves:
Static boost of up to 125% (PN) for a sustained period
Dynamic boost of up to 200% (PN) for 5 s
Robust
–
ATEX/IECEX approval
Preventive
–
Comprehensive signaling:
Analog signal, digital signal, relay contact, LED bar
graph
Flexible connection technology
–
–
MTBF (IEC 61709, SN 29500)
> 930000 h (40 °C)
Ambient temperature (operation)
-25 °C ... 70 °C
-40°C (startup type tested)
> 60 °C Derating: 2.5 %/K
Dimensions W/H/D
36 mm / 130 mm / 125 mm
Weight
0.6 kg
Tried-and-tested screw connection
Fast Push-in connection
All technical specifications are nominal values and refer to a room temperature of 25 °C and 70 % relative
humidity at 100 m above sea level.
QUINT4-PS/24DC/24DC/5/PT
2
Table of contents
1
Description .............................................................................................................................. 1
2
Table of contents ..................................................................................................................... 2
3
Ordering data .......................................................................................................................... 3
4
Technical data ......................................................................................................................... 5
5
Safety and installation notes .................................................................................................. 15
6
High-voltage test (HIPOT) ..................................................................................................... 16
7
Structure of the power supply ................................................................................................ 17
8
Mounting/removing the power supply .................................................................................... 20
9
Device connection terminal blocks ........................................................................................ 24
10
Output characteristic curves .................................................................................................. 25
11
Configuring the power supply ................................................................................................ 28
12
Boost currents ....................................................................................................................... 29
13
SFB Technology .................................................................................................................... 31
14
Signaling................................................................................................................................ 35
15
Operating modes ................................................................................................................... 43
16
Derating................................................................................................................................. 45
108883_en_00
PHOENIX CONTACT 2 / 48
QUINT4-PS/24DC/24DC/5/PT
3
Ordering data
Description
Order No.
Pcs./Pkt.
Primary-switched DC/DC converter, QUINT, DIN rail
QUINT4-PS/24DC/24DC/5/
mounting, SFB Technology (Selective Fuse Breaking),
PT
Push-in connection, input: 24 V DC, output: 24 V DC / 5 A
2910119
1
Accessories
Order No.
Pcs./Pkt.
Universal wall adapter for securely mounting the device in UWA 182/52
the event of strong vibrations. The device is screwed
directly onto the mounting surface. The universal wall
adapter is attached on the top/bottom.
2938235
1
2-piece universal wall adapter for securely mounting the
device in the event of strong vibrations. The profiles that
are screwed onto the side of the device are screwed
directly onto the mounting surface. The universal wall
adapter is attached on the left/right.
UWA 130
2901664
1
Assembly adapter for QUINT-PS... power supply on S7300 rail
QUINT-PS-ADAPTERS7/1
2938196
1
Near Field Communication (NFC) programming adapter
with USB interface for the wireless configuration of NFCcapable products from PHOENIX CONTACT with
software. No separate USB driver is required.
TWN4 MIFARE NFC USB
ADAPTER
2909681
1
Multi-channel electronic device circuit breaker for
CBMC E4 24DC/1-4A NO
protecting four loads at 24 V DC in the event of overload
and short circuit. With electronic locking of the set nominal
currents. For installation on DIN rails.
2906031
1
Multi-channel electronic device circuit breaker for
CBMC E4 24DC/1-10A NO
protecting four loads at 24 V DC in the event of overload
and short circuit. With electronic locking of the set nominal
currents. For installation on DIN rails.
2906032
1
Multi-channel electronic circuit breaker with IO-Link
CBMC E4 24DC/1-4A+ IOL
interface for protecting four loads at 24 V DC in the event
of overload and short circuit. With electronic locking of the
set nominal currents. For installation on DIN rails.
2910410
1
Multi-channel electronic circuit breaker with IO-Link
CBMC E4 24DC/1-10A IOL
interface for protecting four loads at 24 V DC in the event
of overload and short circuit. With electronic locking of the
set nominal currents. For installation on DIN rails.
2910411
1
108883_en_00
Type
Type
PHOENIX CONTACT 3 / 48
QUINT4-PS/24DC/24DC/5/PT
Accessories
Type
Order No.
Pcs./Pkt.
Multi-channel, electronic device circuit breaker with active CBM E4 24DC/0.5-10A NO-R 2905743
current limitation for protecting four loads at 24 V DC in the
event of overload and short circuit. With nominal current
assistant and electronic locking of the set nominal
currents. For installation on DIN rails.
1
Multi-channel, electronic device circuit breaker with active CBM E8 24DC/0.5-10A NO-R 2905744
current limitation for protecting eight loads at 24 V DC in
the event of overload and short circuit. With nominal
current assistant and electronic locking of the set nominal
currents. For installation on DIN rails.
1
The range of accessories is being continuously extended. The current range of accessories can be found in
the download area for the product.
108883_en_00
PHOENIX CONTACT 4 / 48
QUINT4-PS/24DC/24DC/5/PT
4
Technical data
Input data
Unless otherwise stated, all data applies for 25°C ambient temperature, 24 V DC input voltage, and nominal
output current (IN).
Input voltage range
24 V DC -25 % ... +40 %
Electric strength, max.
35 V DC (60 s)
Current draw typ.
6.9 A (24 V DC)
Mains buffering
typ. 14 ms (24 V DC)
Switch-on time
24 V DC,
constant capacity )
24 V DC ... 29.5 V DC
Nominal output current (IN)
5A
Static Boost (IStat.Boost)
6.25 A
Dynamic Boost (IDyn.Boost)
10 A (5 s)
Selective Fuse Breaking (ISFB)
30 A (15 ms)
Magnetic circuit breaker tripping
A1 ... A4 / B2 / C1 ... C2 / Z1 ... Z4
Control deviation change in load, static 10 % ... 90 %
100%
LED lights up yellow, output power > 120 W
POut > 75%
LED lights up green, output power > 90 W
POut > 50%
LED lights up green, output power > 60 W
UOut > 0.9 x USet
LED lights up green
UOut < 0.9 x USet
LED flashes green
UIn > 0.8 x UInNom
LED off
UIn < 0.8 x UInNom
LED lights up yellow
108883_en_00
PHOENIX CONTACT 7 / 48
QUINT4-PS/24DC/24DC/5/PT
Signal contacts
Signal output Out 1 (configurable)
Connection labeling
3.5 +
Digital
0 / 24 V DC , 20 mA
Default
UIN input voltage OK
Signal option
Output voltage
Output current
Output power
Operating hours
Early warning of high temperatures
OVP voltage limitation active
Signal output Out 2 (configurable)
Connection labeling
3.6 +
Digital
0 / 24 V DC , 20 mA
Default
Output power
Signal option
Output voltage
Output current
Operating hours
Early warning of high temperatures
OVP voltage limitation active
Analog
4 mA ... 20 mA ±5 % ( Load ≤400 )
Signal option
Output voltage
Output current
Output power
Signal output Relay 13/14 (configurable)
Connection labeling
3.1, 3.2
Switch contact (floating)
floating
Maximum contact load
24 V DC 1 A , 30 V AC 0.5 A
Default
Output voltage
Signal option
Output current
Output power
Operating hours
Early warning of high temperatures
OVP voltage limitation active
UIN input voltage OK
Remote signal input (configurable)
Connection labeling
3.3 +
Function
Output power ON/OFF (remote)
Default
Output power ON (>40 kΩ/24 V DC/open bridge between REM
and SGnd)
Signal ground SGnd
Connection labeling
3.4 +
Function
Signal ground
Reference potential
to OUT1, OUT2, REM
108883_en_00
PHOENIX CONTACT 8 / 48
QUINT4-PS/24DC/24DC/5/PT
Signal connection data
Connection method
Push-in connection
Conductor cross section, solid
0.2 mm² ... 1 mm²
Conductor cross section, flexible
0.2 mm² ... 1.5 mm²
Conductor cross section flexible, with ferrule with plastic
sleeve
0.2 mm² ... 0.75 mm²
Conductor cross section flexible, with ferrule without
plastic sleeve
0.2 mm² ... 1.5 mm²
Conductor cross section AWG
24 ... 16
Stripping length
8 mm
Reliability
24 V DC
MTBF (IEC 61709, SN 29500)
> 1600000 h (25 °C)
> 930000 h (40 °C)
> 380000 h (60 °C)
Life expectancy (electrolytic capacitors)
Output current (IOut)
24 V DC
2.5 A
> 422000 h ( 40 °C )
5A
> 260000 h ( 40 °C )
5A
> 520000 h ( 30 °C )
The expected service life is based on the capacitors used. If the capacitor specification is observed, the
specified data will be ensured until the end of the stated service life. For runtimes beyond this time, error-free
operation may be reduced. The specified service life of more than 15 years is simply a comparative value.
Min.
Max.
Auxiliary converter stage
Switching frequency
190 kHz
220 kHz
Main converter stage
50 kHz
420 kHz
General data
Degree of protection
IP20
Protection class
Special with SELV input and output
Inflammability class in acc. with UL 94 (housing / terminal V0
blocks)
Side element version
Aluminum
Hood version
Stainless steel X6Cr17
Dimensions W / H / D (state of delivery)
36 mm / 130 mm / 125 mm
Dimensions W / H / D (90° turned)
122 mm / 130 mm / 39 mm
Weight
0.6 kg
Power dissipation
24 V DC
Maximum power dissipation in no-load condition
2000 m, observe derating)
Vibration (operation)
5 Hz ... 100 Hz resonance search 2.3g, 90 min., resonance
frequency 2.3g, 90 min. (according to DNV GL Class C)
Shock
18 ms, 30g, in each space direction (according to IEC 600682-27)
Degree of pollution
2
Climatic class
3K3 (EN 60721)
Overvoltage category
EN 61010-1
EN 62477-1
II
III
108883_en_00
PHOENIX CONTACT 10 / 48
QUINT4-PS/24DC/24DC/5/PT
Standards
Electrical safety (of control and regulation devices)
IEC 61010-1
SELV
EN 61010-1 (SELV)
IEC 61010-2-201 (PELV)
Network version/undervoltage
EN 61000-4-29
EMC requirements, power plant
IEC 61850-3
EN 61000-6-5
Explosive atmospheres
IEC 60079-0
IEC 60079-7
IEC 60079-11
IEC 60079-15
Approvals
ATEX
II 3 G Ex ec ic nC IIC T4 Gc X
IECEx
IECEx SIQ 19.0003X
Ex ec ic nC IIC T4 Gc
UL
UL Listed UL 61010-1
UL Listed UL 61010-2-201
UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D T4
(Hazardous Location)
CSA
CAN/CSA-C22.2 No. 61010-1-12
CAN/CSA-IEC 61010-2-201:14
SIQ
BG (type approved)
CB-Scheme (IEC 61010-1, IEC 61010-2-201)
Shipbuilding
DNV GL, ABS
108883_en_00
PHOENIX CONTACT 11 / 48
QUINT4-PS/24DC/24DC/5/PT
Electromagnetic compatibility
Noise emission according to EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
CE basic standard
Minimum normative
requirements
Higher requirements in
practice (covered)
Conducted noise emission EN 55016
EN 61000-6-4 (Class A)
EN 61000-6-3 (Class B)
Noise emission EN 55016
EN 61000-6-4 (Class A)
EN 61000-6-3 (Class B)
Minimum normative
requirements of DNV GL
Higher requirements in
practice of DNV GL
(covered)
DNV GL conducted noise emission
Class A
Area power distribution
Class B
Bridge and deck area
DNV GL noise radiation
Class A
Area power distribution
Class B
Bridge and deck area
Noise emission for marine approval
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial), and EN 61000-6-5 (power station
equipment zone), IEC/EN 61850-3 (energy supply)
CE basic standard
Minimum normative
requirements of EN 610006-2 (CE)
(immunity for industrial
environments)
Higher requirements in
practice (covered)
Electrostatic discharge EN 61000-4-2
Housing contact discharge
4 kV (Test Level 2)
8 kV (Test Level 4)
Housing air discharge
8 kV (Test Level 3)
15 kV (Test Level 4)
Criterion B
Criterion A
Comments
Electromagnetic HF field EN 61000-4-3
Frequency range
80 MHz ... 1 GHz
80 MHz ... 1 GHz
Test field strength
10 V/m (Test Level 3)
20 V/m (Test Level 3)
Frequency range
1.4 GHz ... 2 GHz
1 GHz ... 6 GHz
Test field strength
3 V/m (Test Level 2)
10 V/m (Test Level 3)
Frequency range
2 GHz ... 2.7 GHz
1 GHz ... 6 GHz
Test field strength
1 V/m (Test Level 1)
10 V/m (Test Level 3)
Criterion A
Criterion A
Input
2 kV (Test Level 3 asymmetrical)
2 kV (Test Level 3 asymmetrical)
Output
2 kV (Test Level 3 asymmetrical)
2 kV (Test Level 3 asymmetrical)
Signal
1 kV (Test Level 3 asymmetrical)
2 kV (Test Level 4 asymmetrical)
Criterion B
Criterion A
Comments
Fast transients (burst) EN 61000-4-4
Comments
108883_en_00
PHOENIX CONTACT 12 / 48
QUINT4-PS/24DC/24DC/5/PT
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial), and EN 61000-6-5 (power station
equipment zone), IEC/EN 61850-3 (energy supply)
CE basic standard
Minimum normative
requirements of EN 610006-2 (CE)
(immunity for industrial
environments)
Higher requirements in
practice (covered)
Input
0.5 kV (Test Level 2 symmetrical)
1 kV (Test Level 2 asymmetrical)
1 kV (Test Level 3 symmetrical)
2 kV (Test Level 3 asymmetrical)
Output
0.5 kV (Test Level 2 symmetrical)
1 kV (Test Level 2 asymmetrical)
1 kV (Test Level 3 symmetrical)
2 kV (Test Level 3 asymmetrical)
Signal
1 kV (Test Level 2 asymmetrical)
2 kV (Test Level 3 asymmetrical)
Criterion B
Criterion A
asymmetrical
asymmetrical
0.15 MHz ... 80 MHz
0.15 MHz ... 80 MHz
10 V (Test Level 3)
10 V (Test Level 3)
Criterion A
Criterion A
50 Hz , 60 Hz ( 30 A/m )
16.7 Hz , 50 Hz , 60 Hz
( 100 A/m 60 s )
not required
50 Hz , 60 Hz ( 1 kA/m , 3 s )
not required
0 Hz ( 300 A/m , DC, 60 s )
Criterion A
Criterion A
Surge voltage load (surge) EN 61000-4-5
Comments
Conducted interference EN 61000-4-6
Input/Output/Signal
Frequency range
Voltage
Comments
Power frequency magnetic field EN 61000-4-8
Comments
Additional basic standard EN 61000-6-5 (immunity in power station), IEC/EN 61850-3 (energy supply)
Basic standard
Minimum normative
requirements of EN 610006-5
Higher requirements in
practice (covered)
not required
1000 A/m
none
Criterion A
not required
100 kHz
100 A/m
not required
1 MHz
100 A/m
none
Criterion A
Pulse-shape magnetic field EN 61000-4-9
Comments
Damped oscillating magnetic field EN 61000-4-10
Comments
108883_en_00
PHOENIX CONTACT 13 / 48
QUINT4-PS/24DC/24DC/5/PT
Additional basic standard EN 61000-6-5 (immunity in power station), IEC/EN 61850-3 (energy supply)
Basic standard
Minimum normative
requirements of EN 610006-5
Higher requirements in
practice (covered)
Asymmetrical conducted disturbance variables EN 61000-4-16
Input, Output, Signals 15 Hz ... 150 Hz , 10 V on 1 V 15 Hz ... 150 Hz , 10 V on 1 V
150 Hz ... 1.5 kHz , 1 V
150 Hz ... 1.5 kHz , 1 V
1.5 kHz ... 15 kHz , 1 V on 10 V 1.5 kHz ... 15 kHz , 1 V on 10 V
15 kHz ... 150 kHz , 10 V
15 kHz ... 150 kHz , 10 V
( Test Level 3 )
( Test Level 3 )
50 Hz , 60 Hz , 10 V
(Permanent)
50 Hz , 60 Hz , 100 V (1 s)
Comments
( Test Level 3 )
16.7 Hz, 50 Hz, 60 Hz, 150 Hz,
180 Hz , 10 V (Permanent)
0 Hz , 16.7 Hz , 50 Hz , 60 Hz ,
100 V (1 s)
( Test Level 3 )
Criterion A
Criterion A
10 % (UN) , 50 Hz
15 % (UN) , 50 Hz , 100 Hz ,
150 Hz
14 % (UN) , 300 Hz
Criterion B
Criterion A
Alternating component of DC voltage EN 61000-4-17
Alternating component
Comments
Attenuated oscillating wave EN 61000-4-18
Input, Output 1 MHz 0.5 kV ( Test Level 2 symmetrical )
100 kHz , 1 MHz , 1 kV ( Test
Level 3 - symmetrical )
1 MHz , 1 kV 10
100 kHz , 1 MHz , 1 kV
MHz 0.5 kV
10 MHz , 0.5 kV
( Test Level 2 - asymmetrical ) ( Test Level 2 - asymmetrical )
Signals 1 MHz , 0.5 kV ( Test Level 2 - 100 kHz , 1 MHz , 0.5 kV ( Test
symmetrical )
Level 2 - symmetrical )
1 MHz , 1 kV
100 kHz , 1 MHz , 1 kV
( Test Level 2 - asymmetrical ) ( Test Level 2 - asymmetrical )
Comments
Criterion B
Criterion A
Voltage dips EN 61000-4-29
Input voltage ( 24 V DC )
Voltage dip 70 % , 100 ms ( Test Level 2 ) 70 % , 100 ms ( Test Level 2 )
Comments
Criterion C
Voltage dip 40 % , 100 ms ( Test Level 2 )
Criterion A
40 % 100 ms ( Test Level 2 )
Comments
Criterion C
Criterion A
Voltage dip
0 % , 50 ms ( Test Level 2 )
0 % , 50 ms ( Test Level 2 )
Comments
Criterion B
Criterion B
Key
Criterion A
Normal operating behavior within the specified limits.
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects
automatically or which can be restored by actuating the operating elements.
108883_en_00
PHOENIX CONTACT 14 / 48
QUINT4-PS/24DC/24DC/5/PT
5
Safety and installation notes
Only qualified electricians may install, start up, and operate
the device. Observe the national safety and accident
prevention regulations.
The specified technical characteristics relate to the factory
setting of the standard device.
Configured devices may have different technical
characteristics. The device behavior may also differ from the
documentation.
CAUTION: Before startup, observe the
following
Check the device for external damage. If the
device is defective, it must not be used.
The power supply must be switched off from
outside according to IEC 61010 (e.g., via the
line protection on the primary side).
Preferably mount the power supply in the
normal mounting position.
Ensure that the primary-side and secondaryside wiring of the power supply are the correct
size and have sufficient fuse protection.
The power supply is a built-in device. The
IP20 degree of protection of the power supply
is intended for a clean and dry environment.
The power supply is mounted in a control
cabinet.
For the connection parameters for wiring the
power supply, such as the required stripping
length with and without ferrule, refer to the
technical data section.
The power supply may only be used for its
intended use.
The continuous total output power may not
exceed PN at 60 °C ambient temperature and
PStat. Boost at 40°C ambient temperature.
Observe all the maximum output powers for
all operating conditions.
The following applies for use in ATEX /
IECEx- applications (EN 60079- 15):
lnstall the device in a suitable approved
housing (with at least IP54 protection) that
meets the requirements of EN 60079-15. The
device must be deactivated and immediately
removed from the Ex area if it is damaged, has
been subject to an impermissible Ioad, has
been stored incorrectly, or malfunctions. The
device is designed for installation in zone 2
potentially explosive areas according to
Directive 2014/34/EU.
Ensure cables are correctly sized for the max.
input/output current and have fuse protection
or install a suitable upstream device for
current Iimitation in order to prevent incendive
temperatures according to EN 60079-15.
The equipment shall only be used in an area
of not more than pollution degree 2, as
defined in EN 60664-1.
Do not operate voltage adjustment when an
explosive atmosphere is present.
To avoid accidental contact with live parts,
always cover the termination area
(e.g., installation in the control cabinet).
DANGER: Hazardous voltage
The power supply contains components that
have been designed for operation at
potentially lethal voltages. The accumulated
level of energy can also be high. Never carry
out work when mains voltage is present.
CAUTION: Hot surface
Depending on the ambient temperature and
load on the power supply, the housing can
become hot.
The power supply is maintenance-free.
Repairs may only be carried out by the
manufacturer. The warranty no longer applies
if the housing is opened.
108883_en_00
PHOENIX CONTACT 15 / 48
QUINT4-PS/24DC/24DC/5/PT
High-voltage test (HIPOT)
This power supply is subject to the Low Voltage Directive
and is factory tested. During the HIPOT test (high-voltage
test), the insulation between the input circuit and output
circuit is tested for the prescribed electric strength values,
for example. The test voltage in the high-voltage range is
applied at the input and output terminal blocks of the power
supply. The operating voltage used in normal operation is
considerably lower than the test voltage used.
6.1
PE
High-voltage dielectric test (dielectric strength
test)
QUINT POWER Ord.No.XXXXXXX
6
1
2.1
2.2
2.3
2.4
+ + − −
Output DC
UOut
Signal
13
14
Rem
SGnd
Out 1
Out 2
3.1
3.2
3.3
3.4
3.5
3.6
2
> 100% Boost
> 75%
POut
> 50%
DC OK
UIn
In order to ensure permanent safe isolation of the DC input
circuit and DC output circuit, high-voltage testing is
performed as part of the safety approval process (type test)
and manufacturing (routine test).
HV
=/=
3
Input DC
+ −
1.1
6.2
1.2
High-voltage dielectric test during the
manufacturing process
During the manufacturing process for the power supply, a
high-voltage test is performed as part of the dielectric test in
accordance with the specifications of IEC/UL/EN 61010-1.
The high-voltage test is performed with a test voltage of at
least 2 kV DC or higher. Routine manufacturing tests are
inspected regularly by a certification authority.
4
Figure 1
Potential-related wiring for the high-voltage
test
Key
6.3
High-voltage dielectric test performed by the
customer
Apart from routine and type tests to guarantee electrical
safety, the end user does not have to perform another highvoltage test on the power supply as an individual
component. According to EN 60204-1 (Safety of machinery
- Electrical equipment of machines) the power supply can be
disconnected during the high-voltage test and only installed
once the high-voltage test has been completed.
6.3.1
No. Designation
Color coding
1
2
3
Blue
Blue
--
Potential
levels
Potential 1
Potential 1
--
Red
Potential 2
4
DC output circuit
Signal contacts
High-voltage
tester
DC input circuit
Performing high-voltage testing
If high-voltage testing of the control cabinet or the power
supply as a stand-alone component is planned during final
inspection and testing, the following features must be
observed.
– The power supply wiring must be implemented as
shown in the wiring diagram.
– The maximum permissible test voltages must not be
exceeded.
Avoid unnecessary loading or damage to the power supply
due to excessive test voltages.
For the relevant applicable test voltages and
insulation distances, refer to the
corresponding table (see technical data:
electric strength of the insulation section).
108883_en_00
PHOENIX CONTACT 16 / 48
QUINT4-PS/24DC/24DC/5/PT
Structure of the power supply
7.2
Device dimensions
The fanless convection-cooled power supply can be
snapped onto all DIN rails according to EN 60715.
QUINT POWER Ord.No.XXXXXXX
7.1
36
Function elements
2
QUINT POWER Ord.No.XXXXXXX
9
65
1
2
2.1
2.2
2.3
Output DC
3
Signal
13
14
Rem
SGnd
Out 1
Out 2
2.2
2.3
2.4
+ + − −
Output DC
UOut
Signal
13
14
Rem
SGnd
Out 1
Out 2
> 100% Boost
> 75%
POut
> 50%
DC OK
UIn
2.4
+ + − −
UOut
2.1
3.1
3.2
3.3
3.4
3.5
3.6
130
7
3.1
3.2
3.3
3.4
3.5
3.6
Input DC
> 100% Boost
> 75%
POut
> 50%
DC OK
UIn
8
+ −
1.1
4
5
Figure 3
1.2
Device dimensions (dimensions in mm)
Input DC
+ −
1.1
1.2
6
131
125
122
2
Figure 2
7
2
Operating and indication elements
108883_en_00
80
Designation
DC output voltage connection terminal blocks
Accommodation for cable binders
Signaling connection terminal blocks
Status and diagnostics indicators
Position NFC interface (Near Field Communication)
QR code web link
DC input voltage connection terminal blocks
Universal DIN rail adapter (rear of housing)
Output voltage button (-) / (+)
45
No.
1
2
3
4
5
6
7
8
9
130
Key
Figure 4
Device dimensions (dimensions in mm)
PHOENIX CONTACT 17 / 48
QUINT4-PS/24DC/24DC/5/PT
7.3
Keep-out areas
Nominal output
capacity
Spacing [mm]
b
40
50
a
0
5
< 50 %
≥ 50 %
c
20
50
If adjacent components are active and the
nominal output power ≥ 50%, there must be
lateral spacing of 15 mm.
36
a
130
QUINT POWER Ord.No.XXXXXXX
b
a
2.1
2.2
2.3
2.4
+ + − −
Output DC
UOut
Signal
13
14
Rem
SGnd
Out 1
Out 2
3.1
3.2
3.3
3.4
3.5
3.6
> 100% Boost
> 75%
POut
> 50%
DC OK
UIn
Input DC
+ −
1.2
c
1.1
Figure 5
108883_en_00
Device dimensions and minimum keep-out
areas (in mm)
PHOENIX CONTACT 18 / 48
QUINT4-PS/24DC/24DC/5/PT
7.4
Block diagram
+
1.1
-
1.2
U
2.1
2.2
2.3
2.4
3.1
3.2
OVP
3.3
3.4
3.5
C
3.6
+
+
13
14
Rem
SGnd
OUT1
OUT2
NFC
Figure 6
Block diagram
Key
Symbol
Designation
Surge protection (varistor) with filter
Symbol
OVP
Designation
Additional regulatory protection against
surge voltage
Reverse polarity protection
Switch
Inrush current limitation
PNP transistor switch output
Switching transistor and main transmitter
(electrically isolating)
Secondary rectification and smoothing
C
NFC
Microcontroller
Passive NFC interface (Near Field
Communication)
Filter
Output voltage button (-) / (+)
Auxiliary converter (electrically isolating)
Signal/display LEDs
Optocoupler (electrically isolating)
108883_en_00
PHOENIX CONTACT 19 / 48
QUINT4-PS/24DC/24DC/5/PT
8
Mounting/removing the power
supply
8.1
Mounting the power supply unit
D
Proceed as follows to mount the power supply:
1. In the normal mounting position the power supply is
mounted on the DIN rail from above. Make sure that the
universal DIN rail adapter is in the correct position
behind the DIN rail (A).
2. Then press the power supply down until the universal
DIN rail adapter audibly latches into place (B).
3. Check that the power supply is securely attached to the
DIN rail.
C
A
Figure 8
A
8.3
B
Removing the power supply from the DIN rail
Retrofitting the universal DIN rail adapter
For installation in horizontal terminal boxes it is possible to
mount the power supply at a 90° angle to the DIN rail.
No additional mounting material is required.
Click
Figure 7
8.2
Use the Torx screws provided to attach the
universal DIN rail adapter to the side of the
power supply.
B
Snapping the power supply onto the DIN rail
Removing the power supply unit
Proceed as follows to remove the power supply:
1. Take a suitable screwdriver and insert this into the lock
hole on the universal DIN rail adapter (A).
2. Release the lock by lifting the screwdriver (B).
3. Carefully swivel the power supply forward (C) so that
the lock slides back into the starting position.
4. Then separate the power supply from the DIN rail (D).
8.3.1
Disassembling the universal DIN rail adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
Figure 9
108883_en_00
Disassembling the universal DIN rail adapter
PHOENIX CONTACT 20 / 48
QUINT4-PS/24DC/24DC/5/PT
8.3.2
Mounting the universal DIN rail adapter
To mount the universal DIN rail adapter on the left side of the
device, proceed as follows:
1. Position the universal DIN rail adapter on the left side of
the housing so that the mounting holes are congruent
with the hole pattern for the mounting holes.
2. Insert the Torx screws that were removed earlier into the
appropriate hole pattern on the universal DIN rail
adapter so that the necessary drill holes on the power
supply can be accessed.
3. Screw the universal DIN rail adapter onto the power
supply.
The maximum tightening torque of the Torx
screw (Torx® T10) is 0.7 Nm.
Figure 10
8.4
8.4.1
Mounting the UWA 182/52 universal wall
adapter
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter in such a way that
the keyholes or oval tapers face up. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes on the power supply can be accessed.
6. Screw the universal wall adapter onto the power supply.
Mounting the universal DIN rail adapter
Retrofitting the universal wall adapter
Figure 11
The UWA 182/52 universal wall adapter (Order No.
2938235) or UWA 130 universal wall adapter (Order No.
2901664) is used to attach the power supply directly to the
mounting surface.
The use of universal wall adapters is recommended under
extreme ambient conditions, e.g., strong vibrations. Thanks
to the tight screw connection between the power supply and
the universal wall adapter or the actual mounting surface, an
extremely high level of mechanical stability is ensured.
Mounting the UWA 182/52 universal wall
adapter
The maximum tightening torque of the Torx
screw (Torx® T10) is 0.7 Nm.
Make sure you use suitable mounting material
when attaching to the mounting surface.
The power supply is attached to the UWA 182
or UWA 130 universal wall adapter by means
of the Torx screws of the universal DIN rail
adapter.
108883_en_00
PHOENIX CONTACT 21 / 48
QUINT4-PS/24DC/24DC/5/PT
8.4.2
Mounting the UWA 130 2-piece universal wall
adapter
Fix connection wiring to the power supply
Two receptacles for the bundled attachment of the
connection wiring are integrated in the left and right housing
panel. Use cable binders to secure the connection wiring
(optional PKB 140X3,6 - Order No. 1005460).
Proceed as follows to secure the connection wiring:
– Wire the power supply with sufficient connection
reserve (input terminal blocks, output terminal blocks,
signal terminal blocks)
– Bundle and set up the connection wiring so that the
cooling grilles on the top and bottom of the housing are
covered as little as possible.
– Thread the cable binders into the necessary
receptacles for the cable binders.
QUINT POWER Ord.No.xxxxxxx
Proceed as follows to disassemble the universal DIN rail
adapter that comes pre-mounted:
1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
2. Separate the universal DIN rail adapter from the rear of
the power supply.
3. Position the universal wall adapter. The mounting
surface for the power supply is the raised section of the
universal wall adapter.
4. Place the power supply on the universal wall adapter in
the normal mounting position (input voltage connection
terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes in the side flanges of the power supply
can be accessed.
6. Screw the two-piece universal wall adapter onto the
power supply.
8.5
2.1
+
2.2
+
Ou
tpu
2.3
−
tD
C
2.4
−
13
14
Re
3.1
m
SG
3.2
nd
Ou
3.3
t
Ou 1
3.4
t2
3.5
>1
0
> 7 0%
3.6
5
> 5 % Boo
st
0%
Figure 13
–
Secure the connection wiring with the cable binders.
Make sure that the connection wiring is attached safely
and securely without damaging the connection wiring.
Mounting the UWA 130 universal wall adapter
QUINT POWER Ord.No.xxxxxxx
Figure 12
Lay and align connection wiring
2.1
+
2.2
+
Ou
tpu
2.3
−
tD
C
13
14
Re
m
SG
nd
Ou
t
Ou 1
t2
2.4
−
3.1
3.2
3.3
3.4
3.5
>1
0
> 7 0%
3.6
5
> 5 % Boo
st
0%
Figure 14
108883_en_00
Secure connection wiring with cable binder
PHOENIX CONTACT 22 / 48
QUINT4-PS/24DC/24DC/5/PT
Shorten the excess length of the cable binder ends.
Then check again that the connection wiring is properly
secured.
QUINT POWER Ord.No.xxxxxxx
–
–
2.1
+
2.2
+
Ou
tpu
2.3
−
tD
C
2.4
−
13
14
Re
3.1
m
SG
3.2
nd
Ou
3.3
t
Ou 1
3.4
t2
3
>1
.5
0
> 7 0%
3.6
5
> 5 % Boo
st
0%
Figure 15
Shorten protruding ends of the cable binder
NOTE: Mechanical damage to the connection
wiring caused by friction
In extreme ambient conditions, e.g., strong
vibrations, protect the connection wiring
against mechanical damage using additional
insulation material. The additional insulation
material for protecting the connection wiring is
limited to the area where the cable binders are
attached.
108883_en_00
PHOENIX CONTACT 23 / 48
QUINT4-PS/24DC/24DC/5/PT
9
Device connection terminal blocks
The front-mounted DC input and DC output terminal blocks
and the signal terminal blocks of the power supply feature
Push-in connection technology. The wiring is performed by
plugging in, without tools.
For the necessary connection parameters for
the connection terminal blocks, refer to the
technical data section.
9.3
By default, the power supply is pre-set to a nominal output
voltage of 24 V DC.
The output voltage is adjusted via the two arrow keys (-)
and (+) on the front of the power supply.
When you press the arrow key once briefly, the output
voltage is reduced (-) or increased (+) by 3 mV. When you
press the arrow key for longer, the voltage is adjusted in
100 mV increments.
9.4
9.1
Input
The power supply is connected on the primary side via the
Input +/- connection terminal blocks.
9.2
Protection of the primary side
Installation of the device must correspond to EN 61010
regulations. It must be possible to switch off the device using
a suitable disconnecting device outside the power supply.
The line protection on the primary side is suitable for this
(see technical data section).
Output
Protection of the secondary side
The power supply is electronically short-circuit-proof and
no-load-proof. In the event of an error, the output voltage is
limited
If sufficiently long connecting cables are used,
fuse protection does not have to be provided
for each individual load.
If each load is protected separately with its
own protective device, the selective shutdown
in the event of a fault enables the system to
remain operational.
Protection
Input DC 18...32 V
+
+
-
-
-
Figure 16
+
Pin assignment for DC supply voltage
DC applications require upstream installation of a fuse that
is permitted for the operating voltage.
108883_en_00
PHOENIX CONTACT 24 / 48
QUINT4-PS/24DC/24DC/5/PT
10
Output characteristic curves
This section describes the various output characteristic curves together with their areas of application for customization to
your specific application. The U/I Advanced characteristic curve is set by default.
M
Application
Normal load
Your benefits
Reliable power supply
System extension
+
-
Loads with high inrush
Energy storage charging
current
A stable 24 V, even in the No over-dimensioned
power supply unit
event of a sustained
required
overload
Fast charging
Selective tripping of
fuses
Keeps temperatures
low in the event of
faults
Short circuit, non-fused
Parallel loads continue
working
Low thermal stress in
the even of faults
Enables configuration
without fuse
Characteristics
-
U/I Advanced
-
Smart HICCUP
-
FUSE MODE
Symbol
-
-
-
Designation
Suitable for the application
-
108883_en_00
Not suitable for the application
PHOENIX CONTACT 25 / 48
QUINT4-PS/24DC/24DC/5/PT
U/I Advanced output characteristic curve
10.2
UOut [V]
The preset U/I Advanced output characteristic curve is
optimized for the following applications:
– For selective tripping of standard circuit breakers (SFB
technology). The power supply supplies up to 6 times
the nominal current for 15 ms. Loads connected in
parallel continue working.
– When supplying loads with high switch-on currents,
such as motors. The dynamic boost of the power supply
supplies up to 200% of the nominal power for 5 s. This
ensures that sufficient reserve energy is available;
overdimensioning of the power supply is not necessary.
– For system extension. With the static boost, up to
125% of the nominal output power is available for a
sustained period (up to 40°C).
– For fast energy storage charging (e.g., of batteries) to
supply a wide range of loads. The power supply
operates in the nominal operating range. Energy supply
to the load is ensured.
UN
Smart HICCUP output characteristic curve
The SMART HICCUP output characteristic curve keeps the
thermal load of the connecting cables at a low level in the
event of a sustained overload. If loads are not protected or
are protected in a way that is not permitted, the loads are
supplied for 2 s. The DC output of the power supply is then
switched off for 8 s. This procedure is repeated until the
cause of the overload has been remedied.
The preset Smart HICCUP output characteristic curve is
optimized for the following applications:
– If only a low short-circuit current is permitted.
– If following an overload or short circuit the output
voltage should be made available again automatically.
UOut [V]
10.1
UN
5s
UN
2
5s
0
IN
IStat. Boost
IDyn. Boost
IOut [A]
0
IN
IStat. Boost
IOut [A]
UN
3
IDyn. Boost
2s
IDyn. Boost 2s
IOut [A]
IOut [A]
8s
0
IDyn. Boost
5s
5s
Figure 18
t [s]
Smart HICCUP output characteristic curve
toff
0
Figure 17
108883_en_00
t [s]
U/I Advanced output characteristic curve
PHOENIX CONTACT 26 / 48
QUINT4-PS/24DC/24DC/5/PT
10.3
FUSE MODE output characteristic curve
In the event of an overload (e.g., short circuit), the power
supply switches off the DC output permanently. The value of
the switch-off threshold and the time period for which it may
be exceeded can be freely selected. The power supply is
restarted via the remote contact. As an option, the power
supply can be switched on by switching the supply voltage
on the primary side off and on.
IOut [A]
Selecting the FUSE MODE output characteristic curve sets
the following default values.
– tFuse = 100 ms
– IFuse = IN
IFuse
0
tFuse
t [s]
Figure 19
108883_en_00
FUSE MODE output characteristic curve
PHOENIX CONTACT 27 / 48
QUINT4-PS/24DC/24DC/5/PT
Configuring the power supply
With the fourth generation of the QUINT POWER power
supply, it is now possible for the first time to adapt the
behavior of the power supply. In addition to setting the
output voltage and selecting the output characteristic
curves, you can configure signal outputs Out 1, Out 2, and
floating signal contact 13/14, for example. Configuration of
the remote input for controlling the power supply or
specification of signal options and signal thresholds also
extend the range of possible applications.
11.2
To configure the power supply, proceed as follows:
– Before you can configure the power supply, it should
either be disconnected from the supply voltage or
switched to SLEEP MODE.
– To switch the power supply to SLEEP MODE, use one
of the external circuits. The following connection
versions are possible between the Rem (remote input)
and SGnd (signal ground) connection terminal blocks.
Signal
The power supply is configured via the device's internal NFC
(near field communication) interface. This is located behind
the QR code on the front.
13
14
Rem
SGnd
Out 1
Out 2
The power supply behaves like a passive
NFC tag. An auxiliary power source is
required in order to supply the power supply
with configuration data.
–
b)
SLEEP MODE connection versions
Hold the USB-PROG-ADAPTER in front of the mounted
power supply such that the NFC antenna symbol is over
the QR code.
l
na
Sig
3.1
3.2
3.3
3.4
3.5
3.6
t
UOu
13
14
Rem
nd
SG 1
t
Ou 2
t
Ou
st
o
Bo
% t
00
> 15% Pou
> 70%
> 5 OK
DC
UIn
M3
x8
Figure 21
–
CONN
DAT
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– PC or notebook (as of Windows 7, Microsoft.Net
Framework 4.5, USB 2.0 interface, 50 MB hard disk
capacity, QUINT POWER software).
– Programming adapter:
TWN4 MIFARE NFC USB ADAPTER (Order No.
2909681) is plugged into the USB interface.
– Programming software: the QUINT POWER software
has been successfully installed.
Figure 20
3.1
3.2
3.3
3.4
3.5
3.6
Ord.No.xxxxxxx
Configuration with PC software
< 15 k
a)
QUINT POWER
11.1
Configuring the power supply
NFC
11
Configuration of the power supply
In the programming interface of the QUINT POWER
software, press the [Read] button. The current device
and configuration data for the power supply is read and
displayed.
If a connection cannot be established
between the USB-PROG-ADAPTER and the
power supply, more detailed information can
be found in the user manual for the QUINT
POWER software.
108883_en_00
PHOENIX CONTACT 28 / 48
QUINT4-PS/24DC/24DC/5/PT
For information regarding the configuration of
the power supply, such as selecting the
characteristic curve and output parameters,
refer to the user manual for the QUINT
POWER software.
12
Boost currents
The power supply provides the static boost (IStat. Boost) for a
sustained load supply or the time-limited dynamic boost
(IDyn. Boost).
12.1
Configuration with NFC-capable mobile
terminal device
The QUINT POWER app enables you to conveniently
configure the power supply using a mobile terminal device,
such as a smartphone.
In order to configure the power supply via the NFC interface,
the following hardware and software requirements must be
met:
– NFC-capable mobile terminal device with Android
operating system as of Version 4.1.x (Jelly Bean)
– QUINT POWER app (Google Play Store)
For information regarding the configuration of
the power supply, such as selecting the
characteristic curve and output parameters,
please refer to the QUINT POWER app.
Static Boost
For system expansion purposes, the sustained static boost
(IStat. Boost) supports the load supply with up to 125 % of the
nominal current of the power supply. The static boost is
available at an ambient temperature of up to 40 °C.
POut [W]
11.3
PDyn. Boost
200%
PStat. Boost
PN
125%
100%
75%
-25
40
60
70
TA [°C]
Figure 22
12.2
Performance characteristic in static boost
Dynamic Boost
IOut [A]
Dynamic boost (IDyn. Boost) delivers up to 200 % of the power
supply nominal current to supply high loads. This temporary
power supply to the load lasts a maximum of 5 s at an
ambient temperature of up to 60 °C. The energy supplied
adaptively for the load supply and the recovery time (tPause)
are calculated based on the specific load situation using
algorithms (see recovery time tables).
IDyn.Boost
IBase Load
tDyn.Boost
tDyn.Boost
tPause
t [s]
Figure 23
108883_en_00
Basic curve of the dynamic boost process
PHOENIX CONTACT 29 / 48
QUINT4-PS/24DC/24DC/5/PT
If a current that is lower than the maximum
available dynamic boost current (IDyn. Boost) is
required for the same period, the recovery
time may (tPause) decrease.
12.2.1 Recovery times at an ambient temperature of
40 °C
tDyn. Boost [s]
IDyn. Boost
[A]
1
2
3
4
5
0
10
1,7
3,3
5
6,7
8,3
1
10
1,8
3,6
5,4
7,2
9
2
10
2
4
6
8
10
3
10
2,4
4,8
7,2
9,6
12
4
10
4,1
6,8
10,3
12,6
16,1
5
10
5,2
8,7
13,3
21,7
26,2
6,25
10
11
23,5
35,6
41,3
50,5
Figure 24
At an output current (IBase Load) of 2 A, the dynamic output
current (IDyn. Boost) of 10 A increases for 3 s (tDyn. Boost).
After a recovery time (tPause) of 6 s, the dynamic boost is
available once again.
tDyn. Boost [s]
IBase Load
[A]
IDyn. Boost
[A]
1
2
3
4
5
0
10
1,7
3,3
5
6,7
8,3
1
10
1,8
3,6
5,4
7,2
9
2
10
2
4
6
8
10
3
10
2,4
4,8
7,2
9,6
12
4
10
4,1
6,8
10,3
12,6
16,1
5
10
5,2
8,7
13,3
21,7
26,2
6,25
10
11
23,5
35,6
41,3
50,5
Figure 26
Example recovery time for ≤ 40°C
tPause [s]
IBase Load
[A]
12.2.3 Example: Determining the recovery time
(tPause)
tPause [s]
Use the following tables to determine the required recovery
time (tPause) at the maximum dynamic boost current (IDyn.
Boost) based on the following values:
– IBase Load
– Duration of the boost current (tDyn. Boost)
– Ambient temperature (40 °C or 60 °C)
Required recovery times at ≤ 40°C
12.2.2 Recovery times at an ambient temperature of
60 °C
IDyn. Boost
[A]
1
2
3
4
5
0
10
2,5
4,8
7,3
9,7
12,3
1
10
3
6,4
9,3
12,5
15,4
2
10
3,5
7,8
11,1
13,8
17,3
3
10
4,7
9
13,5
18,5
23
4
10
7,5
13,5
20
26,3
32,1
5
10
23
45
66
80
91
Figure 25
108883_en_00
tPause [s]
tDyn. Boost [s]
IBase Load
[A]
Required recovery times at ≤ 60°C
PHOENIX CONTACT 30 / 48
QUINT4-PS/24DC/24DC/5/PT
13
13.3
SFB Technology
SFB Technology (selective fuse breaking) can be used to
quickly and reliably trip miniature circuit breakers and fuses
connected on the secondary side. In the event of a short
circuit on the secondary side, the power supply supplies up
to 6 times the nominal current for 15 ms. The faulty current
path is switched off selectively.
Loads that are connected in parallel are still supplied with
energy. Operation of these system parts is ensured. In order
to always enable the reliable tripping of circuit breakers and
fuses, certain framework conditions must be observed (see
SFB configuration section).
The U/I Advanced output characteristic curve
supports SFB Technology.
13.1
SFB configuration
Observe the following framework conditions for determining
the maximum distance between the power supply and load:
– The performance class of the power supply
– The cross section of the connecting cable
– The tripping characteristic of the fuse component
Power supply unit
+
+
-
-
Load
l
Figure 28
Schematic diagram of the maximum cable
length
Tripping circuit breakers
I [A]
The circuit breaker is tripped by the high SFB current of the
power supply, typically within 3 to 5 ms. As a result, voltage
dips at loads that are connected in parallel are avoided.
6x IN
typ. 3 - 5 ms
IN
0
Figure 27
13.2
t [s]
SFB pulse trips circuit breakers
Tripping a fuse
Fuses are tripped by melting the predetermined breaking
point inside the fuse capsule. The tripping characteristic of
the fuse is described by the melting integral (I²t). A high
current is crucial in order to achieve a very short tripping
time.
108883_en_00
PHOENIX CONTACT 31 / 48
QUINT4-PS/24DC/24DC/5/PT
13.4
Maximum distance between the power supply and load
The distances given in the table are worst-case values and therefore cover the entire tolerance range for the magnetic tripping
of circuit breakers. The possible distances are often greater in practice.
13.4.1 Thermomagnetic device circuit breaker, type: Phoenix Contact CB TM1 SFB
Maximum distance l [m] with device circuit breaker
Phoenix Contact
CB TM1 1A SFB P
CB TM1 2A SFB P
Conductor cross section
A [mm²]
0.75
1.0
AWG
18
(17)
27
36
10
13
1.5
16
54
20
2.5
14
91
34
The cable lengths determined are based on the following parameters:
Tripping:
DC correction factor (0 Hz):
Characteristics:
Ambient temperature:
Internal resistance Ri of the device circuit
breaker:
Comments:
108883_en_00
magnetic
Phoenix Contact = 1,0
C
Characteristic C (10 times the rated current) x correction factor
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT 32 / 48
QUINT4-PS/24DC/24DC/5/PT
13.4.2 Thermomagnetic circuit breaker, type: Siemens 5SY, ABB S200
Maximum distance l [m] with circuit breaker
Siemens 5SY
A1
A1.6
A2
A3
A4
B2
C1
C1.6
C2
ABB S200
C2
Z1
Z1.6
Z2
Z3
Z4
Conductor cross section
A [mm²]
0.75
1.0
AWG
18
(17)
78
105
58
77
49
65
35
47
20
27
24
33
7
9
3
5
3
4
1
1
64
85
46
62
42
57
30
41
17
23
1.5
16
157
116
98
70
40
49
14
7
6
2
128
93
85
61
34
2.5
14
263
194
164
118
68
82
24
13
10
4
214
156
143
102
57
The cable lengths determined are based on the following parameters:
Tripping:
DC correction factor (0 Hz):
Characteristics:
Ambient temperature:
Internal resistance Ri of the device circuit
breaker:
Comments:
108883_en_00
magnetic
Siemens = 1.4; ABB = 1.5
A, B, C, Z
Characteristic A (3 times the rated current) x correction factor
Characteristic B (5 times the rated current) x correction factor
Characteristic C (10 times the rated current) x correction factor
Characteristic Z (3 times the rated current) x correction factor
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT 33 / 48
QUINT4-PS/24DC/24DC/5/PT
13.4.3 Fuse, type: Cooper Bussmann GMA xA, GMC xA
Maximum distance l [m] with fuse
Cooper Bussmann
GMA 1A
GMA 1.25A
GMA 1.5A
GMA 1.6A
GMA 2A
GMC 1A
GMC 1.25A
Melting integral I²t Conductor cross section
[A²s]
A [mm²]
0.75
1.0
AWG
18
(17)
0.48
48
64
0.84
36
48
1.6
19
25
2
15
20
3.1
9
13
1.8
15
20
3.4
8
11
1.5
16
97
72
38
31
19
31
16
2.5
14
162
120
64
51
33
52
27
The cable lengths determined are based on the following parameters:
Tripping:
Characteristics:
Ambient temperature:
Internal resistance Ri of the fuse:
Comments:
108883_en_00
thermal
Cooper Bussmann GMA (fast-blow - fast acting)
Cooper Bussmann GMC (medium-blow - medium time delay)
+20 °C
taken into consideration
In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
PHOENIX CONTACT 34 / 48
QUINT4-PS/24DC/24DC/5/PT
14
Signaling
14.1
Location and function of the signaling elements
A floating signal contact and two digital outputs are available
for preventive function monitoring of the power supply.
Depending on the configuration of the power supply, either
the two digital outputs or one digital and one analog output
can be selected. The signal outputs are electrically isolated
from the input and output of the power supply.
UOut
29,5V
Five LED status indicators signal the current device status.
The function of each LED status indicator is assigned to a
fixed event.
10
In addition, the power supply can be switched off and on via
an external circuit.
9
8
7
The signal outputs are configured on the software side using
the QUINT POWER software or the QUINT POWER app.
Upon delivery, the power supply is pre-allocated a default
configuration for the signal outputs.
6
Figure 29
24V
Signal
13
14
Rem
SGnd
Out 1
Out 2
1
3.1
3.2
3.3
3.4
3.5
3.6
2
3
4
> 100% Boost
> 75%
> 50% POut
DC OK
UIn < 19,2V
5
Position of signaling elements
Key
No.
1
2
3
4
5
6
7
8
9
10
108883_en_00
Signaling elements
13/14 floating switch contact (N/O contact)
Rem, remote input (switch power supply off and on)
SGnd, signal ground (reference potential for signals
Out 1, Out 2)
Out 1 (digital output, function depends on the signal
option set)
Out 2 (digital or analog output, function depends on
the signal option set)
LED status indicator UIn OK
LED off: UIn > 80 % x UInNom
LED on: UIn 90% x USet
LED flashing: UOut 50% (output power >60 W)
LED status indicator
POut >75% (output power >90 W)
LED status indicator POut >100%, boost mode
(output power >120 W)
PHOENIX CONTACT 35 / 48
QUINT4-PS/24DC/24DC/5/PT
14.1.1 Floating signal contact
14.1.3 Active analog signal output
In the default configuration, the floating switch contact
opens to indicate that the set output voltage has been
undershot by more than 10 % (UOut 50% LED. If the required output power is then
greater than the nominal device power, the power supply
operates in boost mode. In boost mode, the > 100% LED
additionally lights up yellow.
b)
External wiring versions, disable
SLEEP MODE
PHOENIX CONTACT 39 / 48
QUINT4-PS/24DC/24DC/5/PT
14.6
U/I Advanced characteristic curve signaling
The following table shows the standard assignment for signaling for the U/I Advanced characteristic curves which is set by
default.
LED: POut >100 %
Yellow
Signal Out 2: POut < PN
Default
Normal operation
BOOST
Overload operation
Input voltage
POut < PN
POut > PN
UOut < 0.9 x USet
< 0.8 x UN
X
Active High
Active Low
Active Low
X
LED: POut > 75 %
LED: POut > 50 %
X
X
Green
X
LED: DC OK
LED: UIn PN
UOut < 0.9 x USet
< 0.8 x UN
X
Active High
Active Low
Active Low
X
LED: POut > 75 %
LED: POut > 50 %
X
X
Green
X
LED: DC OK
LED: UIn PN
FUSE MODE
I > IFuse for t > tFuse
< 0.8 x UN
X
Active High
Active Low
Active Low
X
X
LED: POut > 75 %
LED: POut > 50 %
Input voltage
X
Green
X
LED: DC OK
LED: UIn 75%
POut
> 50%
PLC
Digital Input
5
6
1
2
3
4
DI x 0/24 V DC
GND
DC OK
UIn
Figure 39
UOut
Schematic diagram, signal wiring with TRABTECH surge protection
Signal
13
14
Rem
SGnd
Out 1
Out 2
> 100% Boost
> 75%
POut
> 50%
DC OK
3.1
3.2
3.3
3.4
3.5
3.6
PLC
Digital Input
A2-
A1+
11/13(+)
A2
11
A1
14
14
DI x 0/24 V DC
GND
12
UIn
Figure 40
108883_en_00
Schematic diagram, signal wiring with relay module
PHOENIX CONTACT 42 / 48
QUINT4-PS/24DC/24DC/5/PT
15
Operating modes
15.2
15.1
Series operation
You can connect several power supplies in parallel in order
to increase the power or to supply the loads redundantly.
To double the output voltage, connect two power supplies in
series. Only use power supplies with the same performance
class and configuration for series operation. If two 24 V DC
power supplies are connected in series, an output voltage of
48 V DC is available to supply the loads.
+
+
-
-
IN
+ −
-48 V
Figure 42
+
-
-
Figure 41
-24 V
+ −
-
+48 V
+
IN
+ −
+
−
+
+24 V
Parallel operation
Σ = IN
Schematic diagram in parallel operation
+
-
Schematic diagrams in series operation
Observe the following points when carrying out parallel
connection:
1. Use power supplies of the same type and performance
class
2. Setting the same output voltages
3. Using the same cable cross sections for wiring
4. Using the same cable lengths for the DC convergence
point
5. Operating power supplies in the same temperature
environment
6. When three or more power supplies are connected in
parallel, each output must be protected (e.g., with
circuit breakers, fuses or decoupling modules)
We recommend the configuration "parallel
operation" for a parallel connection.
For more detailed information on the
operating mode for parallel operation, refer to
the user manual for the QUINT POWER
software or the QUINT POWER app.
108883_en_00
PHOENIX CONTACT 43 / 48
QUINT4-PS/24DC/24DC/5/PT
15.2.1 Redundancy operation
Redundant circuits are suitable for supplying systems and
system parts which place particularly high demands on
operational reliability.
If energy is to be supplied to the load with 1+1 redundancy,
two power supplies of the same type and performance class
must be used. In the event of an error, it must be ensured
that one of the power supplies is able to provide the total
required power for the load. This means that in redundancy
mode, two 5 A power supplies supply a load with a nominal
current of 5 A, for example. During normal operation of the
power supplies, each power supply therefore supplies
2.5 A.
Always use cables with the same cross sections and lengths
when wiring the power supplies on the DC output side.
Redundancy modules can be used to 100% decouple two
power supplies from one another and to ensure the supply.
A distinction is made here between passive and active
redundancy modules. Optimum decoupling with
simultaneous monitoring and minimal power dissipation can
be achieved with the QUINT ORING or QUINT S-ORING
active redundancy module.
IN
Certain specifications apply in redundancy operation with
regard to the configuration of the keepout areas. In
redundancy operation, the power supplies are operated with
maximum half the nominal power. The keepout areas are
therefore reduced.
Using the signaling settings, you can monitor whether both
power supplies are being operated with ≤ half the nominal
load. In the case of system extension, an overload is
prevented if one of the power supplies fails.
15.2.2 Increased power
When n power supplies are connected in parallel, the output
current is increased to n x IN. Parallel connection for
increased power is used when extending existing systems.
If the individual power supply does not cover the current
consumption of the most powerful load, parallel connection
of power supplies is recommended.
When three or more power supplies are
connected in parallel, each output must be
protected separately, e.g., by a circuit
breaker, fuse or decoupling module such as
QUINT ORING, QUINT S-ORING or
QUINT DIODE.
IN
+ −
+ −
IN
IN
+ –
+ –
+
−
+
–
Σ = IN
+ −
Figure 43
Schematic diagram, redundant operation with
QUINT ORING
+ –
Figure 45
IN
IΣ= 2 x IN
Schematic diagram of increased performance
IN
+ −
+ −
+
−
Σ = IN
Figure 44
108883_en_00
Schematic diagram, redundant operation with
QUINT S-ORING
PHOENIX CONTACT 44 / 48
QUINT4-PS/24DC/24DC/5/PT
16.3
Derating
The QUINT POWER power supply runs in nominal
operation without any limitations. For operation outside the
nominal range, the following points should be observed
depending on the type of use.
16.1
Ambient temperature
POut [W]
When operating the power supply at an ambient
temperature of > 60 °C, a power derating of 2.5 %/K should
be observed. Up to an ambient temperature of 40 °C, the
power supply can take power from the static boost for a
sustained period. In the 40 °C to 60 °C temperature range,
the power supply can output more than the nominal power
for a sustained period.
PDyn. Boost
200%
PStat. Boost
PN
125%
100%
75%
-25
40
60
Installation height
The power supply can be operated at an installation height
of up to 2000 m without any limitations. Different data
applies for installation locations above 2000 m due to the
differing air pressure and the reduced convection cooling
associated with this (see technical data section). The data
provided is based on the results of pressure chamber testing
performed by an accredited test laboratory.
POut [%]
16
225
200
175
150
125
100
75
50
25
0
0
= PN 100 % 60 °C
= PStat. 125 % 40 °C
= PDyn. 200 % 60 °C
1000
2000
3000
4000
5000
H [m]
Figure 47
Output power depending on the installation
height
70
TA [°C]
Figure 46
16.2
Output power depending on the ambient
temperature
Input voltage
UIn
700%
> 55% B oo
DC0% P st
U OK out
In
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
40
50
60
Y
70
T [°C]
Z
X
POut [%]
16.4.2 Rotated mounting position 90° Z-axis
QU
INT
R
UOut
Signal
13
3.1
14
3.2
3.3
Rem
SGnd
3.4
Out 1
3.5
3.6
Out 2
> 100% Boost
> 75%
> 50% Pout
DC OK
UIn
Y
PO
WE
Ord
.N
o.x
xx
xx
xx
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
40
50
60
70
T [°C]
Z
X
108883_en_00
PHOENIX CONTACT 46 / 48
QUINT4-PS/24DC/24DC/5/PT
POut [%]
16.4.3 Rotated mounting position 180° Z-axis
QUINT POWER
3.1
3.2
3.3
3.4
>1
3.5
> 700%
3
> 55% Bo .6
DC0% P ost
U OK Out
In
13
14
Re
m
SG
n
Ou d
t
Ou 1
t2
Sig
na
l
Out
Y
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
40
50
60
70
T [°C]
U
Ord.No.xxxxxxx
Z
X
xx
xxx
o.x
x
UIn
.N
QU
INT
P
OW
E
R
Ord
Y
> 100% Boost
> 75% Pout
> 50%
DC OK
Signal
UOut
3.1
13
14
3.2
3.3
Rem
3.4
SGnd
Out 1
3.5
Out 2
3.6
POut [%]
16.4.4 Rotated mounting position 270° Z-axis
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
40
50
60
70
T [°C]
Z
X
108883_en_00
PHOENIX CONTACT 47 / 48
QUINT4-PS/24DC/24DC/5/PT
UO
Q
U
IN
T
P
O
W
E
R
O
rd
.N
o.
2
90
46
xx
16.4.5 Rotated mounting position 90° X-axis
S
l
m
na
14
ig
13
1
3. 2
3. 3
3. 4
3.
5
3. 6
3.
U
POut [%]
ut
e
R nd
st
G 1
oo
S ut 2
B t
O t
u
ou
O
0% P
10 %
> 75 0% K
> 5 O
> C
D In
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
40
50
60
70
T [°C]
Y
Z
X
POut [%]
16.4.6 Rotated mounting position 270° X-axis
225
200
175
150
125
100
75
50
25
0
-25
= PN 100 %
= PStat. 125 %
= PDyn. 200 %
0
10
20
30
Y
40
50
60
70
T [°C]
Z
X
108883_en_00
PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany
phoenixcontact.com
48 / 48
工商网监
湘ICP备2023018690号
