2952185

https://www.phoenixcontact.com/us/products/2952185 Relay Module - EMG 45-REL/IR-W230/HWR - 2952185 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Relay module, with soldered-in industrial relay, contact: 2 PDTs, for multi-input fault warnings, with input diode array in P polarity (6 diodes 1N4007) and capacitor parallel to the coil as well as a multi-input light indicator, input voltage 230 V AC The illustration shows version EMG 45-REL/IR-G 24/HWR     Key commercial data Packing unit 1 pc GTIN Weight per Piece (excluding packing) 130.64 GRM Custom tariff number 85364900 Country of origin Germany Technical data Dimensions Width 45 mm Height 75 mm Depth 82.5 mm Ambient conditions Ambient temperature (operation) -20 °C ... 50 °C Ambient temperature (storage/transport) -20 °C ... 70 °C Coil side Nominal input voltage UN 230 V AC Input voltage range in reference to UN 0.9 ... 1.1 Typical input current at UN approx. 16 mA 10/22/2014   Page 1 / 4 https://www.phoenixcontact.com/us/products/2952185 Relay Module - EMG 45-REL/IR-W230/HWR - 2952185 Technical data Coil side Typical response time 5 ms ... 15 ms Typical release time range 15 ms ... 25 ms Coil resistance 19.5 kΩ Nominal power consumption approx. 1 VA Operating voltage display LED red Protective circuit Decoupling diodes Decoupling diodes Capacitor Capacitor Diode type 1 N 4007 Max. operating voltage of diodes 250 V AC Peak reverse voltage per diode 1300 V Reverse current per diode 30 µA Conducting state voltage per diode approx. 0.8 V Conducting state current per diode 0.7 A (with single load) 0.2 A (with simultaneous loads) Contact side Contact type Single contact, 2-PDT Contact material AgNi Maximum switching voltage 250 V AC 110 V DC Maximum inrush current 5A Limiting continuous current 3A Interrupting rating (ohmic load) max. 750 VA General Type of note Notes on operation Note During installation, the system must be connected in phase. Test voltage relay winding/relay contact 2 kV AC (50 Hz, 1 min.) Mechanical service life > 10 cycles Standards/regulations DIN VDE 0110b, Gr. C for 250 V DC 7 DIN EN 50178/DIN VDE 0160 (in relevant parts) Pollution degree 2 Surge voltage category II Mounting position any Assembly instructions In rows with zero spacing Connection data Connection method Screw connection Stripping length 8 mm 10/22/2014   Page 2 / 4 https://www.phoenixcontact.com/us/products/2952185 Relay Module - EMG 45-REL/IR-W230/HWR - 2952185 Technical data Connection data Conductor cross section stranded min. 0.2 mm² Conductor cross section stranded max. 2.5 mm² Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 4 mm² Conductor cross section AWG/kcmil max 12 Conductor cross section AWG/kcmil min. 24 Screw thread M3 Classifications eCl@ss eCl@ss 4.0 27371102 eCl@ss 4.1 27371102 eCl@ss 5.0 27371001 eCl@ss 5.1 27371001 eCl@ss 6.0 27371001 eCl@ss 7.0 27371001 eCl@ss 8.0 27371001 ETIM ETIM 2.0 EC000196 ETIM 3.0 EC000196 ETIM 4.0 EC000196 ETIM 5.0 EC000196 UNSPSC UNSPSC 6.01 30211916 UNSPSC 7.0901 39121515 UNSPSC 11 39121515 UNSPSC 12.01 39121515 UNSPSC 13.2 39121515 Drawings 10/22/2014   Page 3 / 4 https://www.phoenixcontact.com/us/products/2952185 Relay Module - EMG 45-REL/IR-W230/HWR - 2952185 Circuit diagram Phoenix Contact 2014 © - all rights reserved http://www.phoenixcontact.com 10/22/2014   Page 4 / 4