2966799

PLC-OS…/SEN PLC INTERFACE With Solid-State Relay, Sensor Version INTERFACE Data Sheet 103152_en_01 1 © PHOENIX CONTACT - 03/2008 Description In applications as the interface between the PLC and sensors (e.g., proximity switches, limit switches or auxiliary contacts), as a rule only one N/O contact is required. In this case, the PLC-OS…/SEN input module can be used, which is specially optimized for these applications and consists of a 6.2 mm basic terminal block and plug-in miniature solidstate relay with screw or spring-cage connection. 1.1 No Need for Power Terminal Blocks Unlike conventional input relays, all sensor connections, including the supply voltage for the sensors and switches, are connected directly to the PLC INTERFACE module. The PLC-OS…/SEN can thus be used directly as a terminal strip with integrated interface function for the incoming sensor cables, without the need for additional modular terminal blocks (see also INTERFACE catalog). – Elimination of the need for modular terminal blocks for the sensor/switch supply, signal, and sensor ground – Space savings of around 80% – Time saving of around 60% – Reduction in wiring due to plug-in bridges 1.2 Optimum Use of Plug-In Bridges The PLC INTERFACE module achieves maximum efficiency with the user-friendly FBST plug-in bridge system. The PLC-OS…/SEN makes effective use of the bridging options for the power supply for sensors/switches, for the supply/sensor ground at the A2 connection, and for the common supply potential of the PLC at connection 13. Especially effective here are the 500 mm long colorinsulated continuous plug-in bridges that can easily be cut to the required length and quickly inserted in the bridge shafts. They eliminate the need for complicated and timeconsuming loop bridges – the reduction in wiring by eliminating the need for modular terminal blocks and the use of all bridging options is around 60%. 1.3 – – – – – – – – Additional Advantages Switching power of up to 24 V DC/3 A, depending on the type IP67-protected fully encapsulated optical electronics Available with input or power solid-state relays as an option Integrated input circuit Solid-state relay can be replaced using an engagement lever Wear-resistant switching Resistant to vibrations and shocks Inflammability class V0 according to UL94 Make sure you always use the latest documentation. It can be downloaded at www.download.phoenixcontact.com. A conversion table is available on the Internet at www.download.phoenixcontact.com/general/7000_en_00.pdf. This data sheet is valid for all products listed on the following page: PLC-OS…/SEN 2 Ordering Data PLC INTERFACE With Solid-State Relay, Sensor Version Description Type PLC INTERFACE, comprising PLC-BSC...SEN basic terminal block and plug-in solid-state relay (see INTERFACE catalog), with screw connection, for mounting on 3 PLC INTERFACE, comprising PLC-BSP...SEN basic terminal block and plug-in solid-state relay (see INTERFACE catalog), with spring-cage connection, for mounting on 3 1 Order No. Pcs./Pck. 2966773 10 120 V AC/110 V DC PLCOSC-120UC/48DC/100/SEN 2966799 10 230 V AC/220 V DC1 PLCOSC-230UC/48DC/100/SEN 2966809 10 2967578 10 120 V AC/110 V DC PLCOSP-120UC/48DC/100/SEN 2967581 10 230 V AC/220 V DC1 PLCOSP-230UC/48DC/100/SEN 2967594 10 24 V DC PLCOSC- 24DC/48DC/100/SEN 24 V DC PLCOSP- 24DC/48DC/100/SEN The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. With the 120 V and 230 V modules, an OPT-60DC/... 60 V solid-state relay is normally used due to the input circuit integrated in the basic terminal block. For the protection of input and output, inductive loads must be dampened with an effective protective circuit. Accessories Description Type Order No. Pcs./Pck. Insulating plate PLC-ATP BK 2966841 25 The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for potential bridging) and for safe isolation between adjacent modules. For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INTERFACE catalog or www.phoenixcontact.com. 3 Technical Data Input Data ...24DC... ...120UC... ...230UC... 24 V DC 120 V AC/110 V DC 230 V AC/220 V DC Nominal input voltage Permissible range (with reference to UN) 0.8 ... 1.2 x UN 0.8 ... 1.1 x UN 1 signal ("H") 0.8 x UN 0.8 x UN 0 signal ("L") 0.4 x UN 0.3 x UN Switching level Typical input current at UN 8 mA Typical response time at UN 20 μs 6 ms Typical release time at UN 300 μs 10 ms Transmission frequency flimit 300 Hz 10 Hz Yellow LED, protection against polarity reversal, free-wheeling diode Yellow LED, bridge rectifier Input circuit 4 mA 3 ms 5 ms Output Data Maximum switching voltage 48 V DC Minimum switching voltage 3 V DC Limiting continuous current 100 mA Output configuration 2-wire floating Output circuit Protection against polarity reversal, surge protection Voltage drop at maximum limiting continuous current ≤1V 103152_en_01 PHOENIX CONTACT 2 PLC-OS…/SEN General Data Impulse voltage withstand level 2.5 kV, 50 Hz, 1 min. Ambient temperature range Operation -25°C ... 60°C (230 V type 20°C ... 55°C) Storage/transport -40°C ... 85°C Nominal operating mode 100% operating factor Inflammability class according to UL 94 (housing) V0 Standards/specifications1 IEC 60664, IEC 60664 A, DIN VDE 0110 (basic insulation) Pollution degree 2 Surge voltage category III Mounting position Any Mounting Can be aligned without spacing Conductor cross-section Solid, with screw connection 0.14 mm2 ... 2.5 mm2 (26 - 14 AWG) Stranded, with screw connection 0.14 mm2 ... 1.5 mm2 (26 - 14 AWG) Solid, with spring-cage connection 0.2 mm2 ... 2.5 mm2 (24 - 14 AWG) Stranded, with spring-cage connection 0.2 mm2 ... 1.5 mm2 (24 - 14 AWG) Stripping length Screw connection 10 mm Spring-cage connection 8 mm Dimensions (W x H x D) 6.2 mm x 94 mm x 80 mm Housing material Polyamide PA, green 1 The PLC-ATP BK insulating plate must be installed for safe isolation between adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. Tests/Approvals c Uu F CE UL GL Block Diagram 5 Load current [A] 4 13+ A2 14 BB Derating Curve 3 2 1 1) A1 1) 103152_en_01 The input circuit depends on the type 0 0 10 20 30 40 50 60 Ambient temperature [°C] PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49 - 52 35 - 30 0 PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300 www.phoenixcontact.com 3