2980665

PLC-OS…/300DC/1 PLC INTERFACE With Integrated Solid-State Relay INTERFACE Data Sheet 102491_en_04 1 © PHOENIX CONTACT 2010-12-22 Description The 6.2 mm PLC-OS…/300DC/1 PLC INTERFACE module with screw or spring-cage connection has an integrated solid-state relay. 1.1 Input Voltages From 5 V to 230 V PLC-OS…/300DC/1 is available on the control side in all common industrial voltages from 5 V to 230 V. A further advantage is the ready-integrated input circuit. It consists of a status indicator and polarity reversal protection function, and ensures that the operating state is displayed clearly, also preventing destruction of the optical electronics should the polarity be accidentally reversed. 1.2 Plug-In Bridges Save Wiring The PLC INTERFACE module achieves maximum efficiency with the user-friendly FBST plug-in bridge system. PLC-OS…/300DC/1 makes effective use of the bridging options for the A1/A2 connection on the control side and for the supply at connection 13 on the load side. Especially efficient here are the 500 mm long color-insulated continuous plug-in bridges that can easily be cut to the required length and quickly inserted in the bridge shafts. They eliminate the need for complicated and timeconsuming loop bridges. 1.3 – – – – – Additional Advantages Switching power of up to 300 V DC/1 A Wear-resistant switching Integrated protective circuit Resistant to vibrations and shocks 4 kVrms electrical isolation between input and output Make sure you always use the latest documentation. It can be downloaded at www.phoenixcontact.net/download. This data sheet is valid for all products listed on the following page: PLC-OS…/300DC/1 2 Ordering Data PLC INTERFACE With Screw Connection, Housing Open on One Side Description Type Order No. PLC INTERFACE with integrated solid-state relay 5 V DC PLC-OSC-5DC/300DC/1 2980652 10 PLC INTERFACE with integrated solid-state relay 12 V DC PLC-OSC-12DC/300DC/1 2980665 10 Pcs./Pck. PLC INTERFACE with integrated solid-state relay 24 V DC PLC-OSC-24DC/300DC/1 2980678 10 PLC INTERFACE with integrated solid-state relay 48 V DC ... 60 V DC PLC-OSC-60DC/300DC/1 2980681 10 PLC INTERFACE with integrated solid-state relay 110 V DC PLC-OSC-110DC/300DC/1 2980694 10 PLC INTERFACE with integrated solid-state relay 125 V DC PLC-OSC-125DC/300DC/1 2982210 10 PLC INTERFACE with integrated solid-state relay 220 V DC PLC-OSC-220DC/300DC/1 2980704 10 PLC INTERFACE with integrated solid-state relay 120 V AC PLC-OSC-120AC/300DC/1 2980717 10 PLC INTERFACE with integrated solid-state relay 230 V AC1 PLC-OSC-230AC/300DC/1 2980720 10 PLC INTERFACE With Spring-Cage Connection, Housing Open on One Side Description Type Order No. Pcs./Pck. PLC INTERFACE with integrated solid-state relay 5 V DC PLC-OSP-5DC/300DC/1 2980814 10 PLC INTERFACE with integrated solid-state relay 12 V DC PLC-OSP-12DC/300DC/1 2980827 10 PLC INTERFACE with integrated solid-state relay 24 V DC PLC-OSP-24DC/300DC/1 2980830 10 PLC INTERFACE with integrated solid-state relay 48 V DC ... 60 V DC PLC-OSP-60DC/300DC/1 2980843 10 PLC INTERFACE with integrated solid-state relay 110 V DC PLC-OSP-110DC/300DC/1 2980856 10 PLC INTERFACE with integrated solid-state relay 125 V DC PLC-OSP-125DC/300DC/1 2982223 10 PLC INTERFACE with integrated solid-state relay 220 V DC PLC-OSP-220DC/300DC/1 2980869 10 PLC INTERFACE with integrated solid-state relay 120 V AC PLC-OSP-120AC/300DC/1 2980872 10 PLC INTERFACE with integrated solid-state relay 230 V AC1 PLC-OSP-230AC/300DC/1 2980885 10 1 The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. For the protection of input and output, inductive loads must be dampened with an effective protective circuit. Accessories Description Type Order No. Pcs./Pck. Insulating plate PLC-ATP BK 2966841 25 The PLC-ATP BK insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (FBST 8-PLC... or FBST 500... can be used for potential bridging) and for safe isolation between adjacent modules. For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INTERFACE catalog or www.phoenixcontact.com. 102491_en_04 PHOENIX CONTACT 2 PLC-OS…/300DC/1 3 Technical Data Input Data Nominal input voltage1 DC 5 V DC 12 V DC 24 V DC Permissible range (with reference to UN) 48 ... 60 V DC AC 110 V DC 125 V DC 220 V DC 120 V AC 230 V AC 0.8 ... 1.2 x UN 0.8 ... 1.1 x UN 1 signal ("H") ≥ 0.8 x UN ≥ 0.8 x UN 0 signal ("L") ≤ 0.4 x UN Switching level Typical input current at UN ≤ 0.4 x UN 5 mA 6 mA 8 mA 5 mA 5 mA 6 mA 3 mA 3 mA 3 mA Typical response time at UN 800 µs 300 µs 300 µs 300 µs 400 µs 400 µs 400 µs 19 ms 19 ms Typical release time at UN 1.5 ms 800 µs 700 µs 700 µs 700 µs 700 µs 1.4 ms 6 ms Transmission frequency flimit Input circuit 1 6 ms 50 Hz 50 Hz Yellow LED, polarity protection, surge protection Yellow LED, surge protection, bridge rectifier The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. Output Data Nominal output voltage range1 12 V DC ... 300 V DC Limiting continuous current 1 A (see "Derating Curve" on page 4) Output configuration 2-wire floating Output circuit Protection against polarity reversal, surge protection Voltage drop at maximum limiting continuous current < 500 mV 1 The PLC-ATP BK insulating plate must be installed for voltages greater than 250 V (L1, L2, L3) between the same terminal points on adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. General Data Rated insulation voltage 300 V Impulse voltage withstand level 4 kV, 50 Hz, 1 minute Ambient temperature range -20°C ... 60°C Nominal operating mode 100% operating factor Inflammability class according to UL 94 (housing) V0 Air and creepage distances between the circuits1 DIN EN 50178 (basic insulation) Pollution degree 2 Surge voltage category III Mounting position Any Assembly Can be aligned without spacing Conductor cross section Screw connection 0.14 mm2 ... 2.5 mm2 Spring-cage connection 0.2 mm2 ... 2.5 mm2 Stripping length 8 mm Dimensions (W x H x D) 6.2 mm x 86 mm x 80 mm Housing material Polybutylene terephthalate PBT non-reinforced, green 1 The PLC-ATP BK insulating plate must be installed for safe isolation between adjacent modules (see "Accessories"). FBST 8-PLC... or FBST 500... is then used for potential bridging. Tests/Approvals CE c UL Applied for CUL Applied for GL Applied for 102491_en_04 PHOENIX CONTACT 3 PLC-OS…/300DC/1 Block Diagram 5 A1 14 14 A2 13+ A2 13+ Derating Curve Load current [A] 4 1 0,7 0 1 30 40 50 60 Ambient temperature [°C] 1 For input voltages of 220 V DC and 230 V AC 102491_en_04 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany • Phone: +49-(0) 5235-3-00 PHOENIX CONTACT • P.O.Box 4100 • Harrisburg • PA 17111-0100 • USA • Phone: +717-944-1300 www.phoenixcontact.com 4