https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
Test disconnect terminal block, cross section: 0.1 - 6 mm², AWG: 26 - 8, width 13 mm, color: gray
Your advantages
Easy grouping of flange terminal blocks
Flange terminal blocks for direct mounting in control boxes
Key Commercial Data
Packing unit
1 pc
Minimum order quantity
50 pc
GTIN
GTIN
4046356500302
Weight per Piece (excluding packing)
36.000 g
Custom tariff number
85369010
Country of origin
India
Technical data
General
Number of levels
1
Number of connections
2
Potentials
1
Nominal cross section
10 mm²
Color
gray
Insulating material
PA
Flammability rating according to UL 94
V0
09/10/2019 Page 1 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Technical data
General
Rated surge voltage
8 kV
Degree of pollution
3
Overvoltage category
III
Insulating material group
I
Maximum power dissipation for nominal condition
1.82 W
Designation
Level 1 above 1 below 1
Maximum load current
50 A (with 10 mm² conductor cross section)
Nominal current IN
50 A
Nominal voltage UN
800 V (with open 630 V disconnect point)
Open side panel
Yes
Shock protection test specification
IEC 60529:2001-02
Back of the hand protection
guaranteed
Result of surge voltage test
Test passed
Surge voltage test setpoint
7.3 kV
Result of power-frequency withstand voltage test
Test passed
Power frequency withstand voltage setpoint
1.89 kV
Result of the test for mechanical stability of terminal points (5 x conductor
connection)
Test passed
Result of tight fit on support
Test passed
Tight fit on carrier
NS 32/NS 35
Setpoint
5N
Result of voltage-drop test
Test passed
Requirements, voltage drop
≤ 6,4 mV
Result of temperature-rise test
Test passed
Short circuit stability result
Test passed
Conductor cross section short circuit testing
6 mm²
Short-time current
0.72 kA
Conductor cross section short circuit testing
10 mm²
Short-time current
1.2 kA
Result of thermal test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Oscillation, broadband noise test result
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test spectrum
Service life test category 2, bogie-mounted
Test frequency
f1 = 5 Hz to f2 = 250 Hz
ASD level
6.12 (m/s ) /Hz
Acceleration
3.12 g
2 2
09/10/2019 Page 2 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Technical data
General
Test duration per axis
5h
Test directions
X-, Y- and Z-axis
Shock test result
Test passed
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Shock form
Half-sine
Acceleration
30g
Shock duration
18 ms
Number of shocks per direction
3
Test directions
X-, Y- and Z-axis (pos. and neg.)
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21)) 130 °C
Static insulating material application in cold
-60 °C
Behavior in fire for rail vehicles (DIN 5510-2)
Test passed
Flame test method (DIN EN 60695-11-10)
V0
Oxygen index (DIN EN ISO 4589-2)
>32 %
NF F16-101, NF F10-102 Class I
2
NF F16-101, NF F10-102 Class F
2
Surface flammability NFPA 130 (ASTM E 162)
passed
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Dimensions
Width
13 mm
End cover width
2.2 mm
Length
79.9 mm
Height NS 35/7,5
49.8 mm
Height NS 35/15
57.3 mm
Height NS 32
54.8 mm
Pitch
13 mm
Connection data
Note
Connection bolts
Connection
1 level
09/10/2019 Page 3 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Technical data
Connection data
Connection method
Bolt connection
Screw thread
M5
Tightening torque, min
2 Nm
Tightening torque max
2.2 Nm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible min.
0.1 mm²
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
26
Max. AWG conductor cross section, flexible
8
Cable lug connection according to standard
DIN 46234
Min. cross section for cable lug connection
0.1 mm²
Max. cross section for cable lug connection
10 mm²
Hole diameter, min.
5.3 mm
Cable lug width, max.
10 mm
Bolt diameter
5 mm
Cable lug connection according to standard
DIN 46237
Min. cross section for cable lug connection
0.5 mm²
Max. cross section for cable lug connection
6 mm²
Hole diameter, min.
5.3 mm
Cable lug width, max.
10 mm
Bolt diameter
5 mm
Standards and Regulations
Connection in acc. with standard
UL
IEC 60947-7-1
Flammability rating according to UL 94
V0
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Environmental Product Compliance
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”, Category
“Manufacturer's declaration”
Drawings
09/10/2019 Page 4 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Circuit diagram
Classifications
eCl@ss
eCl@ss 4.0
27141100
eCl@ss 4.1
27141100
eCl@ss 5.0
27141100
eCl@ss 5.1
27141100
eCl@ss 6.0
27141100
eCl@ss 7.0
27141126
eCl@ss 8.0
27141126
eCl@ss 9.0
27141126
ETIM
ETIM 2.0
EC000902
ETIM 3.0
EC000902
ETIM 4.0
EC000902
ETIM 5.0
EC000902
ETIM 6.0
EC000902
ETIM 7.0
EC000902
UNSPSC
UNSPSC 6.01
30211811
UNSPSC 7.0901
39121410
UNSPSC 11
39121410
UNSPSC 12.01
39121410
UNSPSC 13.2
39121410
Approvals
Approvals
09/10/2019 Page 5 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Approvals
Approvals
UL Recognized / EAC
Ex Approvals
Approval details
UL Recognized
http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm
B
C
Nominal voltage UN
600 V
600 V
Nominal current IN
45 A
45 A
EAC
FILE E 60425
RU CDE.A*30.B.01742
Accessories
Accessories
Cover profile
Cover profile - AP RSC-T - 3059139
Cover profile, for covering terminal strips, directly snapped onto RBO... and RSC... test disconnect terminal blocks.
Length supplied: 1 m
DIN rail
DIN rail perforated - NS 35/ 7,5 PERF 2000MM - 0801733
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
09/10/2019 Page 6 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
DIN rail, unperforated - NS 35/ 7,5 UNPERF 2000MM - 0801681
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail perforated - NS 35/ 7,5 WH PERF 2000MM - 1204119
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized, white
passivated, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/ 7,5 WH UNPERF 2000MM - 1204122
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/ 7,5 AL UNPERF 2000MM - 0801704
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Aluminum, uncoated,
length: 2000 mm, color: silver
DIN rail perforated - NS 35/ 7,5 ZN PERF 2000MM - 1206421
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
09/10/2019 Page 7 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
DIN rail, unperforated - NS 35/ 7,5 ZN UNPERF 2000MM - 1206434
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/ 7,5 CU UNPERF 2000MM - 0801762
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
End cap - NS 35/ 7,5 CAP - 1206560
DIN rail end piece, for DIN rail NS 35/7.5
DIN rail perforated - NS 35/15 PERF 2000MM - 1201730
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/15 UNPERF 2000MM - 1201714
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
09/10/2019 Page 8 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
DIN rail perforated - NS 35/15 WH PERF 2000MM - 0806602
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/15 WH UNPERF 2000MM - 1204135
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, Galvanized,
white passivated, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/15 AL UNPERF 2000MM - 1201756
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated - NS 35/15 ZN PERF 2000MM - 1206599
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/15 ZN UNPERF 2000MM - 1206586
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
length: 2000 mm, color: silver
09/10/2019 Page 9 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
DIN rail, unperforated - NS 35/15 CU UNPERF 2000MM - 1201895
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
End cap - NS 35/15 CAP - 1206573
DIN rail end piece, for DIN rail NS 35/15
DIN rail, unperforated - NS 35/15-2,3 UNPERF 2000MM - 1201798
DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
End block
End clamp - CLIPFIX 35 - 3022218
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, width: 9.5 mm, color: gray
End clamp - CLIPFIX 35-5 - 3022276
Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, with parking option for
FBS...5, FBS...6, KSS 5, KSS 6, width: 5.15 mm, color: gray
09/10/2019 Page 10 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
End clamp - E/NS 35 N - 0800886
End clamp, width: 9.5 mm, color: gray
End clamp - E/UK - 1201442
End clamp, width: 9.5 mm, height: 35.3 mm, material: PA, length: 50.5 mm, Mounting on a DIN rail NS 32 or NS 35,
color: gray
End clamp - E/UK 1 - 1201413
End clamps, for supporting the ends of double-level and three-level terminal blocks, width: 10 mm, color: gray
End cover
End cover - D-RSC 5-T - 3058046
End cover, length: 80.9 mm, width: 2.2 mm, height: 39.7 mm, color: gray
Labeled terminal marker
Zack marker strip - ZB 13 CUS - 0829132
Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap into
tall marker groove, for terminal block width: 13 mm, lettering field size: 13 x 10.5 mm, Number of individual labels: 5
09/10/2019 Page 11 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
Zack Marker strip, flat - ZBF 13 CUS - 0829134
Zack Marker strip, flat, can be ordered: Strip, white, labeled according to customer specifications, mounting type: snap
into flat marker groove, for terminal block width: 13 mm, lettering field size: 13 x 5.2 mm, Number of individual labels: 5
Partition plate
Separating plate - TS-KK 3 - 2770215
Separating plate, length: 14 mm, width: 0.5 mm, height: 16 mm, color: gray
Separating plate - TS-UT 6-T/SP - 3072821
Separating plate, length: 105.2 mm, width: 1 mm, height: 67.5 mm, color: gray
Screw bridge
Fixed bridge - FB 10-13 - 3059126
Fixed bridge, pitch: 13 mm, number of positions: 10, color: silver
09/10/2019 Page 12 / 13
https://www.phoenixcontact.com/us/products/3058172
Test disconnect terminal block - RSC 5-T - 3058172
Accessories
Fixed bridge - FB 10-13 ISO - 3059663
Fixed bridge, pitch: 13 mm, number of positions: 10, color: silver
Screwdriver tools
Screwdriver - SZG 0,9X6,5 VDE - 1205134
Screwdriver, slot-headed, graded, for test socket screws, size: 0.9 x 6.5 x 175 mm, 2-component grip, with non-slip grip
Terminal marking
Zack marker strip - ZB 13:UNBEDRUCKT - 0829131
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type: snap
into tall marker groove, for terminal block width: 13 mm, lettering field size: 13 x 10.5 mm, Number of individual labels: 5
Zack Marker strip, flat - ZBF 13:UNBEDRUCKT - 0829133
Zack Marker strip, flat, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into flat marker groove, for terminal block width: 13 mm, lettering field size: 13 x 5.2 mm, Number of individual
labels: 5
Phoenix Contact 2019 © - all rights reserved
http://www.phoenixcontact.com
09/10/2019 Page 13 / 13