3232011

https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Feed-through terminal block, With test socket screws for insertion of test plugs, Connection method: Screw connection, Cross section: 0.2 mm² - 6 mm², AWG: 24 - 10, Width: 6.2 mm, Color: gray, Mounting type: NS 35/7,5, NS 35/15, NS 32 Why buy this product  The four-conductor connection enables user-friendly wiring  The constant circuits common in process automation transmit the measured values as a load-independent current of 0 - 20 mA  The lower level is assigned to the measuring line while the upper level is used for voltage pick-off via the 249 Ohm resistor  A voltage signal pick-off can be implemented in the measuring line using this terminal block, enabling the signal to be used as an analog signal for process computers Key Commercial Data Packing unit 1 STK Minimum order quantity 50 STK Weight per Piece (excluding packing) 15.600 g Custom tariff number 85369010 Country of origin Poland Technical data Environmental Product Compliance China RoHS Hazardous substances above threshold values; Environmentally Friendly Use Period = 50; For details go to tab “Downloads”, Category “Manufacturer's declaration” General Number of levels 1 Number of connections 4 Nominal cross section 4 mm² 09/01/2016   Page 1 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Technical data General Color gray Insulating material PA Flammability rating according to UL 94 V2 Rated surge voltage 6 kV Degree of pollution 3 Overvoltage category III Insulating material group I Connection method Screw connection Connection in acc. with standard IEC 60947-7-1 Maximum load current 10 mA (the current is determined by the component used) Nominal current IN 32 A (the current is determined by the component used) Nominal voltage UN 630 V Open side panel Yes Dimensions Width 6.2 mm Length 63.5 mm Height NS 35/7,5 47 mm Height NS 35/15 54.5 mm Height NS 32 52 mm End cover width 1.5 mm Connection data Connection method Screw connection Connection in acc. with standard IEC 60947-7-1 Screw thread M3 Tightening torque, min 0.5 Nm Tightening torque max 0.6 Nm Stripping length 8 mm Conductor cross section solid min. 0.2 mm² Conductor cross section solid max. 6 mm² Conductor cross section AWG min. 24 Conductor cross section AWG max. 10 Conductor cross section flexible min. 0.2 mm² Conductor cross section flexible max. 4 mm² Min. AWG conductor cross section, flexible 24 Max. AWG conductor cross section, flexible 10 Conductor cross section flexible, with ferrule without plastic sleeve min. 0.25 mm² 09/01/2016   Page 2 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Technical data Connection data Conductor cross section flexible, with ferrule without plastic sleeve max. 4 mm² Conductor cross section flexible, with ferrule with plastic sleeve min. 0.25 mm² Conductor cross section flexible, with ferrule with plastic sleeve max. 1.5 mm² Cross section with insertion bridge, solid max. 2.5 mm² Cross section with insertion bridge, stranded max. 2.5 mm² 2 conductors with same cross section, solid min. 0.2 mm² 2 conductors with same cross section, solid max. 1 mm² 2 conductors with same cross section, stranded min. 0.2 mm² 2 conductors with same cross section, stranded max. 1.5 mm² 2 conductors with same cross section, stranded, ferrules without plastic sleeve, min. 0.25 mm² 2 conductors with same cross section, stranded, ferrules without plastic sleeve, max. 1.5 mm² 2 conductors with same cross section, stranded, TWIN ferrules with plastic 0.5 mm² sleeve, min. 2 conductors with same cross section, stranded, TWIN ferrules with plastic 1 mm² sleeve, max. Nominal current IN 32 A (the current is determined by the component used) Maximum load current 10 mA (the current is determined by the component used) Nominal voltage UN 630 V Internal cylindrical gage A4 Standards and Regulations Connection in acc. with standard IEC 60947-7-1 Flammability rating according to UL 94 V2 Classifications eCl@ss eCl@ss 4.0 27141120 eCl@ss 4.1 27141120 eCl@ss 5.0 27141120 eCl@ss 5.1 27141120 eCl@ss 6.0 27141120 eCl@ss 7.0 27141120 eCl@ss 8.0 27141120 eCl@ss 9.0 27141120 09/01/2016   Page 3 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Classifications ETIM ETIM 2.0 EC000897 ETIM 3.0 EC000897 ETIM 4.0 EC000897 ETIM 5.0 EC000897 UNSPSC UNSPSC 6.01 30211811 UNSPSC 7.0901 39121410 UNSPSC 11 39121410 UNSPSC 12.01 39121410 UNSPSC 13.2 39121410 Approvals Approvals Approvals EAC Ex Approvals Approval details EAC   EAC-Zulassung Accessories Accessories DIN rail DIN rail perforated - NS 32 PERF 2000MM - 1201002 G-profile DIN rail, material: Steel, perforated, height 15 mm, width 32 mm, length 2 m     09/01/2016   Page 4 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories DIN rail, unperforated - NS 32 UNPERF 2000MM - 1201015 G-profile DIN rail, material: Steel, unperforated, height 15 mm, width 32 mm, length 2 m     DIN rail perforated - NS 35/ 7,5 PERF 2000MM - 0801733 DIN rail, material: steel galvanized and passivated with a thick layer, perforated, height 7.5 mm, width 35 mm, length: 2000 mm     DIN rail, unperforated - NS 35/ 7,5 UNPERF 2000MM - 0801681 DIN rail, material: Steel, unperforated, height 7.5 mm, width 35 mm, length: 2 m     DIN rail perforated - NS 35/ 7,5 WH PERF 2000MM - 1204119 DIN rail 35 mm (NS 35)     DIN rail - NS 35/ 7,5 WH UNPERF 2000MM - 1204122 DIN rail 35 mm (NS 35)     09/01/2016   Page 5 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories DIN rail, unperforated - NS 35/ 7,5 AL UNPERF 2000MM - 0801704 DIN rail, unperforated, Width: 35 mm, Height: 7.5 mm, Length: 2000 mm, Color: silver     DIN rail perforated - NS 35/ 7,5 ZN PERF 2000MM - 1206421 DIN rail, material: Galvanized, perforated, height 7.5 mm, width 35 mm, length: 2 m     DIN rail, unperforated - NS 35/ 7,5 ZN UNPERF 2000MM - 1206434 DIN rail, material: Galvanized, unperforated, height 7.5 mm, width 35 mm, length: 2 m     DIN rail, unperforated - NS 35/ 7,5 CU UNPERF 2000MM - 0801762 DIN rail, material: Copper, unperforated, height 7.5 mm, width 35 mm, length: 2 m     End cap - NS 35/ 7,5 CAP - 1206560 DIN rail end piece, for DIN rail NS 35/7.5     09/01/2016   Page 6 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories DIN rail perforated - NS 35/15 PERF 2000MM - 1201730 DIN rail, material: steel galvanized and passivated with a thick layer, perforated, height 15 mm, width 35 mm, length: 2000 mm     DIN rail, unperforated - NS 35/15 UNPERF 2000MM - 1201714 DIN rail, material: Steel, unperforated, height 15 mm, width 35 mm, length: 2 m     DIN rail perforated - NS 35/15 WH PERF 2000MM - 0806602 DIN rail 35 mm (NS 35)     DIN rail - NS 35/15 WH UNPERF 2000MM - 1204135 DIN rail 35 mm (NS 35)     DIN rail, unperforated - NS 35/15 AL UNPERF 2000MM - 1201756 DIN rail, deep drawn, high profile, unperforated, 1.5 mm thick, material: aluminum, height 15 mm, width 35 mm, length 2000 mm     09/01/2016   Page 7 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories DIN rail perforated - NS 35/15 ZN PERF 2000MM - 1206599 DIN rail, material: Galvanized, perforated, height 15 mm, width 35 mm, length: 2 m     DIN rail, unperforated - NS 35/15 ZN UNPERF 2000MM - 1206586 DIN rail, material: Galvanized, unperforated, height 15 mm, width 35 mm, length: 2 m     DIN rail, unperforated - NS 35/15 CU UNPERF 2000MM - 1201895 DIN rail, material: Copper, unperforated, 1.5 mm thick, height 15 mm, width 35 mm, length: 2 m     End cap - NS 35/15 CAP - 1206573 DIN rail end piece, for DIN rail NS 35/15     DIN rail, unperforated - NS 35/15-2,3 UNPERF 2000MM - 1201798 DIN rail, material: Steel, unperforated, 2.3 mm thick, height 15 mm, width 35 mm, length: 2 m     End block 09/01/2016   Page 8 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories End clamp - CLIPFIX 35 - 3022218 Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, width: 9.5 mm, color: gray     End clamp - CLIPFIX 35-5 - 3022276 Quick mounting end clamp for NS 35/7,5 DIN rail or NS 35/15 DIN rail, with marking option, with parking option for FBS...5, FBS...6, KSS 5, KSS 6, width: 5.15 mm, color: gray     End clamp - E/NS 35 N - 0800886 End clamp, width: 9.5 mm, color: gray     End clamp - E/UK - 1201442 End clamp, Width: 9.5 mm, Height: 35.3 mm, Length: 50.5 mm, Color: gray     End clamp - E/UK 1 - 1201413 End clamps, for supporting the ends of double-level and three-level terminal blocks, width: 10 mm, color: gray     End cover 09/01/2016   Page 9 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories End cover - D-UDK 4 - 2775113 End cover, Length: 63.5 mm, Width: 1.5 mm, Color: gray     Insertion bridge Insertion bridge - EB 3- 6 - 0201142 Insertion bridge, Pitch: 6.2 mm, Number of positions: 3, Color: gray     Insertion bridge - EB 2- 6 - 0201155 Insertion bridge, Pitch: 6.2 mm, Number of positions: 2, Color: gray     Insertion bridge - EB 10- 6 - 0201139 Insertion bridge, Pitch: 6.2 mm, Number of positions: 10, Color: gray     Insulating sleeve Bridge bar isolator - IS-K 4 - 1302338 Bridge bar isolator, Color: gray     09/01/2016   Page 10 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories Labeled terminal marker Zack marker strip - ZB 6 CUS - 0824992 Zack marker strip, can be ordered: Strip, white, labeled according to customer specifications, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Zack marker strip - ZB 6,LGS:FORTL.ZAHLEN - 1051016 Zack marker strip, Strip, white, labeled, can be labeled with: Plotter, Printed horizontally: Consecutive numbers 1 - 10, 11 - 20, etc. up to 491 - 500, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Zack marker strip - ZB 6,QR:FORTL.ZAHLEN - 1051029 Zack marker strip, Strip, white, labeled, can be labeled with: Plotter, Printed vertically: Consecutive numbers 1 - 10, 11 - 20, etc. up to 491 - 500, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Zack marker strip - ZB 6,LGS:GLEICHE ZAHLEN - 1051032 Zack marker strip, Strip, white, labeled, can be labeled with: Plotter, Printed horizontally: Identical numbers 1 or 2, etc. up to 100, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Marker for terminal blocks - ZB 6,LGS:L1-N,PE - 1051414 Marker for terminal blocks, Strip, white, labeled, can be labeled with: Plotter, Horizontal: L1, L2, L3, N, PE, L1, L2, L3, N, PE, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     09/01/2016   Page 11 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories Marker for terminal blocks - ZB 6,LGS:U-N - 1051430 Marker for terminal blocks, Strip, white, labeled, can be labeled with: Plotter, Printed horizontally: U, V, W, N, GND, U, V, W, N, GND, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Marker for terminal blocks - UC-TM 6 CUS - 0824589 Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 5.6 x 10.5 mm     Marker for terminal blocks - UCT-TM 6 CUS - 0829602 Marker for terminal blocks, can be ordered: by sheet, white, labeled according to customer specifications, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 5.6 x 10.5 mm     Partition plate Separating plate - TS-KK 3 - 2770215 Separating plate, Length: 14 mm, Width: 0 mm, Height: 16 mm, Color: gray     Screw bridge Jumper - ISSBI 10- 6 - 0301505 Jumper, Pitch: 6 mm, Number of positions: 10, Color: silver     09/01/2016   Page 12 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories Fixed bridge - FBI 100- 6 - 0201650 Fixed bridge, Pitch: 6 mm, Number of positions: 100, Color: silver     Fixed bridge - FBI 10- 6 - 0203250 Fixed bridge, Pitch: 6 mm, Number of positions: 10, Color: silver     Fixed bridge - FBI 20- 6 - 0201867 Fixed bridge, Pitch: 6 mm, Number of positions: 20, Color: silver     Screwdriver tools Screwdriver - SZS 0,6X3,5 - 1205053 Actuation tool, for ST terminal blocks, insulated, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2-component grip, with non-slip grip     Terminal marking 09/01/2016   Page 13 / 14 https://www.phoenixcontact.com/us/products/3232011 Feed-through terminal block - UDK 4-DUR 249 P/P - 3232011 Accessories Marker card - SBS 6:UNBEDRUCKT - 1007222 Marker card, Card, white, unlabeled, can be labeled with: Plotter, Mounting type: Snap into tall marker groove, Snap into flat marker groove, for terminal block width: 6.2 mm, Lettering field: 6 x 6.1 mm     Zack marker strip - ZB 6:UNBEDRUCKT - 1051003 Zack marker strip, Strip, white, unlabeled, can be labeled with: Plotter, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 6.15 x 10.5 mm     Marker for terminal blocks - UC-TM 6 - 0818085 Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK CLED, BLUEMARK LED, Plotter, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 5.6 x 10.5 mm     Marker for terminal blocks - UCT-TM 6 - 0828736 Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: THERMOMARK CARD, BLUEMARK CLED, BLUEMARK LED, TOPMARK LASER, THERMOMARK PRIME, Mounting type: Snap into tall marker groove, for terminal block width: 6.2 mm, Lettering field: 5.6 x 10.5 mm     Phoenix Contact 2016 © - all rights reserved http://www.phoenixcontact.com 09/01/2016   Page 14 / 14