M17-17S1N8A8004

https://www.phoenixcontact.com/gb/products/1629047 Cable connector - M17-17S1N8A8004 - 1629047 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Cable connector, straight, shielded: yes, Screw locking, M17, No. of pos.: 17, type of contact: Socket, Crimp connection, cable diameter range: 8.5 mm ... 12 mm, coding:N Your advantages  Solutions with cross-manufacturer compatibility for standard and fast locking systems  Reliable under the harshest conditions: cable connectors with vibration brake  Modern, consistent design for highly convenient operation  Easy, cost-effective cable assembly: uniform shielding of M17 to M40 Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626706269 Weight per Piece (excluding packing) 22.220 g Custom tariff number 85366990 Sales Key ABRBGA Technical data Temperature range Ambient temperature -40 °C ... 105 °C (see derating curve) Standards and Regulations Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. 08/23/2021   Page 1 / 5 https://www.phoenixcontact.com/gb/products/1629047 Cable connector - M17-17S1N8A8004 - 1629047 Technical data Standards and Regulations The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. • The products are suitable for applications in plant, controller, and electrical device engineering. • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. • Assembled products may not be manipulated or improperly opened. • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). • When using the product in direct connection with third-party manufacturers, the user is responsible. • For operating voltages > 50 V AC, conductive connector housings must be grounded • Ensure that the protective or functional ground has been properly connected. • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector • Only use tools recommended by Phoenix Contact • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. • Operate the connector only when it is fully plugged in and interlocked. • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. • Observe the minimum bending radius of the cable. Lay the cable without twisting it. • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Data of the insulating body Coding N Contact connection method Crimp connection Type of contacts Socket Application Signal Number of positions 17 Contact diameter of power contacts 0.6 mm Rated current for power contacts 3.6 A Rated voltage 60 V Rated surge voltage 1.5 kV Overvoltage category III Degree of pollution 3 Rated surge voltage 60 V Overvoltage category II 08/23/2021   Page 2 / 5 https://www.phoenixcontact.com/gb/products/1629047 Cable connector - M17-17S1N8A8004 - 1629047 Technical data Data of the insulating body Degree of pollution 3 Installation height 3000 m Housing data Housing material GD-Zn Type of locking Screw locking Degree of protection (when plugged in) IP67 IP68, 24 h / 2 m Thread type M17 Cable seal data Cable diameter 8.5 mm ... 12 mm Environmental Product Compliance China RoHS Environmentally friendly use period: unlimited = EFUP-e No hazardous substances above threshold values Drawings 1 13 2 12 3 11 14 Diagram I [A] Schematic diagram 10 17 10 4 5 9 16 15 6 1 5 8 7 Connector pin assignment 1 0 0 2 = 17x0,5 mm 10 20 30 40 50 60 70 80 90 100 110  [°C] I = current strength, T = ambient temperature 08/23/2021   Page 3 / 5 https://www.phoenixcontact.com/gb/products/1629047 Cable connector - M17-17S1N8A8004 - 1629047 Dimensional drawing Ø22,5 Ø22,5 53,7 Dimensional drawing Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 11.0 27440102 eCl@ss 9.0 27440102 ETIM ETIM 6.0 EC002061 ETIM 7.0 EC002635 UNSPSC UNSPSC 18.0 39121413 UNSPSC 19.0 39121413 UNSPSC 20.0 39121413 UNSPSC 21.0 39121413 Accessories Accessories Crimp contact Crimp contact - ST-06KS010 - 1607580 Crimp contact, turned, contact diameter: 0.6 mm, crimp range: 0.06 mm² ... 0.25 mm²     08/23/2021   Page 4 / 5 https://www.phoenixcontact.com/gb/products/1629047 Cable connector - M17-17S1N8A8004 - 1629047 Accessories Crimp contact - ST-06KS020 - 1607581 Crimp contact, turned, contact diameter: 0.6 mm, crimp range: 0.14 mm² ... 0.34 mm²     Crimp contact - ST-06KS030 - 1607582 Crimp contact, turned, contact diameter: 0.6 mm, crimp range: 0.34 mm² ... 0.5 mm²     Protective cover Metal protective cap - ST-Z0077 - 1627217 Metal protection cap with steel wire and loop for M17 connectors with knurled nut for fastening to the cable     Phoenix Contact 2021 © - all rights reserved http://www.phoenixcontact.com 08/23/2021   Page 5 / 5