https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's
documentation. Our General Terms of Use for Downloads are valid
(http://phoenixcontact.com/download)
PLC-INTERFACE, consisting of DIN-rail-mountable basic terminal block in 6.2 mm with Push-in connection
and plug-in miniature relay with 6 A power contact, 1 changeover contact, 230 V AC/220 V DC input voltage.
Approved according to ATEX/IECEx (Zone 2) and Ex Zone Class I, Div. 2.
Key Commercial Data
Packing unit
10 pc
Minimum order quantity
10 pc
GTIN
GTIN
4055626363677
Weight per Piece (excluding packing)
38.930 g
Custom tariff number
85364900
Country of origin
Germany
Technical data
Note
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download
area
Dimensions
Width
6.2 mm
Height
80 mm
Depth
94 mm
Ambient conditions
Ambient temperature (operation)
-20 °C ... 60 °C (UL)
-40 °C ... 55 °C (ATEX / IECEx)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Coil side
Nominal input voltage UN
230 V AC
12/31/2018 Page 1 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Technical data
Coil side
220 V DC
Typical input current at UN
3.2 mA (UN = 230 V AC)
3 mA (UN = 220 V DC)
Typical response time
7 ms
Typical release time
15 ms
Protective circuit
Bridge rectifier Bridge rectifier
Operating voltage display
Yellow LED
Power dissipation for nominal condition
0.74 W
Contact side
Contact type
1 PDT
Type of switch contact
Single contact
Contact material
AgSnO
Maximum switching voltage
250 V AC/DC (The separating plate PLC-ATP should be installed for
voltages larger than 250 V (L1, L2, L3) between identical terminal blocks
in adjacent modules. Potential bridging is then carried out with FBST 8PLC... or ...FBST 500...)
Minimum switching voltage
5 V (at 100 mA)
Min. switching current
10 mA (at 12 V)
Maximum inrush current
10 A (4 s)
Limiting continuous current
6A
Interrupting rating (ohmic load) max.
140 W (at 24 V DC)
20 W (at 48 V DC)
18 W (at 60 V DC)
23 W (at 110 V DC)
40 W (at 220 V DC)
1500 VA (for 250 V AC)
Switching capacity
2 A (at 24 V, DC13)
0.2 A (at 110 V, DC13)
0.1 A (at 220 V, DC13)
3 A (at 24 V, AC15)
3 A (at 120 V, AC15)
3 A (at 230 V, AC15)
General
Test voltage relay winding/relay contact
4 kV AC (50 Hz, 1 min.)
Operating mode
100% operating factor
Degree of protection
IP20 (Relay base)
Mechanical service life
2x 10 cycles
ATEX
II 3G Ex ec nC IIC T4 Gc
EU-type examination certificate
IBExU16ATEXB015 X
IECEx
Ex ec nC IIC T4 Gc
7
12/31/2018 Page 2 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Technical data
General
IECEx certificate
IECEx IBE 16.0029X
UL, USA
Class I, Zone 2, AEx nA nC IIC T6
UL, USA/Canada
Class I, Div. 2, Groups A, B, C, D
UL, Canada
Class I, Zone 2, Ex nA nC IIC Gc T6 X
Mounting position
any
Assembly instructions
In rows with zero spacing
Connection data input side
Connection name
Coil side
Connection method
Push-in connection
Stripping length
8 mm
Conductor cross section solid
0.14 mm² ... 2.5 mm²
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
0.2 mm² ... 2.5 mm² ()
2x 0.5 mm² ... 1 mm² ()
Conductor cross section AWG
26 ... 14
Connection data output side
Connection name
Contact side
Connection method
Push-in connection
Stripping length
8 mm
Conductor cross section solid
0.14 mm² ... 2.5 mm²
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
0.2 mm² ... 2.5 mm² ()
2x 0.5 mm² ... 1 mm² ()
Conductor cross section AWG
26 ... 14
Standards and Regulations
Designation
Standards/regulations
Standards/regulations
IEC 60664
EN 50178
EN 60079-0, -7, -15
Degree of pollution
3
Overvoltage category
III
Flammability rating according to UL 94
V0
Conformance
CE-compliant
ATEX
II 3G Ex ec nC IIC T4 Gc
IECEx
Ex ec nC IIC T4 Gc
UL, USA
Class I, Zone 2, AEx nA nC IIC T6
UL, USA/Canada
Class I, Div. 2, Groups A, B, C, D
UL, Canada
Class I, Zone 2, Ex nA nC IIC Gc T6 X
Environmental Product Compliance
12/31/2018 Page 3 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Technical data
Environmental Product Compliance
REACh SVHC
Lead 7439-92-1
China RoHS
Environmentally Friendly Use Period = 50
For details about hazardous substances go to tab “Downloads”,
Category “Manufacturer's declaration”
Drawings
Diagram
Diagram
U
U N 1,4
1,3
1,2
A
1,1
UN= 220 V DC / 230 V AC
1
0,9
0,8
B
0,7
20
Interrupting rating
25
30
35
40
45
50
55
60
65
TU [ ° C]
Curve A
Maximum permissible continuous voltage Umax with limiting continuous
current on the contact side (see relevant technical data)
Curve B
Minimum permissible operate voltage Uop after pre-excitation (see
relevant technical data)
Circuit diagram
A2
11
A1
14
12
Classifications
eCl@ss
eCl@ss 5.0
27371601
eCl@ss 5.1
27371600
eCl@ss 6.0
27371600
eCl@ss 7.0
27371601
12/31/2018 Page 4 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Classifications
eCl@ss
eCl@ss 8.0
27371601
eCl@ss 9.0
27371601
ETIM
ETIM 2.0
EC001437
ETIM 3.0
EC001437
ETIM 4.0
EC001437
ETIM 5.0
EC001437
ETIM 6.0
EC001437
UNSPSC
UNSPSC 6.01
30211916
UNSPSC 7.0901
39121515
UNSPSC 11
39121515
UNSPSC 12.01
39121515
UNSPSC 13.2
39122334
Approvals
Approvals
Approvals
EAC
Ex Approvals
IECEx / ATEX / UL Listed / cUL Listed / cULus Listed
Approval details
EAC
RU CDE.A*30.B.01082
Accessories
Accessories
Bridge
12/31/2018 Page 5 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
Continuous plug-in bridge - FBST 500-PLC RD - 2966786
Continuous plug-in bridge, length: 500 mm, color: red
Continuous plug-in bridge - FBST 500-PLC BU - 2966692
Continuous plug-in bridge, length: 500 mm, color: blue
Continuous plug-in bridge - FBST 500-PLC GY - 2966838
Continuous plug-in bridge, length: 500 mm, color: gray
Single plug-in bridge - FBST 6-PLC RD - 2966236
Single plug-in bridge, length: 6 mm, number of positions: 2, color: red
Single plug-in bridge - FBST 6-PLC BU - 2966812
Single plug-in bridge, length: 6 mm, number of positions: 2, color: blue
12/31/2018 Page 6 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
Single plug-in bridge - FBST 6-PLC GY - 2966825
Single plug-in bridge, length: 6 mm, number of positions: 2, color: gray
Single plug-in bridge - FBST 8-PLC GY - 2967688
Single plug-in bridge, length: 8 mm, number of positions: 2, color: gray
Controller board
System connection - PLC-V8/FLK14/OUT - 2295554
V8 adapter for 8 x PLC-INTERFACE (6.2 mm); Controller: PLC system cabling of output cards; connection 1: Plug
connection (Can be snapped onto 8x PLC-INTERFACE terminals); connection 2: 1x IDC/FLK pin strip (14-position);
number of channels: 8; control logic: positive switching
System connection - PLC-V8/FLK14/OUT/M - 2304102
V8 adapter for 8 x PLC-INTERFACE (6.2 mm); Controller: PLC system cabling of output cards; connection 1: Plug
connection (Can be snapped onto 8x PLC-INTERFACE terminals); connection 2: 1x IDC/FLK pin strip (14-position);
number of channels: 8; control logic: negative switching
System connection - PLC-V8/D15S/OUT - 2296058
V8 adapter for 8 x PLC-INTERFACE (6.2 mm); Controller: PLC system cabling of output cards; connection 1: Plug
connection (Can be snapped onto 8x PLC-INTERFACE terminals); connection 2: 1x D-SUB pin strip (15-position);
number of channels: 8; control logic: positive switching
12/31/2018 Page 7 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
System connection - PLC-V8/D15B/OUT - 2296061
V8 adapter for 8 x PLC-INTERFACE (6.2 mm); Controller: PLC system cabling of output cards; connection 1: Plug
connection (Can be snapped onto 8x PLC-INTERFACE terminals); connection 2: 1x D-SUB socket strip (15-position);
number of channels: 8; control logic: positive switching
DIN rail
DIN rail, unperforated - NS 35/ 7,5 V2A UNPERF 2000MM - 0801377
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Stainless steel
V2A, uncoated, length: 2000 mm, color: silver
DIN rail perforated - NS 35/ 7,5 PERF 2000MM - 0801733
DIN rail perforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/ 7,5 CU UNPERF 2000MM - 0801762
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Copper, uncoated,
length: 2000 mm, color: copper-colored
DIN rail, unperforated - NS 35/15 UNPERF 2000MM - 1201714
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
12/31/2018 Page 8 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
DIN rail, unperforated - NS 35/15 CU UNPERF 2000MM - 1201895
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Copper,
uncoated, length: 2000 mm, color: copper-colored
DIN rail, unperforated - NS 35/15-2,3 UNPERF 2000MM - 1201798
DIN rail, unperforated, Standard profile 2.3 mm, width: 35 mm, height: 15 mm, acc. to EN 60715, material: Steel,
galvanized, passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/15 AL UNPERF 2000MM - 1201756
DIN rail, unperforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Aluminum,
uncoated, length: 2000 mm, color: silver
DIN rail perforated - NS 35/15 PERF 2000MM - 1201730
DIN rail perforated, Standard profile, width: 35 mm, height: 15 mm, similar to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
DIN rail, unperforated - NS 35/ 7,5 UNPERF 2000MM - 0801681
DIN rail, unperforated, Standard profile, width: 35 mm, height: 7.5 mm, acc. to EN 60715, material: Steel, galvanized,
passivated with a thick layer, length: 2000 mm, color: silver
Labeled terminal marker
12/31/2018 Page 9 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
Zack marker strip - ZB 6,LGS:FORTL.ZAHLEN - 1051016
Zack marker strip, Strip, white, labeled, can be labeled with: CMS-P1-PLOTTER, printed horizontally: consecutive
numbers 1 ... 10, 11 ... 20, etc. up to 491 ... 500, mounting type: snap into tall marker groove, for terminal block width:
6.2 mm, lettering field size: 6.15 x 10.5 mm
Partition plate
Separating plate - PLC-ATP BK - 2966841
Separating plate, 2 mm thick, required at the start and end of a PLC terminal strip. Furthermore, it is used for: visual
separation of groups, safe isolation of different voltages of neighboring PLC relays in acc. with DIN VDE 0106-101,
isolation
Power module
Power terminal block - PLC-ESK GY - 2966508
Power terminal block, for the input of up to four potentials, for mounting on NS 35/7.5
Screwdriver tools
Screwdriver - SZF 1-0,6X3,5 - 1204517
Actuation tool, for ST terminal blocks, also suitable for use as a bladed screwdriver, size: 0.6 x 3.5 x 100 mm, 2component grip, with non-slip grip
Terminal marking
Zack marker strip - ZB 6:UNBEDRUCKT - 1051003
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm
12/31/2018 Page 10 / 11
https://www.phoenixcontact.com/in/products/2909530
Relay Module - PLC-RPT-230UC/21/EX - 2909530
Accessories
Zack marker strip - ZB 6/WH-100:UNBEDRUCKT - 5060935
Zack marker strip, Strip, white, unlabeled, can be labeled with: PLOTMARK, CMS-P1-PLOTTER, mounting type:
snap into tall marker groove, for terminal block width: 6.2 mm, lettering field size: 6.15 x 10.5 mm
Marker for terminal blocks - UC-TM 6 - 0818085
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: BLUEMARK ID COLOR, BLUEMARK ID,
BLUEMARK CLED, PLOTMARK, CMS-P1-PLOTTER, mounting type: snap into tall marker groove, for terminal block
width: 6.2 mm, lettering field size: 5.6 x 10.5 mm
Marker for terminal blocks - UCT-TM 6 - 0828736
Marker for terminal blocks, Sheet, white, unlabeled, can be labeled with: TOPMARK NEO, TOPMARK LASER,
BLUEMARK ID COLOR, BLUEMARK ID, BLUEMARK CLED, THERMOMARK PRIME, THERMOMARK CARD 2.0,
THERMOMARK CARD, mounting type: snap into tall marker groove, for terminal block width: 6.2 mm, lettering field
size: 5.6 x 10.5 mm
Spare parts
Single relay - REL-MR- 60DC/21 - 2961118
Plug-in miniature power relay, with power contact, 1 PDT, input voltage 60 V DC
Phoenix Contact 2018 © - all rights reserved
http://www.phoenixcontact.com
12/31/2018 Page 11 / 11
