PLC-RSC- 12DC/21HC

https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) PLC-INTERFACE, consisting of PLC-BSC.../21 HC basic terminal block with screw connection and plug-in miniature relay for a high continuous current, for mounting on DIN rail NS 35/7,5, limiting continuous current up to 10 A, 1 PDT, input voltage 12 V DC The illustration shows the version PLC-RSC-230UC/21HC Product Features  All common input voltages of 12 V DC to 230 V AC  Efficient connection to system cabling using V8 adapter  Long electrical service life thanks to 16 A relay  Safe isolation according to DIN EN 50178 between coil and contact  Functional plug-in bridges  Max. continuous current of 10 A     Key Commercial Data Packing unit 1 pc Weight per Piece (excluding packing) 78.0 g Custom tariff number 85364900 Country of origin Germany Technical data Note Utilization restriction EMC: class A product, see manufacturer's declaration in the download area Dimensions Width 14 mm Height 80 mm Depth 94 mm 12/01/2015   Page 1 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Technical data Ambient conditions Ambient temperature (operation) -40 °C ... 60 °C Ambient temperature (storage/transport) -40 °C ... 85 °C Coil side Nominal input voltage UN 12 V DC Typical input current at UN 33 mA Typical response time 8 ms Typical release time 10 ms Protective circuit Protection against polarity reversal Polarity protection diode Free-wheeling diode Damping diode Operating voltage display Yellow LED Power dissipation for nominal condition 0.4 W Contact side Contact type 1 PDT Contact material AgNi Maximum switching voltage 250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...) Minimum switching voltage 12 V AC/DC Min. switching current 100 mA Maximum inrush current 30 A (300 ms) Limiting continuous current 10 A 6 A (value applies to connections 12. If connections 12 are bridged, the normal value applies.) Interrupting rating (ohmic load) max. 240 W (at 24 V DC) 58 W (at 48 V DC) 48 W (at 60 V DC) 50 W (at 110 V DC) 80 W (at 220 V DC) 2500 VA (for 250 V AC) Interrupting rating (ohmic load) max. bridged 144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.) 1500 VA (for 250 V AC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.) Switching capacity in acc. with DIN VDE 0660/IEC 60947 2 A (at 24 V, DC13) 0.2 A (at 110 V, DC13) 0.2 A (at 250 V, DC13) 6 A (at 24 V, AC15) 12/01/2015   Page 2 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Technical data Contact side 6 A (at 120 V, AC15) 6 A (at 250 V, AC15) Connection data input side Connection name Coil side Connection method Screw connection Stripping length 8 mm Screw thread M3 Conductor cross section solid 0.14 mm² ... 2.5 mm² Conductor cross section flexible 0.14 mm² ... 2.5 mm² AWG conductor cross section 26 ... 14 Connection data output side Connection name Contact side Connection method Screw connection Stripping length 8 mm Screw thread M3 Conductor cross section solid 0.14 mm² ... 2.5 mm² Conductor cross section flexible 0.14 mm² ... 2.5 mm² AWG conductor cross section 26 ... 14 General Test voltage relay winding/relay contact 4 kV AC (50 Hz, 1 min.) Operating mode 100% operating factor Degree of protection RT II (Relay) Mechanical service life 3 x 10 cycles Flammability rating according to UL 94 V0 Designation Standards/regulations Standards/regulations IEC 60664 7 EN 50178 IEC 62103 Rated surge voltage/insulation 6 kV / Safe isolation, increased insulation Pollution degree 2 Overvoltage category III Mounting position any Assembly instructions In rows with zero spacing Standards and Regulations Connection in acc. with standard CUL 12/01/2015   Page 3 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Technical data Standards and Regulations Designation Standards/regulations Standards/regulations IEC 60664 EN 50178 IEC 62103 Rated surge voltage/insulation 6 kV / Safe isolation, increased insulation Pollution degree 2 Overvoltage category III Flammability rating according to UL 94 V0 Classifications eCl@ss eCl@ss 4.0 27371102 eCl@ss 4.1 27371102 eCl@ss 5.0 27371001 eCl@ss 5.1 27371001 eCl@ss 6.0 27371001 eCl@ss 7.0 27371001 eCl@ss 8.0 27371601 eCl@ss 9.0 27371601 ETIM ETIM 2.0 EC000196 ETIM 3.0 EC000196 ETIM 4.0 EC000196 ETIM 5.0 EC001437 UNSPSC UNSPSC 6.01 30211916 UNSPSC 7.0901 39121515 UNSPSC 11 39121515 UNSPSC 12.01 39121515 UNSPSC 13.2 39121515 Approvals Approvals 12/01/2015   Page 4 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Approvals Approvals UL Recognized / UL Listed / cUL Recognized / cUL Listed / GL / EAC / RC FRT / EAC / cULus Recognized / cULus Listed Ex Approvals Approvals submitted Approval details UL Recognized  UL Listed  cUL Recognized  cUL Listed  GL  EAC  RC FRT  EAC  cULus Recognized  12/01/2015   Page 5 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Approvals cULus Listed  Drawings Diagram Circuit diagram Switching current [A] 20 10 6 4 1 11 2 3 1 2 A2 14 0,5 0,3 0,2 A1 12 0,1 10 20 30 50 70 100 200 Switching voltage [V] 300 1 AC, ohmic load 2 DC, ohmic load 3 DC, L/R = 40 ms Interrupting rating 12/01/2015   Page 6 / 7 https://www.phoenixcontact.com/us/products/2967617 Relay Module - PLC-RSC- 12DC/21HC - 2967617 Diagram Curve A Maximum permissible continuous voltage Umax with limiting continuous current on the contact side (see relevant technical data) Curve B Minimum permissible operate voltage Uop after pre-excitation (see relevant technical data) Phoenix Contact 2015 © - all rights reserved http://www.phoenixcontact.com 12/01/2015   Page 7 / 7