PSI-MOS-DNET CAN/FO 850/EM

https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) ® FO converter with integrated optical diagnosis, for DeviceNet™, CAN, CANopen to 800 kbps, extension/ redundancy module, interfaces: 1 x FO (BFOC), 850 nm, for HCS/fiberglass cable Product Features  Data rates of up to 800 kbps, set via DIP switches  Approved for use in zone 2  Intrinsically safe fiber optic interface (Ex op is) for direct connection to devices in zone 1  Integrated optical diagnostics for continuous monitoring of fiber optic paths  High-quality electrical isolation between all interfaces (DeviceNet // fiber optic port // power supply // backplane)  Integrated bus termination resistor can be connected internally  Integrated backplane for routing through the supply voltage and data signals  Connections can be plugged in using a COMBICON screw terminal block  Floating switch contact in the basic module for leading alarm generation in relation to critical fiber optic paths       Key commercial data Packing unit 1 pc Weight per Piece (excluding packing) 166.0 GRM Custom tariff number 85176200 Country of origin Germany Technical data Note Utilization restriction EMC: class A product, see manufacturer's declaration in the download area Dimensions Width 22.5 mm 10/10/2014   Page 1 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Technical data Dimensions Height 99 mm Depth 114.5 mm Ambient conditions Ambient temperature (operation) -20 °C ... 60 °C Ambient temperature (storage/transport) -40 °C ... 85 °C Permissible humidity (operation) 30 % ... 95 % (non-condensing) Altitude 5000 m (For restrictions see manufacturer's declaration) Degree of protection IP20 Noise immunity EN 61000-6-2:2005 Serial interface Interface 1 CAN interface, in accordance with ISO/IS 11898 for DeviceNet, CAN, CANopen Connection method Pluggable screw connection File format/coding Bit stuffing, NRZ Transmission medium Copper Transmission length ≤ 5000 m (Dependent on the data rate and the protocol used) Serial transmission speed ≤ 800 kbps Optical interface FO Transmit capacity, minimum -17.9 dBm (50/125 µm) -14.1 dBm (62,5/125 µm) -5.1 dBm (200/230 µm) Minimum receiver sensitivity -32.5 dBm (50/125 µm) -32.5 dBm (62,5/125 µm) -32.1 dBm (200/230 µm) Wavelength 850 nm Transmission length incl. 3 dB system reserve 2800 m (With F-K 200/230 10 dB/km with quick mounting connector) 4800 m (with F-G 50/125 2.5 dB/km) 4200 m (with F-G 62,5/125 3.0 dB/km) Transmission medium HCS fiber Multi-mode fiberglass Connection method ® B-FOC (ST ) Digital outputs Output name Relay output Output description Alarm output Number of outputs 1 Maximum switching voltage 60 V DC 10/10/2014   Page 2 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Technical data Digital outputs 42 V AC Limiting continuous current 0.46 A Power supply Supply voltage range 10 V DC ... 30 V DC Max. current consumption 100 mA Typical current consumption 100 mA (24 V DC) Connection method Pluggable COMBICON screw terminal block through basic module General Bit distortion, input ± 35 % (permitted) Bit distortion, output < 6.25 % Electrical isolation VCC // CAN Test voltage data interface/power supply 1.5 kVrms (50 Hz, 1 min.) Electromagnetic compatibility Conformance with EMC Directive 2004/108/EC Noise emission EN 55011 Housing material PA 6.6-FR Color green MTBF 323 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day)) 49 Years (Telcordia standard, 40°C temperature, 34.25% operating cycle (5 days a week, 12 hours a day)) Conformance CE-compliant ATEX  II 3 G Ex nAC IIC T4 X (Please follow the special installation instructions in the documentation!)  II (2) GD [Ex op is] IIC (PTB 06 ATEX 2042 U) (Please follow the special installation instructions in the documentation!) UL, USA / Canada Class I, Zone 2, AEx nc IIC T5 Class I, Div. 2, Groups A, B, C, D Classifications eCl@ss eCl@ss 4.0 27230207 eCl@ss 4.1 27230207 eCl@ss 5.0 27230207 eCl@ss 5.1 27230207 eCl@ss 6.0 27230207 eCl@ss 7.0 27230207 eCl@ss 8.0 27143136 10/10/2014   Page 3 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Classifications ETIM ETIM 2.0 EC001423 ETIM 3.0 EC001423 ETIM 4.0 EC001423 ETIM 5.0 EC001423 UNSPSC UNSPSC 6.01 30211506 UNSPSC 7.0901 39121008 UNSPSC 11 39121008 UNSPSC 12.01 39121008 UNSPSC 13.2 43201553 Approvals Approvals Approvals UL Recognized / cUL Recognized / cULus Recognized Ex Approvals ATEX / UL Listed Approvals submitted Approval details UL Recognized  cUL Recognized  10/10/2014   Page 4 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Approvals cULus Recognized  Accessories Accessories Adapter Fiber optic coupling - PSM-SET-BFOC-LINK/2 - 2799429 Coupling; set consisting of 2 couplings for connecting B-FOC plugs     Assembly tool Assembly tool - PSM-HCS-KONFTOOL/B-FOC - 2708465 HCS assembly kit for B-FOC (ST) quick mounting connectors, including stripping blade, stripping pliers, aramide yarn scissors, fiber stripper, microscope, fiber cleaving tool for standard HCS and HCS GI fibers, and documentation     Connector set FO connectors - PSM-SET-B-FOC/4-HCS - 2708481 B-FOC (ST) connector set for HCS fiber, for self assembly consisting of 4 quick mounting connectors with bend protection sleeve     Data cable by the meter 10/10/2014   Page 5 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Accessories FO cable - PSM-LWL-HCS-RUGGED-200/230 - 2799885 HCS cable, duplex 200/230 µm, by the meter, without connector, for indoor installation     FO cable - PSM-LWL-HCSO-200/230 - 2799445 HCS cable, duplex 200/230 µm, by the meter, without connector, for outdoor installation     FO cable - PSM-LWL-GDM-RUGGED- 50/125 - 2799322 Fiberglass cable, duplex 50/125 µm, by the meter, without connector, for indoor installation     FO cable - PSM-LWL-GDO- 50/125 - 2799432 Fiberglass cable, duplex 50/125 µm, by the meter, without connector, for outdoor installation     Bus system cable - SAC-5P-920/... - 1511504 ® Cable ring for CANopen and DeviceNet™ cable, 5-pos., in cable lengths from 0.5 m to 400 m     Data plug 10/10/2014   Page 6 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Accessories D-SUB bus connector - SUBCON-PLUS-CAN - 2744694 D-SUB connector, 9-pos. female connector, two cable entries < 35° to one terminal block row, bus system: CAN, ® CANopen , SafetyBUS p up to 1 Mbps, termination resistor can be switched on via slide switch, pin assignment: 2, 3, 7; screw connection terminal blocks     D-SUB bus connector - SUBCON-PLUS-CAN/PG - 2708119 ® D-SUB connector, 9-pos. socket, cable entry < 35°, bus system: CAN, CANopen , SafetyBUS p up to 1 Mbps, with PG D-SUB socket for connecting a programming device, termination resistor can be switched on via slide switch, pin assignment: 2, 3, 6, 7, 9; screw terminal blocks     D-SUB bus connector - SUBCON-PLUS-CAN/AX - 2306566 D-SUB connector, 9-pos. female connector, axial version with two cable entries, bus system: CAN, CANopen, SafetyBUS p; pin assignment: 2, 3, 7; screw connection terminal blocks     D-SUB bus connector - SUBCON-PLUS-CAN/90/PG/M12 - 2902322 D-SUB plug, 9-pos., socket, with PG-D-SUB pin, assignment: 2, 3, 5, 6, 7, 9; two M12 cable glands (A-coded) under 90°. Bus system: CAN, CANopen®. Termination resistor via separate M12 terminator.     D-SUB bus connector - SUBCON-PLUS-CAN/90/M12 - 2902323 D-SUB plug, 9-pos., socket, assignment: 2, 3, 5, 6, 7, 9; two M12 cable glands (A-coded) under 90°. Bus system: CAN, CANopen®. Termination resistor via separate M12 terminator.     10/10/2014   Page 7 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Accessories D-SUB bus connector - SUBCON-PLUS-CAN/35/PG/M12 - 2902324 D-SUB plug, 9-pos., socket, with PG-D-SUB pin, assignment: 2, 3, 5, 6, 7, 9; two M12 cable glands (A-coded) under 35°. Bus system: CAN, CANopen®. Termination resistor via separate M12 terminator.     D-SUB bus connector - SUBCON-PLUS-CAN/35/M12 - 2902325 D-SUB plug, 9-pos., socket, assignment: 2, 3, 5, 6, 7, 9; two M12 cable glands (A-coded) under 35°. Bus system: CAN, CANopen®. Termination resistor via separate M12 terminator.     D-SUB bus connector - SUBCON-PLUS-CAN/AX/M12 - 2902326 D-SUB plug, 9-pos., socket, assignment: 2, 3, 5, 6, 7, 9; two M12 cable glands (A-coded) under 180° (axial). Bus system: CAN, CANopen®. Termination resistor via separate M12 terminator.     D-SUB bus connector - SUBCON-PLUS-CAN - 2744694 D-SUB connector, 9-pos. female connector, two cable entries < 35° to one terminal block row, bus system: CAN, ® CANopen , SafetyBUS p up to 1 Mbps, termination resistor can be switched on via slide switch, pin assignment: 2, 3, 7; screw connection terminal blocks     D-SUB bus connector - SUBCON-PLUS-CAN/PG - 2708119 ® D-SUB connector, 9-pos. socket, cable entry < 35°, bus system: CAN, CANopen , SafetyBUS p up to 1 Mbps, with PG D-SUB socket for connecting a programming device, termination resistor can be switched on via slide switch, pin assignment: 2, 3, 6, 7, 9; screw terminal blocks     10/10/2014   Page 8 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Accessories D-SUB bus connector - SUBCON-PLUS-CAN/AX - 2306566 D-SUB connector, 9-pos. female connector, axial version with two cable entries, bus system: CAN, CANopen, SafetyBUS p; pin assignment: 2, 3, 7; screw connection terminal blocks     Measuring tools Measuring instrument - PSM-FO-POWERMETER - 2799539 Fiber optic measuring case, consisting of an optical power meter, F-SMA, B-FOC adapters, reference fibers and operating instructions     Screwdriver tools Screwdriver - SZS 0,4X2,5 VDE - 1205037 Screwdriver, slot-headed, VDE insulated, size: 0.4 x 2.5 x 80 mm, 2-component grip, with non-slip grip     Drawings Application drawing Application drawing FO FO BE B B BE B FO B Branch line / redundant branch line BE ...64x ...64x ...64x Linear structure 10/10/2014   Page 9 / 10 https://www.phoenixcontact.com/us/products/2708096 FO converters - PSI-MOS-DNET CAN/FO 850/EM - 2708096 Application drawing BE E E BE BE ...20 Application drawing BE E BE ...20 FO FO BE E BE E BE E FO B B B B BE BE BE B Star structure / redundant star structure B B B B B Tree structure Block diagram *) Only in the basic module Phoenix Contact 2014 © - all rights reserved http://www.phoenixcontact.com 10/10/2014   Page 10 / 10