VS-25-DEVNET

VARIOSUB D-SUB Fieldbus Plug Connectors co s. nt on l in ec om po ne Variosub-Bus are plug connectors in an IP 67 (dust and watertight) housing, with standard D-SUB inserts. Versions are available with specially adapted characteristics for the most common buses, namely Interbus, Profibus, CANopen and DeviceNet. Line structures can easily be configured using VARIOSUB plug connectors, as these are fitted with two cable entries. The plug connectors can be connected fast and conveniently in field conditions by means of the internal screw connection terminal blocks. The EMC inner sleeve provides optimum EMC protection. Special protection and terminating devices in accordance with the guidelines of the applicable fieldbus organization guarantee problem-free operation in the system. m Short Description Phoenix Contact GmbH & Co. KG • 32823 Blomberg, Germany Phone +49 52 35 3-00 • Fax +49 52 35 3-4 12 00 • www.phoenixcontact.com Fieldbus plug connectors for Interbus, Profibus and CanOpen Series Type Order No. Pcs./Pkt. VARIOSUB D-SUB 9 INTERBUS Male Female VS-09-IBS-ST VS-09-IBS-BU 16 89 27 1 16 89 28 4 1 VARIOSUB D-SUB 9 PROFIBUS Male VS-09-PROFIB 16 89 29 7 1 Female VS-09-CAN 16 89 30 7 ne [A] [V] [mm] om po [mm2] / AWG [mm2] / AWG [°C] in ec The plug connector comprises the sleeve, two cap nuts with seal for cable INTERBUS diameters of 5-9 mm, a cover cap, a marker, a coding profile set, the contact insert with screw terminal block, and the EMC inner sleeve. Guideline: INTERBUS guideline, conformity test. on l nt Insulation material Inflammability class in acc. with UL 94 Max.amperage Max. voltage Insertion/withdrawal cycles Degree of protection Cable diameter Connection cross section INTERBUS, CAN-BUS; rigid / flexible PROFIBUS; rigid / flexible Temperature range s. Technical data INTERBUS: 1 co VARIOSUB D-SUB 9 CAN-BUS m Description PA V0 1 63 ≥ 200 IP 67 5 to 9 0.14 - 0.50 / 26 - 20 0.14 - 1.50 / 26 - 16 - 20 to +70 CAN-BUS: The plug connector comprises the sleeve, two cap nuts with seal for cable diameters of 5-9 mm, a cover cap, a marker, a coding profile set, the contact insert with screw terminal block, and the EMC inner sleeve. The contact insert contains the terminating circuitry that can be connected using a switch accessible from the outside. At the same time the outgoing bus segment is switched off. This makes it easy to start up segment by segment and to perform trouble-shooting. Guideline: CANopen DR-303-1 (1999). ± 2 7 0 8 9 The plug connector comprises the sleeve, two cap nuts with seal for cable diameters of 5-9 mm, a cover cap, a marker, a coding profile set, the contact insert with screw terminal block, and the EMC inner sleeve. The contact insert contains the protective and terminating circuitry. The terminating circuitry can be connected using a switch accessible from the outside. At the same time the outgoing bus segment is switched off. This makes it easy to start up segment by segment and to perform trouble-shooting. Guideline: PNO 2.141 (2000). 8 3 ,5 PROFIBUS: 4 5 ,6 6 0 Dimensional drawing of housing Phoenix Contact page 2 of 3 2 4 Fieldbus plug connectors for DeviceNet Series Type Order No. Pcs./Pkt. VARIOSUB D-SUB 25, plug, for DeviceNet VS-25-DEVNET 16 52 24 0 1 VARIOSUB D-SUB 25, panel mounting frame, for DeviceNet VS-25-A-DEVNET S 16 52 25 3 1 co m Description PA V0 8 63 ≥ 1000 IP 67 5 to 13 0.75 - 1.50 / 18 - 16 - 20 to +70 nt [A] [V] po ne [mm] [mm2] / AWG [°C] 16,8 13,2 62 om www.phoenixcontact.com ø3 on l 46,5 66,4 TNR: 5126141-01 92 83,5 102 Dimensional drawing VS-25-A-DEVNET S 67,5 81 Dimensional drawing VS-25-DEVNET Phoenix Contact page 3 of 3 24  Phoenix Contact 06.03.03 24 in ec ø 3,4 18 The ODVA user organization responsible for DeviceNet provides special Combicon plug connectors. The VS-25-DEVNET integrates these Combicon contact inserts, whereby pin compatibility with standard contact inserts is guaranteed. The screw connection in the sleeve housing is suitable for both "Thick" and "Thin" cables. Two cables can comfortably be connected in one plug connector. A terminating resistor accessible from the outside facilitates startup and trouble-shooting. Control cabinet feed-throughs, device connections and distributors can be conveniently generated using the VS-25-DEVNET. The plug connector VS-25-DEVNET comprises the sleeve, two cap nuts with seal for cable diameters of 5-13 mm, a cover cap, a marker, a coding profile insert and the contact insert with screw terminal blocks. The contact insert includes the terminating resistor. The terminating resistor can be connected using a switch accessible from the outside. At the same, the outgoing bus segment is switched off. This makes it easy to start up segment by segment and to perform trouble-shooting. Guideline: DeviceNet Connector Profiles 75,5 17,6 DeviceNet 19,6 Insulation material Inflammability class in acc. with UL 94 Max.amperage Max. voltage Insertion/withdrawal cycles Degree of protection Cable diameter Connection cross section Temperature range s. Technical data