PAW3502DL-TD

PAW3502 PAW3502 USB OPTICAL MOUSE SINGLE CHIP General Description The PAW3502 is a CMOS process optical mouse sensor single chip with USB interface that serves as a nonmechanical motion estimation engine for implementing a computer mouse. Features USB interface Single power supply Optical motion estimation technology Complete 2-D motion sensor Accurate motion estimation over a wide range of surfaces High speed motion detection up to 28 inches/sec Power saving movement mode during times of no Speed 28 inches/sec 20g 400/800/1000/1200 CPI 3000 frames/sec 10mA @Mouse moving (Normal) 5mA @Mouse not moving (Sleep) 480uA @USB suspend (Suspend) Key Specification Power Supply Interface Optical Lens System Clock Wide operating supply range 4.25V ~ 5.5V USB 1:1 24.000 MHz Acceleration Supports three buttons (R, M, L) and three axes (X, Y, Z) output Resolution Z-axis support mechanical input (Z/2) Frame Rate USB spec. Complete Universal Serial Bus specs V1.1 Operating Current compatibility Complete USB HID specs V1.1 compatibility Package Integrated USB transceiver and 1.5Mbps USB serial interface engine Shrunk DIP14 Ordering Information Part Number PAW3502DL PAW3502DL-TD PAW3502DL-TK CPI 800 400 1200 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 1 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 1. Pin Configuration 1.1 Pin Description Pin # Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OSCIN BL LED VDDQ VSS VDD5V VDDA D+ DBR BM Z2 Z1 OSCOUT Type IN IN OUT Definition Oscillator input, connected to resonator or resistor Button left key input, normal pull-high (50k), press connect to low LED control BYPASS I/O voltage reference GND PWR Chip ground Chip power VDD, 5.0V BYPASS Analog voltage reference I/O I/O IN IN IN IN OUT USB D+ USB DButton right key input, normal pull-high (50k), press connect to low Button middle key input, normal pull-high (50k), press connect to low Z axis, support mechanical scroller input Z axis, support mechanical scroller input Oscillator output, connected to resonator 1.2 Pin Assignment LB 1 2 3 4 5 6 7 14 13 12 11 10 9 8 RB 1 +Y 7 14 8 +X Figure 1. Top View Pinout Figure 2. Top View of Mouse All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 2 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 2. Block Diagram and Operation POWER ON RESET VOLTAGE REGULATOR AND POWER CONTROL VDD5V VSS CMOS IMAGE SENSOR WHEEL Z1 Z2 Z-AXIS COUNTER DIGITAL SIGNAL PROCESSOR 5V PO W ER LED LED DRIVER VDDA VDDQ VOLTAGE REFERENCE BL BUTTON BM BR USB INTERFACE D+ DDEBUNCE OSCIN OSCILLATOR USB MOUSE CONTROLLER OSCOUT 24 MHZ RESONATOR Figure 3. Block Diagram The PAW3502 supports X, Y, Z three axes, and L, R, M three buttons under USB mode. It is a CMOS process optical mouse sensor single chip with USB interface that serves as a non-mechanical motion estimation engine for implementing a computer mouse. The PAW3502 is in a 14-pin optical package and comes with the resolution of 400/800/1000/1200 counts per inch (CPI) and the rate of motion up to 28 inches per second. It includes USB interface so that no mouse controller is needed to interface through USB. The PAW3502 can receive command and echo status or data format, both complete Universal Serial Bus® spec V1.1 and USB HID spec V1.1 compatibility. It is also a cost effective solution to support USB Mouse. All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 3 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 3. Specifications 3.1 Absolute Maximum Ratings Exposure to absolute maximum rating may affect device reliability. Symbol Parameter TSTG TA Storage Temperature Operating Temperature Lead Solder Temp ESD VDC VIN DC Supply Voltage DC Input Voltage -0.5 -0.5 Min. -40 -15 Max. 85 55 260 2 5.5 5.5 Unit °C °C °C kV V V All I/O pin For 10 seconds, 1.6 mm below seating plane. All pins, human body model MIL 883 Method 3015 Notes 3.2 Recommend Operating Condition Symbol Parameter TA VDD VN Z R A FCLK FR Operating Temperature Power Supply Voltage Supply Noise Distance from Lens Reference Plane to Surface Resolution Acceleration Clock Frequency Frame Rate 24 3000 2.3 400 2.4 Min. 0 4.25 5.0 Typ. Max. 40 5.5 100 2.5 1200 20 Unit °C V mV mm CPI g MHz frames/sec 28 inches/sec @400CPI 20 inches/sec @800CPI inches/sec 16 inches/sec @1000CPI 13 inches/sec @1200CPI Peak to peak within 0 - 80 MHz Refer to Figure 4. Notes S Speed 0 28 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 4 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 4. Z and 2D Assembly P ackage Lid Lens Z O BJE CT SUR FACE Figure 4. Distance from Lens Reference Plane to Surface +X +Y ESD LENS RING BASE PLATE PLASTIC SPRING CLIP LED SURFACE IS 0 REF. PCB SENSOR BASE PLATE ALIGNMENT POST Unit: mm Figure 5. 2D Assembly All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 5 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 5. USB Interface 5.1 USB Command Set Description (USB Descriptor) The USB HOST detects USB mouse device plug-in and assigns a new unique address to the USB mouse device, then asking USB mouse device for information about the device description, configuration description, and assigning a configuration value for USB mouse device during enumeration period. After enumeration, the USB mouse device is able to transfer motion and button value to the USB host. Descriptor Type Device Descriptor (18 bytes) Configuration Descriptor (9 bytes) Interface Descriptor (9 bytes) Human Interface Device Descriptor (9 bytes) Endpoint Descriptor (7 bytes) Byte 12 3A 00 09 32 09 00 09 00 07 05 19 95 75 A1 25 C0 08 Byte 01 09 01 02 04 21 05 01 01 03 05 00 7F 09 95 Byte 10 10 22 00 10 81 09 29 75 81 09 75 38 01 Byte 01 25 00 00 01 03 02 03 01 03 30 08 15 81 Byte 00 00 01 01 00 04 A1 15 81 05 09 95 81 06 Byte 00 01 01 03 01 00 01 00 02 01 31 02 25 C0 Byte 00 01 04 01 22 0A 05 25 95 09 15 81 7F Byte 08 02 A0 02 3E Human Interface Device Report Descriptor (62 bytes, 3D3B) 09 01 01 01 81 06 75 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 6 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 5.2 USB Data Report Format The USB report has two data formats, depending on boot or report protocol is selected. One kind of data format is the boot protocol used in legacy environment as 5.2.1. The other kind of data format is USB report protocol format which includes Z-wheel movement data in the fourth byte as 5.2.2. The Z-wheel is moved forward the fourth byte data is 01H, the Z-wheel is moved backward the fourth byte data is FFH, and the Z-wheel is idle the fourth byte data is 00H. 5.2.1 USB Boot Protocol for Legacy Operation Byte 1 Bit 0 1 2 3~7 0-7 0-7 Description 1 = Left button pressed 1 = Right button pressed 1 = Middle button pressed Reserved X data (D0 - D7). A positive value indicates motion to the right; a negative value X0 ~ X7 indicates motion to the left. Bit 0 = LSB. Y data (D0 - D7). A positive value indicates device motion upward; a negative Y0 ~ Y7 value indicates motion downward. Bit 0 = LSB. Symbol BL BR BM NC 2 3 5.2.2 USB Report Protocol Byte Bit 0 1 2 3 4 5~7 0-7 0-7 0-7 Description 1 = Left button pressed 1 = Right button pressed 1 = Middle button pressed Reserved Reserved Reserved X data (D0 - D7). A positive value indicates motion to the right; a negative value X0 ~ X7 indicates motion to the left. Bit 0 = LSB. Y data (D0 - D7). A positive value indicates device motion upward; a negative Y0 ~ Y7 value indicates motion downward. Bit 0 = LSB. Z-wheel motion data (D0 - D7). A positive value indicates device motion Z0 ~ Z7 downward; a negative value indicates motion upward. The Z0 - Z7 limit value is ±7. Bit 0 = LSB. Symbol BL BR BM B4 B5 NC 1 2 3 4 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 7 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 6. Referencing Application Circuit Y1 24Mhz U1 *R3 1 OSC I N BL LED VDDQ VSS VDD5V VDDA OSC OU T Z1 Z2 BM BR DD+ 14 13 12 11 10 9 8 ENSW1 Z1 COM Z2 VDD_5V R1 BL D1 LED *R2 C4 VDD_5V 2 3 VDD_5V C5 + 4 BM C2 1uF 5 BR R4 33 R5 33 0.1uF 10uF JP1 1 2 3 4 5 + 6 7 C1 + C3 C6 C7 27pF PAW3502 1uF 0.1uF 27pF USB CABLE Note: *R2 and *R3 are reserved for future use. Figure 6. Application Circuit for PAW3502 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 8 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 7. Package Information 7.1 Package Outline Drawing 14 13 12 11 10 9 8 1 2 3 4 5 6 7 13.208 0.520 3.20 0.126 1.42 0.056 10.16 0.400 1.02 0.040 5.08 0.200 0.254 0.010 0.457 0.018 1.778 0.070 Max. 12 14.22 +/- 0.2 0.560 +/-0.0079 4.064 0.160 4 5 6 7 7.874 0.310 6.604 0.260 1 2 3 5.334 0.210 5.080 0.200 NOTES: 1. All dimensions in MM/INCH. 2. All dimensions tolerance: +/- 0.10mm 3. Maxmumflash: +0.2mm 4.55 0.179 14 13 12 11 10 9 8 5.6 0.220 0.80 0.031 Figure 7. Package Outline Drawing All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 9 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw PixArt Imaging Inc. PAW3502 USB Optical Mouse Sensor Single Chip 7.2 Recommended PCB Mechanical Cutouts and Spacing 4.046 0.160 1 2 3 4 5 6 7 7.544 0.297 16.942 0.667 12.877 0.507 9.068 0.357 1.778 0.070 6.985 0.275 8.89 0.350 10.221 0.402 0.711 0.028 1.19 0.047 14 13 12 11 10 9 8 27.94 1.100 3.251 0.128 0.711 0.028 All Dimension : mm/inch Back Side Figure 8. Recommended PCB Mechanical Cutouts and Spacing 8. Update History Version V0.1 V0.2 Update Creation, Preliminary 1st version Modify Referencing Application Circuit Date 10/11/2006 12/28/2006 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. 10 V0.2 Dec. 2006 PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw