HBS066ZE-A

HBS SERIES - 75 WATT DESCRIPTION FEATURES • • • • Water Washable “True-Trim” Option 1500V Isolation Positive Or Negative Logic HBS single output DC/DC converters provide up to • Industry Standard HalfBrick 75 watts of output power in an industry standard • Open-Frame Packaging half-brick package and footprint. These units feature excellent efficiency, Class A conducted noise specs, and • 100°C Baseplate Operation fixed switching frequency. The HBS features open-frame packaging, along with planar magnetics to provide maximum useable power with minimal thermal constraints. The HBS converters are especially suited to telecom, networking, and industrial applications, and are fully compatible with production board washing processes. TECHNICAL SPECIFICATIONS Input Voltage Range 24 VDC Nominal 48 VDC Nominal Reflected Ripple Input Reverse Voltage Protection 18 - 36 VDC 34 - 75 VDC 20% Iin Max. Shunt Diode Output Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit / Overcurrent Protection Current Limit Threshold Range, % of Iout Rated OVP Trip Range OVP ±1% 0.2% Vout 0.2% Vout 0.5 VDC 10 % Iout Rated 25% Iout 4% Vout 500 µs ±10% Hiccup 110 - 140% 115 - 140% Vout Nom. Hiccup Efficiency vs. Load (48V Input) 90 85 80 75 70 65 HBS075ZG-ANT HBS050ZE-ANT 60 55 50 10 20 30 40 50 60 70 80 90 100 LOAD % General Turn-On Time Remote Shutdown Remote Shutdown Reference Switching Frequency Isolation, Input - Output Isolation, Input - Case Isolation, Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (approx.) REV. 09/01 10 ms Positive Or Negative Logic Vin Negative 500 kHz 1500 VDC 1050 VDC 500 VDC 0.002%/°C -40 To +100°C -40 To +125°C 105 To 115°C 5 g, 10 - 55 Hz 2.1 x 106 hrs UL, cUL, VDE 2.5 oz Notes † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. 1 HBS SERIES - 75 WATT MODELS - (See the last page of section for options.) MODEL INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) RIPPLE & NOISE pk-pk (mV) TYPICAL EFFICIENCY** HBS066YE-A ∆ 24 18-36 HBS075YG-A 24 18-36 HBS075YH-A 24 18-36 HBS075YJ-A ∆ 24 18-36 HBS066ZE-A 48 34-75 HBS075ZG-A 48 34-75 HBS075ZH-A 48 34-75 HBS075ZJ-A 48 34-75 HBS075ZE-A 48 34-75 NOTES: ∆ Advanced product release - consult factory. 4.6 5.4 5.4 5.4 2.5 2.7 2.7 2.7 2.8 3.3 5 12 15 3.3 5 12 15 3.3 20 15 6.25 5 20 15 6.25 5 22.7 100 100 150 150 100 100 150 150 100 80% 83% 85% 86% 80% 84% 86% 87% 80% * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 2.28" (57.9mm) MOUNTING INSERTS M3X.5 THROUGH 4PL 5 6 1.400"(35.6mm) 1.000"(25.4mm) 0.700"(17.8mm) 0.400"(10.2mm) 0 -0.50"(-12.7mm) DIA 0.040" (1.0mm) 7PL DIA 0.080" (2.0mm) 2PL 0.18" (4.6mm) 1 2 2.40" (61.0mm) 3 4 BOTTOM VIEW 8 9 1.900" (48.3mm) 0 -0.19" (-4.8mm) 0.025" REF. (0.6mm) Pin Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 6.6 °C/W 5.7 °C/W 4.2 °C/W 3.1 °C/W 2.6 °C/W 1 2 3 4 5 6 7 8 9 Function Tolerances -Vin Case On/Off +Vin -Vout -Sense Trim +Sense +Vout Inches: .XX ± 0.020 .XXX ± 0.010 Pin: ± 0.002 (Millimeters) .X ± 0.5 .XX ± 0.25 HBS 0.50" (12.7mm) 7 ± 0.05 Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. (Dimensions as listed unless otherwise specified.) 2 OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. Negative Logic OPTION SUFFIX N T Lucent-Compatible Trim Terminal Strip Trim Enable Trim and Enable Current Share Headerless PIN LENGTH AND HEATSINK OPTIONS TS 1 2 3 4 Y 8 9 1H 1V 2H 2V 3H 3V HAS, HBD, HBS, HES, HLS, LES, QBS, QES, QLS, TES, TQD HAS, HBD, HBS, HES, HLS, QBS, QES, QLS XWS, XWD, XWT IAS, LES IAD, IAS, LES, SMS IAS, LES SMS Encapsulated EWS, IWS, OWS All Units (Except SMS) All Units (Except SMS) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) All Units (Except DIP, HLS, HLD, QLS, SIP, SM, TLD, and TKD Packages) APPLICABLE SERIES TTL “Low” Turns Module ON TTL “High” Turns Module OFF REMARKS 0.110” (2.8mm) Pin Length 0.150” (3.8mm) Pin Length 0.24” (6.1mm) Horizontal Heatsink 0.24” (6.1mm) Vertical Heatsink 0.45” (11.4mm) Horizontal Heatsink 0.45” (11.4mm) Vertical Heatsink 0.95” (24.1mm) Horizontal Heatsink 0.95” (24.1mm) Vertical Heatsink Standard Pin Length is 0.180” (4.6mm) Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Example Options: HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent-compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3