IAD010ZGG

(888) IPD-CONVerters q (888) 473-2668 q www.ipdconverters.com IAD SERIES - DUAL OUTPUT, 12 WATT DESCRIPTION IAD dual output DC/DC converters provide up to 12 Watts of output power in an industry standard package and footprint. With a maximum case temperature of 100°C, the IAD is well suited for the most demanding applications. The IAD features 1500 VDC isolation, short circuit, and overtemperature protection, as well as six-sided shielding. The IAD is available with optional enable and voltage trim pins. Please see the IAS series for single output applications. FEATURES • Industry Standard Package • Industry Standard Footprint • Fixed Frequency Design • 100°C Case Operation • Optional Trim and Enable • Wide Range Input • 1500V Isolation • Short Circuit Protection TECHNICAL SPECIFICATIONS Input Voltage Range 24 VDC Nominal 48 VDC Nominal Reflected Ripple Input Reverse Voltage Protection 18 - 36 VDC 34 - 75 VDC 25 mA Shunt Diode Output Setpoint Accuracy Auxillary Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit / Overcurrent Protection Power Limit Threshold Range ±1% 5% 0.5% V out 1.0% V out 10 % Iout Rated 25% Iout 4% Vout 500 µs ±10% Hiccup 110 - 150% 90 85 80 EFFICIENCY % Efficiency vs. Load (48V Input) 75 70 65 60 55 50 10 20 30 40 50 60 70 80 90 100 LOAD % EFF. IAD010ZGG EFF. IAD012ZHH EFF. IAD012ZJJ General Turn-On Time Remote Shutdown Switching Frequency Isolation Input - Output Output - Case (for 48 Vin) Input - Case (for 24 Vin) Temperature Coefficient Case Temperature Operating Range Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (Approx.) 300 ms Positive Logic 400 kHz 1500 VDC 500 VDC 1050 VDC ±0.03%/°C -40 To +85°C -40 To +110°C 95% 5 g, 10 - 55 Hz 1.8 X 106 hrs UL, CUL, VDE 1.2 oz † †† Notes MTBF predictions may vary slightly from model to model. Industrial temp range available Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. C-70 IAD SERIES - DUAL OUTPUT, 12 WATT MODELS - (See the last page of this file for options.) Vin (Volts) 24 24 24 48 48 48 Vin Range (Volts) 18 - 36 18 - 36 18 - 36 34 - 75 34 - 75 34 - 75 Iin Max.* (Amps) 0.80 0.85 0.85 0.40 0.43 0.42 Vout (Volts) ±5 ±12 ±15 ±5 ±12 ±15 Iout Rated (Amps) ±1.0 ±0.5 ±0.4 ±1.0 ±0.5 ±0.4 Ripple & Noise Pk-Pk (mV) 75 120 150 75 120 150 Efficiency Typ. ** 77% 82% 83% 78% 82% 83% Model IAD010YGG † IAD012YHH IAD012YJJ † IAD010ZGG IAD012ZHH IAD012ZJJ † Denotes advanced product release. Consult factory for product availability. * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 1.00" (25.4mm) 0.18" MIN. (4.6mm) BOTTOM VIEW 4 5 6 0 2.00" (50.8mm) 1 2 3 DIA 0.040" (1.0mm) 0.800"(20.3mm) 1.40"(35.6mm) 0.900" (22.9mm) 0.800" (20.3mm) 0.500" (12.7mm) 0.400" (10.2mm) 0.42" (10.7mm) 0 0.300" (7.6mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 15.4 12.2 9.3 7.4 6.4 °C/W °C/W °C/W °C/W °C/W P in 1 2 3 4 5 6 Function +Vin -Vin Optional Shutdown +V out Common -V out Tolerances Inches: .XX ± 0.020 .XXX ± 0.010 Pin: ± 0.002 Case: + 0.04, - 0.00 (Millimeters) .X ± 0.5 .XX ± 0.25 ± 0.05 + 1.0, - 0.0 Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. (Tolerances as listed unless otherwise specified.) C-71 OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION Negative Logic Lucent Compatible Trim Terminal Strip Trim Enable Trim and Enable Current Share Headerless SUFFIX N T TS 1 2 3 4 Y APPLICABLE SERIES HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD HAS, HBD, HBS, HES, QBS, QES XWS, XWD, XWT IAS, LES IAD, IAS, LES, SMS IAS, LES SMS Encapsulated EWS, IWS, OWS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF PIN LENGTH AND HEATSINK OPTIONS 0.110” (2.8mm) Pin Length 0.150” (3.8mm) Pin Length 0.24” (6.1mm) Horizontal Heatsink 0.24” (6.1mm) Vertical Heatsink 0.45” (11.4mm) Horizontal Heatsink 0.45” (11.4mm) Vertical Heatsink 0.95” (24.1mm) Horizontal Heatsink 0.95” (24.1mm) Vertical Heatsink 8 9 1H 1V 2H 2V 3H 3V All Units (Except SMS) All Units (Except SMS) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) All Units (Except DIP, SIP, and SM Packages) Standard Pin Length is 0.180” (4.6mm) Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. C105