LPC1902-7D

PC Series 190...230 Watt AC-DC Converters Converter with single stage AC to DC conversion and PFC No electrical isolation input to output Input voltage range 85(95)...255 V AC LGA • Extremely slim case (4TE), fully enclosed • Single outputs for 72 and 85 V DC loads • Ideal to supply isolated P series DC-DC converters • Operating ambient temperature range –40...71 °C with convection cooling Selection chart Output 1 Input voltage Rated power Uo nom [V DC] 72 85 Io nom [A] 2.7 2.7 Ui [V AC] 85...255 95...255 Po max [W] 190 230 Efficiency h [%] 94 94 Type Options LPC 1901-7D LPC 1902-7D -9 -9 Input Input voltage Input frequency Inrush current continuous range extremely low input capacitance of 1.25 µF 85(95)...255 V AC 47...63 Hz negligible Output Efficiency Ui nom, Io nom Output voltage setting accuracy Ui nom, Io nom Output voltage noise IEC/EN 61204, low frequency IEC/EN 61204, switching frequency Line regulation Ui min...Ui max, Io nom Load regulation Ui nom, 10...100% Io nom Ui nom, 0...10% Io nom Minimum output current not required Power limitation approx. 1 s, restart after 3 s Current limitation approx. 1 s, restart after 3 s Operation in parallel by load regulation Hold-up time Uo = 72...66 V DC, Po = 190 W Uo = 85...40 V DC, Po = 230 W 94% ±2 V Uo nom typ. 5 Vpp typ. 25 mVpp typ. ±1 V typ. 250 mV typ. 700 mV 0A typ. 240 W typ. 200% Io nom up to 5 units typ. 4.3 ms typ. 24 ms www.power-one.com Edition 4/04.2001 1 Cassette Style Protection Input undervoltage lockout Input overvoltage lockout Input transient protection Output Output overvoltage Overtemperature PC Series typ. 68 V AC typ. 306 V AC two varistors no-load, overload and short circuit proof suppressor diode in each output switch-off with auto restart typ. 150% Uo nom TC typ. 110 °C Control Status indication Isolated open collector signal LED: OK In OK/Out OK feature D Safety Approvals Class of equipment Protection degree Electric strength test voltage EN 60950, UL 1950, CSA C22.2 No. 950 class I IP 40 1.5 kV AC I/case and O/case EMC Electrostatic discharge Electromagnetic field Electr. fast transients/bursts Surge Conducted disturbances Electromagnetic emissions IEC/EN 61000-4-2, contact/air, level 2/3 (4/8 kV) IEC/EN 61000-4-3, level 2 (3 V/m) IEC/EN 61000-4-4, level 3 (2 kV) IEC/EN 61000-4-5, input, level 2/3 (1/2 kV) IEC/EN 61000-4-6, level 2 (3 V) CISPR 22/EN 55022, conducted CISPR 14/EN 55014, radiated criterion B criterion A criterion B criterion B criterion A class B below limit Environmental Operating ambient temperature Operating case temperature TC Storage temperature Damp heat Vibration, sinusoidal Shock Bump Random vibration MTBF Ui nom, Io nom, convection cooled Ui nom, Io nom non operational IEC/EN 60068-2-3, 93%, 40 °C IEC/EN 60068-2-6, 10...60/60...150 Hz IEC/EN 60068-2-27, 11 ms IEC/EN 60068-2-29, 11 ms IEC/EN 60068-2-64, 20...500 Hz MIL-HDBK-217E, GB, 40 °C, notice 2 –25...71 °C –25...95 °C –40...100 °C 56 days 0.35 mm/5 gn 50 gn 25 gn 4.9 gn rms 763'000 h Options Extended temperature range –40...71 °C, ambient, operating -9 www.power-one.com Edition 4/04.2001 2 PC Series Mechanical data 190...230 Watt AC-DC Converters European Projection Tolerances ±0.3 mm (0.012") unless otherwise indicated. 104 (4.09") 20 (0.79") 35 (1.38") M3, 4 deep Measuring point of case temperature TC 8 (0.31") 65 (2.56") 111 (4.37") Potentiometer (option P) LED "OUT OK" 19.8 (0.78") 171.93 (DIN 41494) (6.76") 164 (6.46") 127 (5.18") S09106 www.power-one.com Edition 4/04.2001 3 Cassette Style Pin allocation Pin no. 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Electrical determination Output voltage negative Output voltage positive Phase Neutral Protective earth Protective earth Output good Output good Output voltage positive Output voltage negative Output voltage positive Output voltage negative 30 26 22 18 14 PC Series 10 6 S10025 Vo– Vo+ P N 33 28 24 20 16 12 8 4 n.c. n.c. Out OK+ Out OK– n.c. Vo+ Vo– Vo+ Vo– Accessories Front panels 19” (Schroff/Intermas) Mating H11 connectors with screw, solder, fast-on or press-fit terminals Connector retention facilities and code key system for connector coding Flexible PCB for connecting the converter via an H11 connector, if mounted on a PCB Chassis or wall mounting plates for frontal access Universal mounting brackets for chassis or DIN-rail mounting www.power-one.com Edition 4/04.2001 4