SIE503.3LTR

SIP/SIE500 DC-DC Series Data Sheet Non-Isolated, 20 Watts Features • • • • • • • • Non-Isolated High Efficiency Topology Excellent Transient Response Sense and Power OK (SIE Model Only) Surface-Mount Construction Voltage Trim Vertical or Horizontal Mounting Water Washable Description SIP/SIE non-isolated step-down DC-DC converters deliver high efficiency and excellent transient response in an industry-standard SIP package. The SIP/SIE Series has output voltages ranging from 1.2 to 3.3V and up to 6 amps of output current. The SIE model has power OK and remote sense pins for added flexibility and improved point-of-load regulation. The SIP/SIE Series is available for vertical or horizontal mounting. The SIP/SIE Series uses 100% surfacemount construction for maximum reliability and features over seven million hours MTBF. Technical Specifications Input Voltage Range 5 VDC Nominal 4.5 - 5.5 VDC Efficiency vs. Load Output 90 ±1% 1% Vout Load Regulation Iout Min.- Iout Max., Vin Nom. 1% Vout Ripple and Noise, DC - 20 MHz Remote Sense Headroom Current Limit Protection Type Current Limit Threshold Range, % of Iout Rated 50 mV Pk-Pk 0.25 V Foldback 120% to 180% Short Circuit Protection Type 88 86 EFFICIENCY % Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated 84 82 SIP502.5 EFF. (4.5v) 80 Continuous EFF. (5v) 78 Power Good Signal (SIE model only); Asserts “High” When Vout is Between the Following Thresholds: Lower Sense Threshold, % Vsetpoint Upper Sense Threshold, % Vsetpoint Power Good Signal Reference Vout Ramp Up Rate, Minimum 76 10 -16% to -10% +10% to +16% Common Ground 0.5V/ms MTBF† (Bellcore TR-NWT-000332) Safety Weight (approx.) 20 30 40 50 60 70 80 90 100 LOAD % Notes General Remote Shutdown Switching Frequency Temperature Coefficient Ambient Operating Temperature Minimum Required Airflow Storage Range Humidity Max., Non-Condensing Vibration, 3 Axes, 5 Min Each EFF. (5.5v) Negative Logic 330 kHz 0.03%/°C 0 to +55°C 200 LFM -25 to +120°C 95% 5 g, 10 - 55 Hz 7.1 x 106 hrs UL, cUL, TUV 0.25 oz † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. REV. MAY 07, 2004 Page 1 of 2 SIP/SIE500 DC-DC Series Data Sheet Non-Isolated, 20 Watts Model Selection INPUT VOLTAGE (VOLTS) INPUT VOLTAGE RANGE (VOLTS) MAXIMUM INPUT CURRENT (AMPS)* OUTPUT VOLTAGE (VOLTS) RATED OUTPUT CURRENT (AMPS) TYPICAL EFFICIENCY** SIP501.2LT SIP501.5LT SIP501.8LT SIP502.1LT SIP502.5LT 5 5 5 5 5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 4.5 - 5.5 2.3 2.7 3.1 3.5 4.0 1.2 1.5 1.8 2.1 2.5 6 6 6 6 6 70% 75% 77% 81% 83% SIP503.3LT 5 4.5 - 5.5 5.1 3.3 6 87% SIE501.2LT 5 4.5 - 5.5 2.3 1.2 6 70% SIE501.5LT 5 4.5 - 5.5 2.7 1.5 6 75% SIE501.8LT 5 4.5 - 5.5 3.1 1.8 6 77% SIE502.1LT 5 4.5 - 5.5 3.5 2.1 6 84% SIE502.5LT 5 4.5 - 5.5 4.0 2.5 6 83% SIE503.3LT 5 4.5 - 5.5 5.1 3.3 6 87% MODEL NOTES: * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. Model numbers highlighted in yellow or shaded are not recommended for new designs. For right-angle pins, add suffix R to model number. Mechanical Drawing 0.55" (14.0mm) 0.55" (14.0mm) 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 6 7 8 9 10 11 0.13" (3.3mm) 0.13" (3.30mm) 0.28" (7.10mm) 0.100" TYP. 0.025" SQ. (0.64mm) (2.54mm) 1.90" (48.26mm) 2.50" (63.5mm) 0.025" SQ. (0.64mm) 1.90" (48.26mm) 2.50" (63.5mm) 0.10" TYP. (2.54mm) 0.11" (2.80mm) 0.28" (7.10mm) 0.25" (6.40mm) SIP MODEL 0.28" (7.10mm) SIE MODEL 0.100" TYP. (2.5mm) 1.90" (48.3mm) 2.50" (63.5mm) Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 24.4 °C/W 18.3 °C/W 15.0 °C/W 11.1 °C/W 7.9 °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. 1 2 3 4 5 0.13" (3.3mm) 0.27" (6.90mm) Pin 0.28" (7.10mm) 0.09" (2.30mm) 6 7 8 9 10 11 0.100" TYP. (2.5mm) 1.90" (48.3mm) 2.50" (63.5mm) 0.13" (3.3mm) 0.27" (6.90mm) Function 1 +Vout 2 +Vout 3 4 Sense (SIE) +Vout 5 6 7 Ground Ground +Vin 8 +Vin 9 10 11 0.025" SQ. (0.64mm) 0.55" (14.0mm) 0.09" (2.30mm) 6 7 8 9 10 11 Thermal Impedance 0.25" (6.40mm) 0.025" SQ. (0.64mm) 0.55" (14.0mm) 1 2 3 4 5 0.11" (2.80mm) PWR OK (SIE) Trim Enable REV. MAY 07, 2004 Page 2 of 2 Tolerances Inches: .XX ± 0.020 .XXX ± 0.010 (Millimeters) .X ± 0.5 .XX ± 0.25 Pin: ± 0.002 ± 0.05 (Dimensions as listed unless otherwise specified.)